Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Water intrusion into the kick panel areas in front of both the driver and passenger doors can cause a corrosion path between the battery feed and the electrical ground.
The alignment bolt was not torqued to specification.
The retainer clip that holds the master cylinder push rod to the brake pedal arm IS missing.
These vehicles are equipped with a detroit diesel optimized idle system. if the ignition IS turned on and the fuse for the electronic control module (ecm) power feed line IS removed or burned out, the safety features designed to prevent…
A loss of power steering assist can occur due to the separation of the pulley from the power steering pump shaft.
The type 4 compressed natural gas (CNG) fuel tank supplied by edo canada can rupture during fueling.
These buses are equipped with compressed natural gas fuel tanks supplied by edo canada. the fuel cylinder straps expand when tanks are pressurized causing brackets to break the mounting hardware.
The power steering hose with a crimped end fitting was improperly manufactured.
The brake wire inside the trailer brake wiring plug was connected to the wrong terminal and, therefore, not properly connected to the switch in the truck cab which controls the trailer brakes.
Vehicle description: vehicles equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
If one of the headlamp wiper arms becomes misaligned, the wiper balde can lodge in the groove under the headlamp. if the washers are activated with the wiper blade in the misaligned and lodged position, the washer pump will run…
The four fasteners that retain the output shaft bearing to the steering column tilt/telescoping mechanism was not torqued properly.
A plastic coated steel support strap for the battery cable was damaged when it was crimped onto the cable.
The automatic transmission park pawl shaft may not be free to rotate as intended. if the park pawl shaft does not rotate, it would prevent the park pawl from engaging the park gear when the shift lever IS in the park position.
The latch plate used in the seat belt buckle was not manufactured according to design dimensions. if the seat belt tongue IS inserted slowly at an angle into the buckle, there IS a possibility of partial engagement.
The latch plate used in the seat belt buckle was not manufactured according to design dimensions. if the seat belt tongue IS inserted slowly at an angle into the buckle, there IS a possibility of partial engagement.
The rail of the automatic shoulder belt can wear sufficiently such that the cable which retracts the buckle assembly will become jammed in the rail rendering the shoulder belt inoperative.
The wiring from the electronic control unit was connected to the wrong wheel sensor or to the wrong brake modulator valve. it IS possible that either or both wiring may have occurred at either the front or rear axle or both axles.
The incorrect electricalmotor was installed on the fuel pump that supplies fuel to the engine. the motor was specified to be a continuous duty motor and the motors installed were intermittent duty motors. the intermittent duty motors…
Vehicle description: school buses built on gm P3 cutaway chassis. the school bus, when tested in accordance with fmvss no. 301, exceeded the allowable fuel spillage as specified by the standard. the fuel tank was punctured as a result…
The latch plate used in the seat belt buckle was not manufactured according to design dimensions. if the seat belt tongue IS inserted slowly at an angle into the buckle, there IS a possibility of partial engagement.
An item worn by a child, such as a long drawstring, sash, or backpack/bookbag accessory, can become caught in the area between the handrail and the floor.
The equalizing beam shaft of the tandem axle suspension were manufactured from as-rolled sae4140 steel rather than the specified annealed sae4140. these shafts can fracture inside the beam at the toe of the weld.
The bed assembly can bypass the stop mechanism allowing it to separate itself from the bed track.
Vehicle description: school buses built on gm P3 cutaway chassis. the school bus, when tested in accordance with fmvss no. 301, exceeded the allowable fuel spillage as specified by the standard. the fuel tank was punctured as a result…
Note: passenger side (right) seat belt assembly. the rail of the automatic shoulder belt can wear sufficiently such that the cable which retracts the buckle assembly will become jammed in the rail rendering the shoulder belt inoperative.
Note: driver's side (left) passive seat belt assembly. the rail of the automatic shoulder belt can wear sufficiently such that the cable which retracts the buckle assembly will become jammed in the rail rendering the shoulder belt…
The park pawl abutment bracket has a sharp edge which can cause the parking pawl to hang up and not engage the park gear. this would allow the vehicle to move even though the gear shift indicator shows that the vehicle IS in park.
An item worn by a child, such as a long drawstring, sash, or backpack/bookbag accessory, can become caught on the fateners that secure the handrail support to the handrail.
Air brake fittings and air brake hoses on the brake actuators can break because of insufficient vertical clearance under the air reservoir.