Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Vehicle description: medium and heavy duty trucks, school and transit buses built with a bendix 9X3 power apply park brake system. the cam lever of the powered apply brake can move forward, because a hole in the transmission mounting…
Vehicle description: class-c MINI motor homes. the propane water heater IS located less than 3 feet from the gasoline filler spout.
The front axle brake hoses were damaged during transportation of the front axle assembly with the brake hoses attached.
The front axle brake hoses were damaged during transportation of the front axle assembly with the brake hoses attached.
A secondary bend operation was not performed during assembly of the door latch which could cause the door latch to jam when locked.
The electrical circuit design allows the potential for an inadvertent air bag deployment upon vehicle ignition shut down.
The bolts used to attach the strut to the body and the rear liftgate can accumulate fatigue damage if three factors combine. if the bolt IS loose, the gas strut IS over-pressurized, and the frequency of opening and closing cycles IS…
The headrest guide bracket was improperly welded to the seat back frame on the passenger side seat back assemblies only.
The guide rail on the driver's side contains a covered cable and also an angled belt guide at the top end of the webbing. the combination of these factors can lead, over time, to the cable's movement exerting abrading force to the lower…
Excess lubrication can cause the rubber door latch switch cover to deform, and the door latch switch to malfunction, so that the shoulder belt anchorage would remain at the a-pillar when the door was closed.
The lower seat back attaching bolt on the driver's seat can fail and separate.
Vehicle description: school buses. side emergency push-out windows may not open properly due to interference with exterior bow cap. emergency door(s) may not have required operating instructions located adjacent to interior door…
Vehicle description: trailers. incorrect seals were installed in the wheel assemblies.
Under certain high load operating conditions, the transmission fluid temperature can exceed the melting point of the material used in the connector to retain the fluid line to the transmission.
A short circuit condition can occur in the remote power mirror control switch circuit board as a result of a separated part of the contact assembly bridging the switch positive battery pad and adjacent chassis ground pad.
Vehicle description: multi-purpose passenger vehicles equipped with 5.0L engines originally sold or currently registered in the states of alaska, idaho, iowa, maine, michigan (upper peninsula only), minnesota, montana, nebraska, new…
The steel road wheels were damaged by the equipment used to match mount the wheel to the tire.
During assembly of the frame, a fillet weld that joins the inner steering gear attachment reinforcement to the frame rail, was omitted.
Vehicle description: pickup trucks equipped with diesel engines. the engine driven vacuum pump can allow engine oil into the vacuum hoses due to the absence of an internal check valve. the oil can cause the hose to deteriorate and…
The electronic brake control module or the electronic brake and traction control module can cause the antilock brake system (ABS) to cycle during a non-abs brake application.
The fuel pump mounting plate does not fully seal the fuel tank allowing fuel leakage onto the engine.
Vehicle description: conventional trucks and truck/tractors equipped with a firewall adapter plate for the steering shaft boot. Insufficient clearance between the top of the steering shaft and the top of the opening in the adapter plate…
Vehicle description: passenger vehicles originally sold or currently registered in the following states: connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, new hampshire, new jersey, new…
The release button used in the rear seat belt buckles were not made according to specifications. in hot weather, the plastic welds securing the release button to the spring can fail resulting in partial engagement of the seat belt tongue…
Vehicle description: glaval conversion vans and pickup trucks. the retainer clips were not removed from the rear brake drum wheel stud bolts prior to the installation of a custom wheel.
The guide rail on the driver's side contains a covered cable and also an angled belt guide at the top end of the webbing. the combination of these factors can lead, over time, to the cable's movement exerting abrading force to the lower…
The center rear seat belt anchor plate exhibits stress cracks.
Excess lubrication can cause the rubber door latch switch cover to deform, and the door latch switch to malfunction, so that the shoulder belt anchorage would remain at the a-pillar when the door was closed.
An in-line fuse to the auxiliary battery was omitted.
The "o" rings of the regulator assembly in the onan emerald and marquis brand generator sets can weaken and break when exposed to high ambient temperatures.