Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The center bracket, one of the three used to hold the grab handle in place, contains a rivet which may not be properly align. this allows a small gap to exist between the rivet head and the bracket.…
First rear seats were installed with an incorrect left side seat riser which causes failure to comply with the seat and seat belt loading requirements of fmvss 207, seating systems.…
The spring eye bolt was not torqued properly and could fail due to the loose fit within the spring eye bushing/hanger bracket. consequence of…
There may be inadequate welding in some underbody structural areas, including those at the rear suspension attachments, which may cause it to separate.…
Left or right cab step may crack in its welded area due to flexing of the step during entering and exiting. consequence of…
The accelerator rod hole clearance IS not adequate and can cause the accelerator linkage to bind. consequence of…
Steering arm may crack after repeated full lock turns due to the lack of end-of-travel relief features. consequence of…
Incorrect inner wheel bearings were installed in the rear axles which wears a groove in the spindle due to a poor fit. consequence of…
Tires and rims mounted were not the proper matched. consequence of defect: improperly matched tires and rims could result in tears or other wear…
Certain brake master cylinders may have been overstressed and cracked during manufacture. consequence of…
Retaining bolts used throughout the car which ground certain electrical systems and components were improperly heat treated, making the bolts brittle and subject to breakage.…
The central tube part of the drag link, which IS set in a rotational position, does not have enough clearance between the nut or bolt head and the axle beam.…
The rubber valve which fits into the air booster may crack when the pressure becomes too high, allowing the brake fluid to flow into air booster causing the rubber valve to be caught between the rubber stem and the piston.…
The parking brake actuating lever cam may contain a quench crack which can widen, reducing the holding capability of the parking brakes.…
A forging defect IS present in the dana semi trailer king pin which causes it to fail. consequence of…
Fmvss 121 requires that the air operated oil line to the wet air pressure tank contain an automatic high pressure valve to protect the brake air lines. this pressure valve was omitted.…
An error in the installation of the brake air line resulted in connecting the front and rear air brake supply tanks in series without a check valve between them. If an air leak develops in either the front or rear brake…
Dislocation of a spring cover will not allow the shoulder belt to retract after being extended. consequence of…
The hydraulic parking brake control valve may inadvertently activate due to momentary pressure disruptions within the system and cause the parking brake to be applied, stopping or slowing the truck unexpectedly.…
The reinforcing plates were omitted from the trailer pin box assembly, which IS used to hold the fifth wheel assembly to the trailer.…
Incorrect budd wheels of a lower than required load rating were installed on some trucks. the installation of these wheels causes the fire trucks to be in noncompliance with fmvss 120 and may fail during use.…
An inductive voltage spike may affect the rear door time delay relay in a manner which causes the magnetic brake valve to energize. when this valve IS energized the bus brakes are applied.…
Vans equipped with the optional sunscreen rear glass which has less than 70 percent luminous transmittance and does not have a passenger side outside rearview mirror are not in compliance with fmvss 111, rear view mirrors.…
Two welds connecting the pintle hook crossmember assembly to the trailers suspension subframe have been omitted. this causes cracks to form on crossmember when towing another trailer.…
The splined coupling between the steering column and steering box could develop internal corrosion due to its exposed position and characteristics.…
The front wheel bearing may deteriorate, causing vibration and noise from the front suspension assembly. consequence of…
There may be interference between the fuel tank and surrounding panels causing abrasion of the fuel tank surface. consequences of…
The certification label for the truck was omitted. consequence of defect: gross vehicle weight and tire capacity information IS missing.…