Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Solid material appearing to be epoxy/phenolic resin used to coat the inside of the drums in which the brake fluid IS packaged IS causing fluid contamination.…
The tailgate child lock can be opened from inside when the child lock IS engaged. the feature to prevent the tailgate from being operated from the inside of the station wagon may not function properly.…
The forward bolt that provides part of the attachment between the driver's seat back assembly and the seat cushion frame may be subject to fatigue fracture.…
Steering control arm can be overstressed with heavy steering input causing it to crack and it could eventually break completely. consequence of…
Possible damage in the lower inside sidewalls. This damage IS evident as tears in the rubber and fabric of the finished tire. consequence of…
Throttle cable may have been damaged during installation resulting in a bend or a kink or chafing and fraying of the braided wire cable. consequence of…
Possibility tires may develop separation in the shoulder area during the endurance test of fmvss 109, new pneumatic tires. consequence of…
Reflex reflectors fade over a period of time and therefore fail to conform to federal motor vehicle safety standard #108, color lighting for signal devices.…
Two throttle return spring defects are involved in this recall. (1) buses equipped with caterpillar engines may have a throttle return spring that breaks and prevents the throttle from returning to idle position when the driver's…
The brake wheel cylinder assembly experiences piston failure as a result of the composition of the material and causes the piston center link to be driven through the piston component.…
Failed to meet requirement of fmvss #109, "tire strength test." the test requires tire tread to be subjected to 3/4" diameter cylindrical steel plunger being forced into the tread at the rate of two inches per minute.…
Plastic shell of child restrain fractured during dynamic crash when tested in accordance with fmvss 213, child seating systems, when used in infant rear facing mode.…
Under certain specific load conditions, such as accidental high speed impacts on the rear suspension system, the rear wheel bearings and hub assemblies could deteriorate.…
The protective sleeve covering of the return fuel hose between the pressure regulator and fuel return pipe was shortened leaving part of the hose exposed. in some instances this part of the hose becomes kinked due to the engine…
A wire from the stop lamp switch to the speed control amplifier IS missing. This wire sends a signal to the cruise control to disengage when the brakes are applied.…
The lp gas regulator valve installed in recreational vehicle furnaces may leak through valve diaphragm. consequence of…
The brake mounting nuts which fasten the two brake assemblies to the axle knuckle on the front steering axle assemblies or the wheel end kits were not properly tightened.…
The detroit diesel allison engines 6V-92 and 8V-92 were equipped with fast idle air cylinders, which were improperly assembled. consequence of…
Limousines were built with a clear lens and clear bulb combination for the front park/turn signal lamp assemblies, instead of the amber color as required by fmvss 108, "lamps, reflective devices, and associated equipment."
An interference with the fit of the wheel to the front hub lugs could result in loosening of the lug nuts while driving. consequence of…
Turn signal and hazard warning switch fails to stay in locked "on" position when performing the hazard warning function. these units do not comply to fmvss #108.…
The engine air cleaner plastic trim cover could fall off the air cleaner assembly and land on the exhaust manifold creating a fire hazard.…
A resonant vibration can be initiated under certain operating conditions, causing a deterioration of the brake chamber which results in reverse brake cam rotation creating grabby brakes, brake chatter, or spring brake…
Screws holding support framing for liquid propane gas (lpg) tank and generator may not be properly installed and may cause the tank and/or generator to fall off the motorhome while on the highway.…
An incorrect steering shaft retaining nut IS installed on the shaft and can loosen causing steering play. consequence of…
The drag link to pitman arm toggle angle may be greater than design criteria, and may cause the steering to bind. consequence of…
Steering column boot attached to exterior of firewall could be deformed by the sound insulation placed on the firewall and causes interference with the steering shaft u-joint bolt.…
The sealant used on the injection pump could penetrate through the bushing and get between the throttle shaft and bushings causing the shaft to bind.…
The steering wheel to steering column securing nut may be upside down and/or improperly torqued and may loosen. this allows the steering wheel to become disengaged or detached from the steering column.…
Headlamp covers were installed on vehicles in error. causing the cars not to comply with fmvss 108, lamps, reflective devices and associated equipment.…