Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
These brake hose assemblies have inadequate crimps attaching the hose to the hose fittings and could cause the hose and fitting to separate.
The awning for the slide-out room of recreational vehicles can unfurl or unroll during transit causing the bracket to rip free of the sidewall of the vehicle.
These cruise control systems fail to hold the speed set by the driver and can accelerate above the intended set speed.
A 1/4" gas line coming out of the outlet side of the oven thermostat may have been improperly tightened.
When power IS applied intermittently to the receiver portion of the remote control, the receiver can lock up in an unknown state which may send a signal to the lift to deploy without a command from the driver.
Inside components of the valve fail to work properly due to insufficient clearance between the activation pin and bushing causing the valve to seize in the activated position.
An incompatibility can exist between the mineral oil and the hydraulic brake system of these vehicles.
These axles consist of a steel tubular center section and forged steel spindles that are welded to each end of the tube. Either spindle can contain a circumferential crack through a portion of its cross section.
The auto heater melts and can char carpeting.
A solder bridge on the printed circuit board within the fuse panel of the power converter passed undetected through a test fixture and bypasses the fuse protecting the circuit.
A solder bridge on the printed circuit board within the fuse panel of the power converter passed undetected through a test fixture and bypasses the fuse protecting the circuit.
Air blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer and…
The air cleaner baffle plate can detach and lodge in the throat of the carburetor.
These wheels are composed of 2 pieces - a disc and a rim which are normally welded together. These wheels lack the specified fillet welds.
Some temperature sensitive triggers were not x-rayed. These triggers could contain internal voids that would make the triggers susceptible to advanced creep causing false activation and venting of the CNG.
Some of these devices have experienced an electrical shorting within the module.
Some temperature sensitive triggers were not x-rayed. These triggers could contain internal voids that would make the triggers susceptible to advanced creep causing false activation and venting of the CNG.
Some temperature sensitive triggers were not x-rayed. These triggers could contain internal voids that would make the triggers susceptible to advanced creep causing false activation and venting of the CNG.
When installed in the vehicles, a tie wrap IS used to guide the cruise control cable in the engine compartment. some tie wraps have been installed with a large loop opening improperly guiding the cable which could prevent the throttle…
Upon exposure to impurities in the natural gas fuel in cold weather, an internal o-ring on these devices can blister during decompression after "fast-fill" refueling resulting in seal leakage.
As part of an ongoing recall campaign (93e-040), sofa safety belt buckle assemblies were being replaced. some of the corrective safety belt assemblies were sent out to dealers which were of the wrong design.
The water seal o-ring used in the valve end boss assembly of the "literider" cylinder could be improperly installed causing an interference condition.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
The transmission reverse switches can cause the backup lights to be inoperative. This does not conform to the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment."
Approximately 10" to 11" of excess webbing can cause the first point of lock-up to be delayed. This does not conform to the requirements of fmvss no.209, "seat belt assemblies."
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
A solder bridge on the printed circuit board within the fuse panel of the power converter passed undetected through a test fixture and bypasses the fuse protecting the circuit.
A wire from the low voltage output of the transformer can contact the chassis of the power converter. This condition can send large amounts of current (amperage) through the wiring of the vehicle for extended periods.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…