Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The floorboard opening and the steering column seal bracket may not allow sufficient clearance for the shaft to turn freely in the center of the bracket/seal. The pinch bolt in the column yoke may bind or lock the column against the…
The right hand clearance lamp IS obscured, from certain angles of vision, by the in-line precleaner air cleaner cap. The involved vehicles fail to conform to federal motor vehicle safety standard no. 108, "lamps, reflective devices, and…
Incorrect information on tire placards constitutes a failure to comply with federal motor vehicle safety standard no. 110, "tire selection and rims". The information concerning tire sizes and inflation pressures IS applicable to both two…
There may be a missing duct collar between upper and lower air conditioner units. On units with optional heating capabilities, if the blower fails, the excess heat produced will not be contained in the area of the safety limit switch.
The area surrounding the gasoline filler pipe shroud may not be properly sealed. This may allow gas vapors to travel into the interior of the coach when refueling.
The hydraulic brake fluid used in certain vehicles may fail to comply with the brake fluid boiling point requirements of federal motor vehicle safety standard no. 116, "motor vehicle brake fluids". Braking efficiency may be reduced and…
There may be an insufficient permanent lubrication in the buckle/release mechanism of the type 2 seat belt assemblies. This may cause front seat occupants to have difficulty in fully fastening seat belts, although they may seem to be fully…
An insufficient weld may exist in the reinforcing gusset plate on front, right and/or left spring hanger, or the weld may be missing entirely. The spring-hangers are brackets located on either side of the axle. Defective or missing welds…
Incorrect bolts may have been used to secure the drive-line flanges to the front and rear pump flanges. Under high torque load, the drive line could separate.
Vehicles may have been assembled with a restricted fuel supply system that does not function properly. The engine may stop unexpectedly, even though the fuel gauge indicates fuel IS available.
The seven-blade engine cooling fan IS subject to fatigue cracking during normal operation. Portions of the blades may separate without prior warning.
Due to a manufacturing error, certain flexible-blade engine cooling fans may be subject to fatigue cracking and blade separation during vehicle operation.
An air brake hose fitting beneath the floor of the subject vehicles may rub against the rotating steering drive shaft, eventually causing the shaft to fracture. This condition could exist if a mechanic failed to orient the threaded 90…
The set-screw may not be positioned correctly, allowing the drive key to slide out of the hub and the hub and sprocket to disengage. This would cause the wheelchair platform to fall to the ground without prior warning.
Transmission may fail to perform properly due to insufficient lubrication. This could lead to transmission lock-up during operation without prior warning.
The spring-hangers, which are brackets located on each side of the axle, have a tendency to bend when subjected to repeated or severe jolts or stresses. Eventually they may break, causing the axle to become detached from the trailer and…
The mechanism which locks the wheelchair lift platform outer barrier in the "up" position during platform lift and lower modes may malfunction. This can result in the outer barrier collapsing.
"B" load range tires have been installed on vehicle, rather than "c" load range as indicated on federal sticker. Federal regulations require the use of a "c" load range tire on a trailer in this weight class. The lower "b" range tire may…
The balance weights which are attached to the front wheel of the motorcycle may cause the front tire to leak air slowly. If the air pressure gets low enough, the tire may shift on the rim and deflate rapidly.
Due to an interference problem with the front axle brake drum mounting bolts, the spare wheel may not seat securely against the hub when placed on the front axle.
The nuts fastening the stabilizer bar and the lower ball joints to the lower link may become loose, possibly resulting in detachment of the stabilizer bar or lower ball joints.
The parking brake linkage may not exert sufficient force to the parking brake system to hold the vehicle when parked on a slope.
Prolonged contact with road salt may, under certain conditions, cause serious rusting. This can weaken certain undercarriage components: lateral suspension arms, front crossbeam and strut coil spring lower supports.
The involved vehicles were modified by removing two rear seats and installing two full size seats in their place. This creates a conflict with federal motor vehicle safety standard no. 217, "school bus emergency exit extension". The…
The cotter pin, which IS used to secure the rear axle shaft lock nut, may have been inadvertently omitted during vehicle assembly. If the cotter pin IS missing, the lock nut could loosen during vehicle operation. This could lead to a…
Certain vehicles could be subject to a fuel leakage in the engine compartment due to the possibility of deterioration in the integrity of the high pressure fuel hose connections.
The involved pick-up trucks may exhibit vibration or shimmy in the front suspension and steering system under certain driving conditions.
Due to insufficient grounding of the internal ignition distributor parts, the ignition could misfire. This could adversely affect vehicle driveability and longevity of the distributor components.
The pushrod may have been incorrectly mounted to the lower of two holes in the brake pedal assembly. Incorrect mounting can cause sideload forces to be applied to the pushrod, causing the pushrod to fracture.
An extra adapter fitting used along with an incorrect through-frame fitting may have been installed in the fluid line. The additional length of the extra fitting could move the fluid line into a position of interference with the clutch…