Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Vehicle description: motorcycles. these motorcycles were built with a fuel hose that could come off the carburetor.
Vehicle description: motorcycles. a section of the wiring harness located above the headlight IS routed incorrectly.
Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. the tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
Vehicle description: motor homes (models 222fd, 222qd, and 222hd). the wheel cover can rotate while mounted on the wheel.
Vehicle description: motor homes built on roadmaster chassis. as the result of the close proximity of the engine system in respect to the routing of the 12-volt dc battery cables, it IS possible for the insulation on the battery cable…
Vehicle description: heavy duty trucks. The steering shafts may have a defective or mis-located weld that could fail.
Vehicle description: passenger vehicles. The left front upper control arm may not meet the specified strength requirements.
Vehicle description: certain 2500 wagons were equipped with incorrect load range tires.
Vehicle description: certain sport utility vehicles are being recalled for a software error in the instrument cluster microprocessor. under certain conditions, the cluster, with the majority of its gauges, illumination, and warning…
Certain motor homes fail to comply with requirements of fmvss no. 120, "tire selection and rims for motor vehicles other than passenger cars." these motor homes were erroneously assigned inadequate tire inflation pressures and inadequate…
Vehicle description: certain school buses fail to comply with requirements of federal motor vehicle safety standard no. 221, "school bus body joint strength." these buses have insufficient metal hemming in the panel joints.
Vehicle description: fifth wheel trailers. the trailer pin box steel structure could fail at the welds or tubular steel structure due to fatigue.
Vehicle description: sport utility vehicles (4 wheel-drive). some of these vehicles were built with a range shift collar in the transmission transfer case that contains cracks.
Vehicle description: motor home chassis. the welds where the liquid propane (lp) gas tank bracketing joins the floor trusses may not be adequate.
Vehicle description: trailers equipped with american racing equipment aluminum wheels (part AR-62) combined with dexter axle six bolt hubs (part 008-201). certain aluminum wheels with a smaller diameter mounting surface are not…
Vehicle description: sport utility vehicles. The accumulator that IS installed on the hydraulic brake booster may have been improperly manufactured which, over a period of time, could result in leakage of the pressurized nitrogen gas from…
Vehicle description: sport utility vehicles. some of the brackets used to attach the two gas struts to the rear door (hatch) may have been improperly made. at high ambient temperatures, the increase in gas pressure in the strut(s)…
Vehicle description: passenger vehicles. the cooling holes in the steel wheel may have burrs on their edges as a result of improper manufacturing. these burrs can cause cracks as the vehicle IS being driven. cracks can propagate…
Vehicle description: transit cutaway buses equipped with telma brake retarder driveshaft system option on vehicles built on a ford E-450 chassis with 186" wheelbases. these vehicles can experience driveshaft failure.
Vehicle description: heavy duty trucks equipped with trw tie rod ends on certain meritor axles. the tie rod and drag link ball stud ends contain bearings that are below the specified case depth and/or hardness.
Vehicle description: fire trucks equipped with a drive axle suspension containing a spring beam with a thickness of 1.75". the spring beam in the suspension can fail causing the collapse of the drive axle suspension and allowing abrupt…
Vehicle description: on certain school buses equipped with I-6 engines, plywood floors, and a driver insulation package, the accelerator pedal can stick in either a partial or full throttle position.
Vehicle description: school and transit buses equipped with 39-inch flip seats. the flip seats could bind in the occupied position and not return to the stored position when not occupied. the cushion frame support bar slides off the…
Vehicle description: motorcycles. the flexible fuel hose leading from the fuel distributor can chafe against the rigid lines of the fuel feed and the return lines. continued chafing of the flexible fuel hose can lead to fuel leakage.
Vehicle description: heavy duty trucks equipped with 10,000 or 12,000 pound dana front axles. a condition called brake "sprag", which IS characterized by a noise at the end of an applied stop, can develop in the brake system. this…
Vehicle description: chassis built with a jacobs vehicle systems electronic controller for the electric driveline brake system. a failure mode within the solid state controller can cause a short from the positive terminal to the negative…
Vehicle description: l school buses equipped with a floor-mounted track used to accommodate and secure wheelchairs. the floor-mounted track bolts, used to secure this track to the floor, are too long and protrude through the wheel well.…
Vehicle description: transit buses. the clamp nuts for the center link tie rods may have been inadequately tightened.
Vehicle description: 1997-2001 chevrolet venture, pontiac montana/transport, and oldsmobile silhouette MINI vans equipped with passenger side power sliding doors that were serviced in campaign 01013 (01v-067) from april to august 2001.…
Vehicle description: heavy duty trucks built with a steerable auxiliary axle and equipped with certain meritor-wabco brake system two and four port relay valves. the valve may stick open when a high-pressure application IS released.