Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The awnings for the slide-out room can unfurl or unroll during transit causing the bracket to rip free of the sidewall of the vehicle.
The front seat belt warning chime does not sound with the seat belt unbuckled.
The low brake fluid level warning lamp does not illuminate during the ignition on, bulb test period.
Vehicle description: school buses and heavy duty trucks equipped with rear axle assemblies produced by dana spicer. certain rear axle assemblies were improperly heat treated which could allow pinion breakage at the pinion threads.
Vehicle description: school buses equipped with the international I6 electronic engine and an extra thick bus body floor. the accelerator pedal to floor clearance IS approximately 1.2 inches with a standard bus body floor. however, some…
The front impact beam installed on these motor homes can fall to the ground forward of the front axle.
The eco-cruise actuator can bind the throttle.
The e-z slide-out room can operate unexpectedly. water can cause an electrical short in the slide-out room control relay.
The drive axle housings consist of a plate steel center section and two forged spindles, one of which IS welded to each end of the center section. each spindle contains a keyway slot in which the locking tab for the wheel bearing nut…
Vehicle description: 3-wheel on-road vehicles, models 898464b, 898465a, 898474b, 898474c, 898475a and 898484. the door latch can release unexpectedly.
Vehicle description: all vehicles equipped with eaton drive axles and axilok spindle nuts. the drive axle housings consist of a plate steel center section and two forged spindles, one of which IS welded to each end of the center section.…
If the plastic pins and metal clip that retain the lower steering shaft in the upper shaft break, the lower steering shaft can separate from the upper shaft.
The steering wheel armature stamping can crack and separate from the center hub attachment to the steering column.
The fuel and rear brake tubes can experience accelerated corrosion between the tubes and a rubber isolator.
Vehicle description: transit buses equipped with marmon-herrington mc80b front steering axles. the left and right hand steering arms can crack and/or broken due to the manufacturing process.
Vehicle description: 1994 models are only in the state of california. the material hardness of the parking brake ratchet bar was greater than that of its mating part, the parking pawl.
Vehicle description: 4-door, 4-wheel drive and all-wheel drive multi-purpose passenger vehicles. during development testing, the prop shaft contacted the inboard side of the fuel tank allowing fuel leakage. this leakage was in excess of…
Vehicle description: heavy duty trucks equipped with horton fan drives. the fan drive control system was reconfigured which resulted in a significant increase in the demand for fan activation and associated stress to electrical and…
Two bolts that attach the driver air bag to the steering wheel were not installed during vehicle assembly.
These buses have a turn signal lever that will not operate consistently in the lane change mode if the lever IS not moved to the position where resistance to movement IS felt.
The seat belt retractor located next to the driver and passenger seats will not allow the belt to be extended so that it can be used.
A mounting bracket for the optional hwh jack can rub against the fuel tank when the vehicle IS in motion.
The recliner mechanism and the seat frame may have foam and/or vinyl vetween them, creating a "soft" joint. this "soft" joint results in lower than specified bolt torque which leads to joint looseness, causing bolt fatigue and eventual…
The main power cable can wear due to friction.
The ground studs in the engine and battery compartments do not offer adequate electrical conductivity.
The air/spring actuated parking brake chambers manufactured by midland (date code 145b6k) were filled with the wrong lubrication. the improper lubricant causes the seals within the chamber to fail and results in loss of air. if air…
These vehicles were manufactured with seat belt retractors out of design position which can cause the retractor to lock-up on slopes less severe than the fmvss requirement. this does not comply with fmvss no. 209, "seat belt assemblies."
The electrical wiring harness located to the right of the accelerator pedal and routed along the engine tunnel to the driver's seat base can chafe or rub by contact from the driver's foot.
Miswiring of the low beam headlamp receptacle for the replaceable halogen lamp causes a noncompliance to fmvss no. 108, "lamps, reflective devices, and associated equipment."
During assembly of the left rear quarter panel, some welds were missed. this does not comply with the requirements of fmvss no. 301, "fuel system integrity."