Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The outboard rear safety belt assembly will not release the webbing from the retracted position. This does not meet the requirements of fmvss 209, "seat belt assemblies."
As the brake pads wear, the brake caliper travel may be limited by interference with the main support member (z-bar spring) of the suspension.
Interference between the pitman arm and the steering gear housing due to insufficient clearance.
An engine compartment electrical wiring harness may have been routed too close to a sheet metal edge. The wiring can become damaged during normal vehicle operation due to chafing, resulting in an electrical short.
The attachment mechanism connecting the rear wheel assembly to the frame may fail.
The fuel filler hose or fuel filler vent hose was damaged by a drill bit used to install the dso package attaching hardware onto the floor pan.
The lower bracket of the rear suspension airbag may be mislocated, and may be rubbing against the brake line.
Proper operation of the throttle linkage can be restricted by interference with the air compressor breather tube.
The 15 inch wheels have malformed lug nut seat configuration which causes poor nut-to-wheel contact and centering of the wheel during installation.
Due to heat effects, the throttle bushing located on the accelerator control cable, can fatigue and break, causing the throttle linkage to separate.
The positive battery cable terminal at the starter solenoid may be formed incorrectly. Incorrectly formed terminals can contact the starter solenoid housing and cause an electric short circuit.
The car dolly wheels were installed with 90 degree cone lug nuts instead of 60 degree cone lug nuts. The lug nuts do not seat properly in the wheel holes and can become loose.
The pressure relief valve was omitted in the air tank. The air tank IS the reservoir for the air suspension and IS not brake related. Without the pressure relief valve, there IS no back-up system to limit air pressure in the air suspension…
The refrigerator installed in the trailer can overheat because the refrigerator baffle and flue vent are not properly aligned. Heat from the compressor will not vent properly.
The safety belt buckle assembly can get caught in the seat suspension mechanism. The movement of the air suspension seat could cause the safety belt buckle tether cable to fray .
The latching or locking pin on the mid-seating pedestal does not consistently meet the minimum load test, and does not comply with fmvss 207, "seating systems."
The windshield wiper motor may fail when left on during periods when the windshield has dried and friction on the wiper blades increases.
The transfer cases have been built with the wrong electric shift motor. The transfer cases can slip out of the 4 x 4 high gear position during coasting in forward gears or with power applied in reverse gear.
The fuel feed and return lines to the engine fuel injection system were not fully assembled and locked. The lines can work loose, causing a fuel leak in the engine compartment.
Vehicle description: diesel powered, rubber tire street cars, 24,ooo lbs. Gross vehicle weight equipped with a mobile-tech, model 3213, wheel chair step lift. the passive step lift's barrier which keeps a wheel chair and its occupant…
The front brake air lines are incorrectly routed through the pressure protection valve at the auxiliary wet tank. This results in lack of air pressure to the front brakes when the air pressure in the auxiliary wet tank drops below 65…
A weld in the door lock assembly used on rear and/or side emergency doors can be overstressed and break. When this occurs, a closed door cannot be opened, or if open it cannot be latched.
The power window and sunroof latch switches remain in an operational mode when the pressure IS removed, causing the window or sunroof to continue to close or open.
The mounting bracket for the rear trailer hitch may break because it does not have sufficient strength to withstand the loads of an attached trailer.
Salt corrosion products between the starter solenoid wire and the adjacent battery feed in the bulkhead connector may short these connections, causing the circuit to bypass the ignition key control of the starter motor solenoid. The car…
Some of the ABS equipped vehicles were built with an undersized brake return check valve. In incidents where hard brake pedal effort IS applied on low friction road surfaces, like rain covered streets, the valves may fail, causing the ABS…
The heat duct from the furnace to the fresh water tank compartment penetrates the generator compartment. This results in exhaust fumes entering the living area.
The lpg iron manifold system was not bonded to the chassis ground. This can create the potential for electrical arcing between the chassis frame and the lpg iron manifold system.
While operating the engine in reverse gear, engine torque causes the engine to roll, causing the throttle modulator cable assembly to contact the floor and bind the throttle cable holding the throttle in an open position.
Plastic hood insulation clip(s) was(were) inadvertently dropped into the hose between the charge air cooler and the throttle housing which can interfere with the throttle operation.