Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
A condition exists that allows oil to leak from the all wheel drive transfer case. Low oil levels in the transfer case can cause bearing damage and failure.
The gross axle weight rating certification plates are labeled incorrectly, stating the gawr as 20,000 lbs. The correct gawr IS 17,000 lbs.
The gross axle weight rating certification plates are labeled incorrectly, stating the gawr as 20,000 lbs. The correct gawr IS 17,000 lbs.
Improper installation of electrical wiring to the exterior lights (brake lights, running lights, and turn signals) of the trailer allows the steel lifting cables used to raise and lower the folding top to rub against the electrical wiring…
An incorrect tool was used to install pitman arm pinch bolts, resulting in inadequate torque on the pitman arm pinch bolts.
The passenger side air bag can experience an inflator ignition delay in the event of an accident. This does not comply with fmvss 208, "occupant crash protection."
The tie rod used on the dana FA-64 front drive axle has a threaded sleeve to permit toe-in adjustment without removing an end. The tie rod bar IS necked down to incorporate the sleeve. A stress riser IS created at the threaded portion of…
Defective battery operated smoke alarms, in which the horn may sound at a weak or low level or may not sound during operation, were installed in these vehicles.
The rear outboard lower safety belt attachment bolt was inadequately torqued on installation.
Nissan has made a preliminary determination that a defect exists in engine compartment component(s) that may fail due to the engine compartment heat.
The tire and wheel specification information on the certification label indicates a minimum tire size larger than the tire actually fitted to the vehicle. This does not comply with fmvss 120, "tire selection and rims."
The driver and passenger front seat manual reclining mechanisms do not comply with the requirements of fmvss 207, "seating systems." the seat back mechanisms will not latch under certain conditions.
The brake booster assemblies were improperly manufactured. This can cause the separation of the brake booster housing during a high effort braking maneuver.
The safety belt anchorage bolts do not comply with the requirements of fmvss 210, "seat belt assembly anchorages". The seat anchorages could not maintain load of 5,000 lbs for 10 seconds.
The safety belt retractor designed for the passenger side of the cabin was installed on the driver's side, and the driver's side retractor was installed on the passenger side.
The rear suspension, front spring hanger mounting assembly may fail under certain road conditions. A hard shock to the rear suspension may force the front spring hanger mounting bolts to shear.
Regular nuts, instead of locking nuts, were used to secure an extension arm from the forward side of the windshield wiper motor to the wiper arm. The non-locking nut can loosen and allow the extension arm to "slip" off the tapered shaft…
The generator exhaust pipe, located at the rear roadside of the vehicle, can emit hot exhaust gases from a damaged, worn, defective, or improperly installed exhaust pipe, melting the adjacent polyethylene storage trunk.
Passengers clothing can unknowingly become caught in the handrails at bus doors when exiting the bus.
The bracket that supports and positions the hand throttle cable at the accelerator rod can be bent or misaligned during body assembly to the chassis.
The carrier yoke bolts were manufactured with worn rolling thread dies, causing stress concentrations which caused cracks during the quenching process.
The rear axle can fracture because of metal fatigue.
The brake pedal linkage IS attached to the service brake valve pushrod with a clevis pin. The two cotter pins that retain the clevis pin may not have been installed during assembly.
The front wheel bearings were not adequately greased.
System: electrical.vehicle description: seq 9C1 police cars in corrosion areas of the us and canada only. note: vehicles originally sold or currently registered in the states of: connecticut, illinois, indiana, maine, massachusetts…
Separation of the transmission shift cable fitting end (vehicle interior) and the outer cable conduit.
Unanticipated heat in the transmission can force the transmission fluid out of the vent tube.
The malfunction or failure of a coolant system component results in significantly increased coolant temperature and a resulting increase in system pressure.
The brackets used to restrain the "reference-zero" arm of the drive axle slack adjusters may flex excessively, and prevent self adjustment of the slack adjusters. This could degrade brake efficiency as the brake shoes wear.