Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Under certain conditions, contacts in brake system relay could remain closed, causing the brake pump motor to run continuously, causing it to overheat and eventually fail.…
The ignition lock cylinder may hang up and not fully return to the "on" position from the "start" position after starting the engine. if this occurs, the engine will remain running, but the battery current to the…
Flexible brake hoses could separate from their end fittings due to silver brazing process used to join insert tube to the fitting. consequence of…
Cracks may develop in the main frame at the landing gear attachment due to defective welding. consequence of…
Steering column mounting bolts may be absent, leaving only the knee pad to hold the steering wheel and column in place. consequence of…
The sealant used on rough aluminum governor housing of certain fuel injection pumps could penetrate through the bushing when the engine temperature gets up to operating temperature and gets between the throttle shaft and…
Seat belt may loosen when extended completely from the non-locking retractor, even though it IS buckled and adjusted snugly. this allows the free end of the belt to creep back into the retractor without warning.…
Misadjustment of fuel distributor allows fuel to escape and be absorbed by the air filter. consequence of…
Longer brake lines required for these trailers affected brake release time which exceeded the maximum allowed by fmvss 121. consequence of…
If a certain type of rear end collision occurs, the edge of a welded bracket on the floor panel subframe may pierce the fuel filler pipe.…
The omission of two welds that connect the pintle hook crossmember assembly to the trailer suspension subframe causes fatique cracks to develop in the crossmember.…
Wheels may have been fitted to the truck hubs without the required adaptor plates causing the wheel to remain loose on the hub. consequence of…
Cracks have developed in some locking pin housings which locks the adjustable tandem trailer axle. consequence of…
The pinch bolt used to clamp the steering drive shaft yoke to the steering gear box shaft may have insufficient torque. consequence of…
There may be insufficient thickness of adhesive in the contact area between the bottom of the front windshield glass and the body. consequence of…
Valve stem may become unseated while burner control knob IS being turned allowing gas to escape. consequence of…
The rubber that encases ball stud and socket joint (connects steering drag link and pitman arm) may deteriorate, causing metal to metal contact, and may eventually result in complete separation.…
Left handed driver's side shoulder belt anchor plate may be upside down in lock pillar so that the unthreaded slot of the plate aligned with the hole in the lock pillar. this resulted in the anchor bolt being driven into the…
Composite graphite driveshafts are subject to overheating while idling, which may result in the driveshaft twisting and shortening causing the slip yoke to disconnect from the transmission.…
Heavy load and/or highly compressed rear suspension could cause the rear brake hose to contact the passenger's right footpeg securing stud, possibly fraying the hose.…
The distance between the fuel cock and carburetor may be insufficient to allow proper clearance for the outlet fuel line causing it to chafe.…
The bumper mounted cab entry step may fail due to improper welding or to nuts which attach the step pulling through the bumper lining.…
Buses may have been built with an incorrect type of steel tubing in the intermediate rear service brake lines which may leak or break during application of the brakes.…
Bolts in pivot shaft that attaches the swing arm to the frame may not be torqued to specifications. consequence of…
Severe brake chatter may cause the brake chamber mounting brackets on either side to develop cracks in the weld area where the s-cam shaft tube attaches to the chamber support section.…
Truck tractor to trailer hoses installed on these trucks may not meet adhesion requirements of fmvss 106, hydraulic brake hoses. the hose outer cover and braid did not with stand tensile force required by the standard.…
The aluminum wheel hubs develop cracks near the inner wheel bearing, allowing loss of bearing lubricant. consequence of…
The tailgate child lock can be opened from inside when the child lock IS engaged. the feature to prevent the tailgate from being operated from the inside of the station wagon may not function properly.…
The forward bolt that provides part of the attachment between the driver's seat back assembly and the seat cushion frame may be subject to fatigue fracture.…
Steering control arm can be overstressed with heavy steering input causing it to crack and it could eventually break completely. consequence of…