Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The parking brakes may have cracks in the brake actuating cam and lever of the brake assembly. Failure of the cracked part from repeated brake applications will cause the parking brakes to be inoperative.…
Excessive tolerance variation may have created a gap between the bumper bracket rail and the right front frame of the rear side member. This could result in insufficient spot welding adhesion at this location. Under…
Wiring of the battery charging system causes unequal charging which could overcharge the small generator battery. consequence of…
Nylon fuel lines on the fuel return side of the fuel pressure regulator assembly may crack. consequence of…
Dual rear wheels may fail due to a set screw in the toyota design rear wheel drum which causes the wheel to crack in and around the bolt pattern with center section.…
The fan blade, when subjected to high stress levels, can fatigue and break apart at the hub while the engine IS running. consequence of…
The polyethylene nuts which hold the fuel sender unit may fracture causing the unit to loosen and leak gasoline. consequence of…
Motorhomes exceed the load carrying capacity of the S10 chassis due to inadequate sized rear axles and axle bearings. consequence of…
The GR#5 cap nut may not be strong enough to support the weight applied to the outer wheels. consequence of…
The rear brake pedal may prevent the master cylinder piston from returning to its proper position causing rear brake drag. consequence of…
The rear brake release time may be greater than the time specified in fmvss 121, "air brake system". In addition, some tractors may have warped parking brake apply springs which also effect the rear brake release time.…
Incorrect bolts were used in the transmission linkage adjustment mechanism. consequence of…
The generator "bat" terminal located on the rectifier end frame may contact the carburetor fuel inlet pipe. consequence of…
The kickstand system may experience some engine kickback due to improper starting procedure. consequence of…
The LN-2 passenger seat may not comply with fmvss 207 requiring that the seatback remain in its set position when subjected to a 3300 inch pound rearward force.…
Cars may lose the wire snap rings that hold the differential cross shaft in position in the rear axle differential case assembly, allowing the shaft to move.…
Pinboxes welded to the hitch of the 5TH wheel unit may bend under certain conditions where maximum stress IS approached or exceeded, causing the kingpin to break.…
The electronic engine control wiring harness insulation may be damaged due to copper spikes produced during the welding of its wires. this creates a potential for a short circuit between the wires which energize the fuel pump…
An aluminum casting flash on the face of the throttle body may break off and become trapped between the throttle plate and the bore in the throttle body.…
The certification label located on the left front door did not include a required federal certification statement. consequence of…
The clearance between the brake line at the rear axle and fuel tank retaining band IS not wide enough and allows the line to contact the band during severe operating conditions. Continued contact may cause the damaged brake line…
The dual double check valve may not release the proper air volume to the brake system, causing a slight timing delay between the tractor and the trailer brake system.…
Certain front drive steering assemblies may contain a faulty weld at the axle ball flange and housing connection. consequence of…
Dual rear wheel assemblies may fail due to an inadequate adapter which may cause an axle to break, and improper maintenance of torque on the lug nuts which may cause the wheel studs to break.…
The fuel return hose between the switching valve and the fuel tank sending units may be incorrectly connected. consequence of…
In certain high salt areas, the idler arm IS exposed to road salt which causes the dust seal to deteriorate resulting in idler arm pin corrosion. This causes the pin to freeze and break.…
Lockwashers were not installed on the bolts that attach the seat sliding track assembly to the lower frame member. consequence of…
Main fuel tank filler cap may disengage suddenly when removing the cap for refueling. The sudden cap disengagement permits expulsion of vapor and under some circumstances, sprays gasoline around the surrounding area or persons.…
The lap belt may disengage from the retractor assembly when it IS subjected to severe loads, such as a frontal accident, due to interference by two seat frame bolts.…
Some wagons were assembled with a JA2 rear system instead of the JA3 brake system. These station wagons may exceed the maximum stopping distance required by fmvss 105.…