Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
On certain motor homes equipped with slide-out generators, certain generator slide-out ball screw actuator brake holding components are defective. the brake may not allow the actuator to hold the load in position with the power off. the…
On certain 4X4 pickup trucks, the rear axle flange weld to the axle tube could fatigue and allow the brake caliper assembly to rotate.
On certain heavy duty class 8 axle back vehicles, the telescoping steering shaft in some driving situations could bottom out and side load the steering gear input shaft whenever the adjustable steering column IS adjusted to the lower…
Certain school buses equipped with optional high back seats with 9" split sash, pushout windows fail to comply with the requirements of federal motor vehicle safety standard no. 217, "bus emergency exits and window retention and release."…
On certain motor homes and tour coaches, a 'check trans' warning light which IS required by allison transmission installation instructions was omitted. in the event the transmission shift selector malfunctions (looses power or sends…
Certain passenger vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." the owner's manual does not contain the proper headlamp aiming…
On certain travel trailers, an improperly reinforced drawbar was installed.
On certain motor homes, the independent movement between the chassis frame and the motor home body can cause the liquid propane (lp) gas tubing or the manifold pipe to split or crack.
On certain motor homes, an improperly mounted trailer hitch may have been installed on these motor homes. the trailer hitch may not have all the required fasteners attached to the motor home.
Mullins aluminum steering box (models A1 and A1P) and vega [style] 140 steering box (mul-140) assemblies. the screws in the worm shaft ball nut gear assembly were not adequately tightened and the interior of this product was not inspected…
On certain class c motor homes, the battery cable IS routed in a location that allows exposure to high exhaust manifold temperatures, which could damage the cables.
On certain passenger vehicles, the electric fuel pump runs at a rotational speed that could result in reduced lubrication of its internal components. over an extended period of time, wear-induced internal damage to the fuel pump could…
Vehicle description: sport utility vehicles that are equipped with an anti-lock braking system (ABS). the vehicles can experience extended stopping distances in certain types of braking events.
On certain sport utility vehicles that are equipped with an anti-lock braking system (ABS), the vehicles can experience extended stopping distances in certain types of braking events.
On certain motorhomes equipped with arvinmeritor wabco pneumatic anitlock brake system (ABS) valve packages, the assembly bolts on these valve packages were not tightened correctly.
Certain transit buses with an option for deceleration lights do not meet all the requirements of fmvss no. 108, "lamps, reflective devices, and associated equipment." the deceleration lights are located on the rear center of the bus…
On certain passenger vehicles, the pin at the end of the front suspension transverse link (lower control arm) could break where it IS mounted to the frame.
On certain motorcycles, the handle bar riser top clamp could allow excessive movement of the handle bars.
Equipment description: automotive battery charges, cat no. 48-59-0184 (all serial numbers). this charger was also packaged with the automotive 18 volt impact wrench kit, catalog number 9079-23 (serial numbers 241a40152001 thru…
On certain passenger vehicles, routing of the vehicle's front harness can allow it to come in contact with a rough edge, allowing abrasion. This could result in grounded circuits.
On certain passenger vehicles, the supplemental restraint system (srs) side impact air bag satellite sensors may be too sensitive to some lateral accelerations that are not caused by side impacts to the vehicle, such as forcefully slamming…
On certain low floor buses, the power steering hose was incorrectly installed.
On certain motor homes and motor coaches, the wiper arm attachment to the drive shafts can come loose causing the wiper system on that side to become inoperative.
Certain school buses equipped with regulation school bus seats (39" and 45") fail to meet the requirements of federal motor vehicle safety standard no. 222, "school bus passenger seating and crash protection." the seat may have tubing…
On certain motorcycles, the screws that attach the rear brake caliper to the rear swing arm were not tightened correctly during assembly. the screws could loosen during vehicle operation and eventually fall-out, allowing the rear caliper…
On certain trailers equipped with bendix SR-2, SR-4, and SR-5 trailer spring brake valve assemblies, the molded rubber face of the inlet/exhaust valve (i/e valve) component of the affected valves can separate from the valve's metal insert.…
On certain medium and heavy duty trucks, a brass fitting connects the double check valve to the brake relay valve. with certain inputs to the vehicle, the weight of the check valve on the fitting can cause the assembly to resonate. the…
On certain transit and school buses, a brass fitting connects the double check valve to the brake relay valve. with certain inputs to the vehicle, the weight of the check valve on the fitting can cause the assembly to resonate. the…
On certain trailers equipped with bendix SR-5 trailer spring brake valve assemblies, the molded rubber face of the inlet/exhaust valve (i/e valve) component of the affected valves can separate from the valve's metal insert. air can be…
On certain trailers equipped with bendix SR-2, SR-4, and SR-5 trailer spring brake valve assemblies, the molded rubber face of the inlet/exhaust valve (i/e valve) component of the affected valves can separate from the valve's metal insert.…