Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
A ground fault may occur in the stoplight switch which IS located on the right handlebar in the throttle twist grip housing. consequences of…
The saginaw tilt steering column assembly has two pivot bushings and two mating retaining bolts. These retaining bolts can loosen, which could allow the pivot bushings to move into the turning arc of the column shaft universal…
The weld attachments of the front spring hanger, on both sides of the trailer, to the trailer frame may break if the running gear of the trailer catches on an obstruction and the operator pulls it free with the tow vehicle.…
The manual steering gear unit may lack integrity due to the heavy use of road salt in certain areas of heavy snow fall. consequence of…
U bolts used to secure the truck body to the chassis may fracture under normal stress. consequence of…
The lp gas distribution system where the lp line passes over the rear suspension leaf spring does not have enough clearance and could allow contact between the lp line and the leaf spring. This could lead to failure of the…
The wood anchor screws holding the inboard end of the furnace may not have been installed. Thus, the furnace may shift position or bounce while traveling.…
An engine compartment fuel hose routed to the fuel system pressure regulator may have an inadequately tightened hose clamp. consequence of…
Wire in battery charging circuit cannot tolerate the maximum current drawn by the alternator. Under repeated high electrical load, heat will build up at connector terminal area, melting the plastic wire harness, possibly discharging…
Metal burrs and sharp edges on fuel rails may have damaged adjacent o-ring seals during assembly. The defect could cause fuel leakage when engine IS operating.
Required front center seat belt assembly was omitted. Vehicles are not in compliance with the requirements of federal motor vehicle safety standard 209, seat belt assemblies.
The weld between the grabhandle and mounting plate may fail, causing grabhandle to come off unexpectedly.
A poorly designed bracket which mounts the service/parking brake unit to the rear drive axle may allow damage to brake chamber. Damage may cause the spring brake to be applied.
Under extreme conditions, one or both rear brake drums may unexpectedly crack, creating an unbalanced braking condition.
Some drag link parts can separate from the assembly which connects steering gear pitman arm to the front axle steering arm.
Failure to conform to federal motor vehicle safety standard 119, new pneumatic tires for vehicles other than passenger cars. Load range designation (a) IS missing from side wall. Consumer information concerning braking distance was not…
The engine oil pressure sending unit may develop an oil leak.
Some of the dual wheel assemblies were provided with ford wheel centers which do not seat properly on toyota brake drums. This IS due to a machine screw which protrudes from the drum. The mismating of wheels with brake drums can cause…
A defective toggle switch may have been installed in the sleeper of some trucks. The problem may cause an intermittent short circuit, resulting from constant vibration of the vehicle which may cause the switch terminal to wear through the…
Displacement of the fuel hose during assembly. At or near full throttle, a roller on the fast idle arm of the throttle linkage can catch behind one of the fuel lines, causing the throttle to stick wide open.
The rear axle control arm locates and helps control axle movement; it attaches to the frame with a bracket. The rear control arm bracket attaching bolts used on some of the involved vehicles may fracture. Fracture of all four bolts on one…
The vehicles were assembled with front seat belt retractors which may not perform adequately during a collision.
The hose connected to the pump located inside the fuel tank may become disconnected when the vehicle IS in use. If this happens, the fuel supply to the engine will be interrupted, causing the vehicle to stall.
The fuel caps on the involved vehicles do not seal properly and are not in compliance with federal motor vehicle safety standard no. 301, "fuel system integrity." contact with fuel causes the fuel cap gasket to swell, preventing adequate…
The metal fuel supply tube may crack at the fuel pump end due to vibration. The crack may result in fuel leakage. (The fuel supply tube connects the fuel pump to the fuel filter.)
Rear axle assembly may have axles that were improperly manufactured. This condition may result in separation of the axle shaft and wheel assembly from the vehicle.
The welding of the brake mounting flanges to the rear axle may be defective and may break. If this weld were to separate during vehicle operation, adjacent brake lines could be damaged.
The potential for fuel leakage exists in the engine compartment at the fuel reservoir seam and its hose connections. The fuel reservoir IS a silver colored can mounted to the air cleaner.
The switch used may not be compatible with the wiper motor. This system, although functional, IS not in compliance with federal motor vehicle safety standard no. 104, "windshield wiping and washing system". The windshield wiper speed may…
The front seat belt assembly may require more effort than usual to release and fails to meet the requirements of federal motor vehicle safety standard 209, "seat belt assemblies".