Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Due to a change in the original equipment manufacturers center section of the idler arm, the castellated nut which holds the idler arm could not be tightened enough to insert a cotter pin.…
Hose fails to meet requirements of fmvss 106, par. S7 3.7 adhesion between the outer corner and the braids. consequence of…
The vehicle frame may not withstand loading placed on it by the hitch. consequence of…
The area of hitch attachment may be of insufficient strength to support the hitch. consequence of…
Solid material appearing to be epoxy/phenolic resin used to coat the inside of the drums in which the brake fluid IS packaged IS causing fluid contamination.…
Reflex reflectors fade over a period of time and therefore fail to conform to federal motor vehicle safety standard #108, color lighting for signal devices.…
The brake wheel cylinder assembly experiences piston failure as a result of the composition of the material and causes the piston center link to be driven through the piston component.…
The lp gas regulator valve installed in recreational vehicle furnaces may leak through valve diaphragm. consequence of…
The brake mounting nuts which fasten the two brake assemblies to the axle knuckle on the front steering axle assemblies or the wheel end kits were not properly tightened.…
The detroit diesel allison engines 6V-92 and 8V-92 were equipped with fast idle air cylinders, which were improperly assembled. consequence of…
Turn signal and hazard warning switch fails to stay in locked "on" position when performing the hazard warning function. these units do not comply to fmvss #108.…
Information showing center of gravity measurements and proper truck camper match IS missing from owner's manual, failing to conform to the requirements of fmvss 126, truck/camper loading.…
The pressure relief device fails to vent the gas tank when the tank IS one fourth or less full and when a specified pressure IS reached.…
The quick release chin strap failed to meet the retention requirements of fmvss 218, motorcycle helmets. consequence of…
Wheels fail to comply with fmvss no. 120 due to incorrect size designation. the wheel IS marked 16 inch instead of 16 1/2 inch.…
Certification label fails to meet requirements of fmvss #126 "truck camper loading." also, required information IS missing from owner's manual.…
Weldments on the wheel lift which attaches the hydraulic cylinder trunnion to the cylinder may fail. description of…
Due to inadequate bonding, the crankshaft vibration damper assembly could separate. consequence of…
Accelerator control system failed to meet requirements of fmvss 124, which requires that when the throttle linkage fails, the engine speed returns to idle. the secondary throttle lever return spring and mounting bracket were…
Due to change in manufacturing process from a 15 inch drop center rim to a 14 inch drop center rim, the rim area was not reinforced properly.…
The light (photometric) output of the stop lamp, side marker lamp, side reflex and license plate lamps do not meet the requirements of fmvss 108. they are not as visible as lights which meet the fmvss requirements.…
Certain wind conditions can cause a down draft and create a slight positive pressure at the water heater flue gas outlet. This may cause a flame reversal to occur from the burner tube in the compartment between the water heater…
The cruise control causes the throttle actuator to stick preventing the disengagement of the throttle. consequence of…
A device to control the movement of the wheel chair lift IS needed to avoid sudden and unexpected movements of the lift. consequence of…
Diaphragm material which has rubber bonded to both sides of a nylon fabric reinforcement may have insufficient bond between the fabric and the rubber on one side of the diaphragm. If the diaphragm IS installed with the insufficient…
These wheels are made of two pieces, a disc and a rim, which are fillet welded together to form a finished assembly. The fillet weld was omitted in these wheels.…
Wire wheel package was assembled with incorrect wheel nuts that may not provide adequate retention. consequence of…
Wheels failed in dynamic radial fatigue tests conducted by nhtsa, therefore may crack or fail while in service. consequence of…
Power steering fluid packaged in containers and labeled as brake fluid. consequence of…