Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
A spacer was omitted at the lower seat belt anchor point of the driver and front passenger seat.
The protective cover for the underhood fuse center was omitted. without this cover, the positive terminal bolt on the fuse block IS exposed and can contact the insulated negative battery cable. if the insulation on the negative cable…
Vehicle description: passenger vehicles and MINI vans originally sold or currently registered in the following states: connecticut, illinois, indiana, maine, massachusetts, michigan, new hampshire, new jersey, new york, ohio…
The outboard safety belt webbing on the right-hand rear bucket seat can separate during a vehicle crash.
It IS possible to remove the ignition key while the cylinder IS in the run position. this does not comply with the requirements of federal motor vehicle safety standard no. 114, "theft protection."
Vehicle description: g vans equipped with 6.5L turbo-charged diesel engines. the front left-hand brake pipe can be contacted by the lower engine oil cooler hose causing a hole to be worn in the brake pipe.
Vehicle description: vans and trucks equipped with an optional automatic transmission shift lever that includes a park brake position. the transmission shifter/park brake lever can bind before fully engaging in the park brake position…
Due to a clearance between the oil separator plate and the differential housing of the front differential unit, oil leakage at the air breather plug can occur, when the vehicle IS operated continuously above 75 miles per hour.
Vehicle description: buses equipped with 4-stroke cycle engines. engine compartment fires have occurred at or near the webasto diesel fueled auxiliary heater.
Vehicle description: minivan equipped with second row bench seats with optional integrated child seat (ics). the headrest lockout mechanism on the seats may not engage and lock the headrests in the "down" position, as intended, when the…
Two hydraulic system pipes connecting the hydraulic brake pumps to the accumulators can contact each other, resulting in a hydraulic fluid leak.
The aluminum facia trim panel on the passenger supplemental restraint system (srs) air bag door can detach during air bag deployment.
The low pressure power steering return hose can either burst or become disconnected due to increased fluid viscosity in frigid temperatures.
An adhesive used in the seat belt retractor can cause the mounting to weaken.
Corrosion around the zinc-coated throttle control lever bushing can cause the throttle lever to bind.
The differential output shaft retaining rings on the rear suspension can become displaced allowing the output shaft to become detached from the differential unit.
The rear suspension tie rod assembly can fracture.
If the air bag computer in a subject vehicle experiences a mechanical shock (i.e., rapidly moving the front seat back against the stops or a sudden release of the parking brake) within a very short time after the engine IS started, the…
If the air bag computer in a subject vehicle experiences a mechanical shock (i.e., rapidly moving the front seat back against the stops or a sudden release of the parking brake) within a very short time after the engine IS started, the…
Vehicle description: electric vehicles. these vehicles were built with a drive motor charger receptacle assembly that was incompletely sealed. incomplete sealing can allow water to intrude into the circuit board.
Vehicle description: heavy duty trucks equipped with fd1060 and fd1460 diesel engines and optional manual fuel shutoff systems. the hand control of the manual fuel shutoff system, mounted on the vehicle's instrument panel, IS labeled…
The web mounted rear seat belt inboard anchor positions may not achieve the required load of fmvss no. 210, "seat belt assembly anchorages."
Vehicle description: vehicles equipped with memory seat option. the memory seat module wiring harness can come in contact with the seat spring, a low resistance short circuit can develop resulting in localized heating.
A gradual deterioration of the headlight plastic lens occurs.
These vehicles were assembled with center rear seat belt anchor bolts not properly installed. this does not meet the requirements of fmvss no. 210, "seat belt assembly anchorages."
These vehicles were manufactured without a lock washer and/or screws in the front hub.
These vehicles were manufactured without a lock washer and/or screws in the front hub.
Vehicle description: extended cab and 2-door utility vehicles equipped with reclining seats and the easy-entry feature. these vehicles exhibit a condition in which a pinch point exists in the recliner mechanism that can trap and pinch a…
An integrated circuit within the voltage regulator can contain manufacturing errors.
The vehicle identification number (vin) IS not in compliance with part 565, "vehicle identification number - content requirements."