Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
On passenger vehicles with vehicle identification numbers (vin) starting with 1NX only and built from january 8 through february 13, 2002, it IS possible for the bolts that join the rear brake and hub assembly to the rear axle carrier to…
On certain electric vehicles, the brake master cylinder pushrod, which connects the brake pedal to the master cylinder, could fracture.
In some minivans, water and other contaminants (dirt, salt, etc.) can enter into the right rear passenger compartment due to a missing body sealer.
On certain pickup trucks equipped with manual transmissions, failure of the front parking brake cable input button could result in failure of the parking brake system to hold the vehicle stationary.
On certain minivans, some trim material can loosen and drop into the rear outboard seat belt assembly, causing the seat belt to become inoperative.
On certain sport utility vehicles, water and impurities can enter into the ignition switch, causing a short circuit.
On certain passenger vehicles. If the engine fails to start and the driver holds the key in the "start" position for an extended period, high current flows through the ignition switch, and sometimes produces enough heat to melt internal…
These motor homes are wired in such a manner that the vehicle operator must ensure that the battery disconnect switch IS in the "use" position to activate rear cap tail lamps, stop lamps, backup lamps, turn signal lamps, and clearance…
Certain passenger vehicles were built with missing or under-torqued steering gear attachment bolts. if a bolt IS missing, the driver may notice uneven steering response or unusual noises during turns.
On certain passenger vehicles with bumper numbers between 00-760 to 00-982 and with bumper numbers 01-228 to 01-269, improper heat-treatment of the wheels has occurred. one or more of the spokes on the wheels could crack.
On certain bus conversion motor homes, the support plate mounting holes were improperly drilled allowing contact between the front shock absorber dust covers and the air spring piston. the repeated motion of the shock absorber dust cover…
On certain walk-in vans equipped with seat belt buckles manufactured by indiana mills & manufacturing inc., after repeated flexing, the cable can fatigue and fray at the point where it IS crimped to the buckle.
On certain transit buses equipped with adhesively bonded aluminum bus door panels, due to an imperfect bonding of the door panel skin to the panel frame, environmental moisture may infiltrate regions of imperfect bonding and cause…
On certain heavy duty trucks equipped with replacement dana spicer tandem drive axle models ds463 and ds521, installed on vehicles from may 1, 2001 through february 1, 2002, an undersized attachment weld may fracture without warning.
On certain transit buses equipped with vanner 60 series battery equalizers, the equalizer could fail to operate properly and cause malfunction of the battery charging system.
Certain buses fail to conform to the requirements of federal motor vehicle safety standard no. 121, "air brake systems." these buses do not have a check valve between the wet tank and the secondary tank.
Certain passenger vehicles equipped with automatic transaxles were assembled with an inadequate weld at the brake pedal pad to brake pedal actuator arm assembly. during braking, the brake pedal pad could separate from the brake pedal…
On certain passenger vehicles, during the strut mount manufacturing process, the thrust bearing was not properly positions and secured. if the suspension IS fully unloaded, the front strut could separate from the upper mount.
On some passenger vehicles equipped with a nissan-approved accessory floor mat that was installed either at the assembly plant or by the dealer, due to the length of the driver side floor mat, a small amount of mat movement could cause the…
On certain school buses, galvanic corrosion on the die cast adapter plate causes distortion of the wagon wheel seals that are mounted on the adapter plate. if the seals become distorted, the tipper valves cannot properly seat against the…
On certain heavy duty trucks equipped with iros rear air suspensions, during assembly, four bolts and nuts holding the main support member bushing bar pins to the main support member hangers were incorrectly tightened.
On certain sport utility vehicles, if a driver has not placed the shifter lever fully into the "park" position and leaves the vehicle running, the vehicle may unexpectedly move rearward after seeming to be stable.
On certain low floor transit buses equipped with adhesively bonded aluminum bus door panels, due to an imperfect bonding of the door panel skin to the panel frame, environmental moisture may infiltrate regions of imperfect bonding and…
Certain passenger vehicles equipped with dunlop sp5000 tires. some of these tires have a separation around the entire circumference in the area of the side wall and tread.
Certain medium duty tilt cab trucks equipped with manual transmissions have a condition in which the clutch master-cylinder pushrod end that attaches to the clutch pedal pin can wear prematurely. the first noticeable effect of this wear…
Certain medium duty tilt cab trucks equipped with manual transmissions have a condition in which the clutch master-cylinder pushrod end that attaches to the clutch pedal pin can wear prematurely. the first noticeable effect of this wear…
On certain passenger vehicles equipped with an electronic throttle control system, the stopper for the accelerator pedal will prevent excessive movement of the accelerator position sensor. if the driver applies overly excessive force to…
Vehicle description: motor homes. the steering gear box IS mounted on a support located under the driver's seat floor. on motor home models, this support varies in height with the optional interior height. with 83 and 86 inch height…
Certain pickup trucks equipped with a tekonsha trailer hitch wiring harness and converter and distributed by gulf states toyota (texas, oklahoma, louisiana, arkansas, and mississippi). the circuitry used in the converter, which IS…
On certain heavy duty trucks equipped with meritor wabco pneumatic anitlock brake system (ABS) valve packages, the assembly bolts on these valve packages were not tightened correctly.