Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105,"Hydraulic and electric brake systems." the brake system warning indicator may not function as required by the standard.
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105, "hydraulic and electric brake systems." the brake system warning indicator may not function as required by standard.
On certain motorcycles, the mirror stem could fracture allowing the mirror to fall.
On certain recreational vehicles built on gm gmt610 rv chassis, due to a change in the fuel system of these chassis, increased pressure results in the fuel return line. the fuel return line IS used to provide a fuel tap for generators and…
On certain 1998-2002 35' and 40' buses and 1999-2002 29' buses, the installation of the air conditioner unit uses bolts along the edge of the housing for attachment. one specific bolt can be too close to the main power cable attachment.…
On certain school bus warning lamps, a static electricity discharge can occur during normal services or handling. this discharge can potentially initiate a chemical reaction of materials within the lamp which could cause the lens to…
In some of these sport utility vehicles, the diameter of the steering column intermediate shaft IS too small.
On certain model D30B motor homes built on a ford chassis, a plate, which IS used to support the spare tire, was inadvertently left off a number of these motor homes.
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105, "hydraulic and electric brake systems." the brake system warning indicator may not function as required by standard.
Certain passenger vehicles fail to comply with requirements of federal motor vehicle safety standard no. 209, "seat belt assemblies." the left and right front seat belt buckle/latch assemblies were improperly manufactured.
Aftermarket vector coffee makers packaged as greatland, model no. Vec216gt, and vector, model no. Vec216. the heating element inside the product can loosen causing it to come in contact with the plastic bottom layer which subsequently…
17 x 8 cragar S/S classic wheels manufactured between february 16, 2001, and february 18, 2002. the defect IS a weld that did not fully penetrate to the base metal. the wheel would develop cracks along the weld and could fail to hold the…
On certain MINI vans, passenger and sport utility vehicles, some of these vehicles have a driver's side air bag that may not deploy as designed. in addition, the air bag inflator could rupture.
On certain vans with a gross vehicle weight of less than 8,500 pounds, during a vehicle crash sufficient enough to deploy the safety belt pretensioner, the front safety belt buckles may not release after the vehicle crash, or alternately…
On certain MINI vans equipped with front fog lights,the fog light bulb socket may have been installed improperly.
On certain trailers equipped with hydraulic brakes, the breakaway brakes do not work.
Certain trucks equipped with trailer connections fail to comply with the requirements of federal motor vehicle safety standards (fmvss) no. 121, "air brake systems," and no. 108, "lamps, reflective devices, and associated equipment." the…
Aftermarket replacement american wire wheels, models superspokeii (p/n m0163540s-184) and superspoke (p/n m12121540s-200 & m32121540s-200). the steel spokes can pull out of the machined aluminum hub which will result in complete failure…
On certain motor homes, the brake hoses may not have been routed properly resulting in the hoses contacting the frame.
On certain fire chassis equipped with harrison hydra-gen generators. The tubing connecting the soft start to the generator pump can break away from the fitting and spray hydraulic fluid onto the exhaust.
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105, "hydraulic and electric brake systems." the brake system warning indicator may not function as required by the standard.
Certain sport utility vehicles fail to comply with the requirements of part 567, "certification." the incorrect gross vehicle weight rating (gvwr) data was printed on the certification regulation label. the gvwr IS incorrectly reflected…
The isb 4 cylinder crankshaft vibration dampers installed for use on chassis manufactured by workhorse and freightliner custom chassis. the affected engines were built from october 2000 through july 2001, and have an engine serial number…
Cummins isb 6 cylinder engines built from march 1998 through february 1999, and have an engine serial number within the range of 45480143 to 45818756 or 56436052 to 56561539. the lower alternator support brace or mounting hardware can…
On certain school bus warning lamps. A static electricity discharge can occur during normal services or handling. this discharge can potentially initiate a chemical reaction of materials within the lamp which could cause the lens to…
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105, "hydraulic and electric brake systems." the brake system warning indicator may not function as required by standard.
On certain motorcycles equipped with compufire brand series type voltage regulators, if damaged, the voltage regulator can become stuck in an open mode that allows battery voltage to flow back through the regulator.
Harrison hydra-gen generator pumps for use on fire trucks. The tubing connecting the soft start to the generator pump can break away from the fitting and spray hydraulic fluid onto the exhaust.
Model FX-3 motorcycle helmets manufactured prior to april 2002. the chin strap was sewn with one bar tack as apposed to two bar tacks. this does not comply with the requirements of federal motor vehicle safety standard no. 218…
Model FX-3 motorcycle helmets manufactured prior to april 2002. the molding process unique to this model requires injection of the liner into the shell which left weak spots in the front of the helmet. this does not comply with the…