Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The throttle angle sensor on the carburetor may contain a nylon rotor which has not been heat treated. rotors that have not been heat treated contract in the presence of heat causing the throttle mechanism to stick.…
Transmission magnetic drain plugs may have been broken during assembly. consequence of…
Front steering knuckle thrust bearing may shatter into pieces due to improper heat treatment. consequence of…
The right quarter windows may contain glass which was improperly tempered. this glass may yield pieces larger than the maximum allowed by fmvss 205, glazing material.…
The lower control arms, which support the rear wheels, are subject to corrosion if operated in areas where a large amount of road salt IS used to aid in snow and ice removal.…
A brace between the seat mounting bolts and the chassis rail was omitted during assembly. this omission could cause severe distortion of the driver's floor area and seat would fail to meet requirements of fmvss 207-210.…
A wiring harness located under the instrument panel may not have been properly secured in its retainer and could interfere with the accelerator lever.…
Motor homes were built with clear plastic lenses and bulbs in the front turn signals instead of amber colored, which IS in noncompliance with fmvss 108-lamps, reflective devices and associated equipment.…
Fires from an undetermined cause have occurred in the air dryer compartment. the deicer system IS suspected and IS known to contribute to its intensity.…
Improper adjustment of entrance door causes latch to fail in the secondary latched position. such failure places the motorhome in noncompliance with fmvss 206, door locks and door retention.…
Gross weight ratings and tire pressures information on the certification label are incorrect, these do not comply to federal regulation part 567.…
The throttle return spring assembly may fail preventing the throttle from returning to the closed (idle) position when the accelerator pedal IS released.…
More fuel than permitted by fmvss 301 may escape from the fuel tank assembly under the test conditions described in the standard. consequence of…
A resistor in the electronic panel cluster may be subjected to an electrical current overload due to failure of a switching transistor.…
Bus seats may not meet the forward force/deflection performance test or the energy absorption requirements of fmvss 222, school bus passenger seating crash protection.…
The rubber valve of the brake air master (booster) may tear due to high fluid pressure developed during simultaneous application of both the service and rear wheel parking brake.…
Wiring connections in an electrical connector to the master cylinder reservoir fluid level sensors were reversed and fail to indicate low fluid levels as specified by fmvss 105, hydraulic brake systems.…
The front seat belt retractors, the center common seat belt mount and the rear inboard seat belt anchors were improperly installed. consequence of…
A battery cable routing change may cause the positive cable to rub against the right front spring rear hanger, possibly causing a short circuit in the cable at the point of chafing.…
The engine continues to run or can start up when the sentinel shutdown unit blocks the flow of fuel. this allows fuel pressure to build up in the fuel line which may cause the fuel line or filter to split open and leak or spray…
Cracks may develop in the welding of the structural support around the fifth wheel king pin. consequence of…
Large size particles in the steering hydraulic system fluid causes a solenoid valve orifice to plug and malfunction. consequence of…
The center bracket, one of the three used to hold the grab handle in place, contains a rivet which may not be properly align. this allows a small gap to exist between the rivet head and the bracket.…
Weldments on the wheel lift which attaches the hydraulic cylinder trunnion to the cylinder may fail. description of…
First rear seats were installed with an incorrect left side seat riser which causes failure to comply with the seat and seat belt loading requirements of fmvss 207, seating systems.…
The spring eye bolt was not torqued properly and could fail due to the loose fit within the spring eye bushing/hanger bracket. consequence of…
There may be inadequate welding in some underbody structural areas, including those at the rear suspension attachments, which may cause it to separate.…
Due to inadequate bonding, the crankshaft vibration damper assembly could separate. consequence of…
Accelerator control system failed to meet requirements of fmvss 124, which requires that when the throttle linkage fails, the engine speed returns to idle. the secondary throttle lever return spring and mounting bracket were…
Left or right cab step may crack in its welded area due to flexing of the step during entering and exiting. consequence of…