Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
On certain passenger vehicles equipped with factory aluminum alloy wheels, the lug nut(s) may not secure the wheel properly to the hub assembly due to over-drilling of one or more of the five lug nut holes on the alloy wheel. if the…
On certain converter dollies equipped with bendix ec-30t electronic control units (ecu). if the trailer-mounted ABS warning lamp circuit experiences an electrical short and the short IS not repaired, the high side power switch inside the…
On certain trailers equipped with bendix ec-30t electronic control units (ecu). if the trailer-mounted ABS warning lamp circuit experiences an electrical short and the short IS not repaired, the high side power switch inside the ecu that…
Certain passenger vehicles, the torque applied to the joint screw between the steering wheel and the steering column was not certified.
On certain trailers equipped with bendix ec-30t electronic control units (ecu). if the trailer-mounted ABS warning lamp circuit experiences an electrical short and the short IS not repaired, the high side power switch inside the ecu that…
On certain motorhomes equipped with tuthill independent front suspensions, the defect IS insufficient tightening torque of the steering knuckle carrier bolt that may result in separation of the steering knuckle from one of the control arms.
My 2003 mbii & mbiv school buses built on ford E-350 & E-450, gm 3500 chassis, and manufactured between august 25 and september 17, 2003. these buses are equipped with beam's industries seat belts. the metal frame of the seat belt buckle…
On certain trailers equipped with sealco spring brake control valve assemblies incorporated in arvinmeritor axles, part no. 110800, there IS a recessed area on top of the valve in which a brass guide pin fits down inside the body of the…
On certain buses, air lines are connected so when a single service system failure occurs, the bus does not comply with fmvss 121 S.5.7.1 and S5.7.2.
On certain motorhomes certification tags were omitted on the cloth covered front and rear brake line assemblies.
On certain heavy duty class 8 trucks assembled by volvo trucks, the transmission may go into forward gear without the driver first pressing down on the brake pedal.
On certain passenger vehicles, the passenger detection function of the passive occupant detection system (pods) may become disabled.
Certain passenger and sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 207, "seating systems." one or both front anchor tabs for the front bucket seats are not engaged in the floor…
On certain trailers equipped with sealco spring brake control valve assemblies incorporated in arvinmeritor axles, part no. 110800, there IS a recessed area on top of the valve in which a brass guide pin fits down inside the body of the…
On certain school buses, the power cables that run from the starter to the power distributor unit may chafe against the bottom corner of the front floor panel, resulting in an electrical short.
On some motorcycles, certain frame welds do not meet manufacturing specifications. high loads created when riding on rough road surfaces or through potholes can cause the affected welds to crack.
On certain trucks equipped with allision transmissions, the transmission can drop out of the vehicle.
On certain passenger vehicles, fuel leaks may develop at the fuel distributor assembly because of quality deviations.
On certain sport utility vehicles, the affected vehicles may be missing the gross vehicle weight rating (gvwr) and gross axle weight ratings (gawr) on the certification label as required by part 567.4(g)(3) and (G)(4).
Ce model school buses which fail to comply to federal motor vehicle safety standard no. 221, school bus body joint strength. the roof top sheet may be improperly located, reducing the material edge distance at the rivet line.
On certain buses equipped with cummins electronic control modules on the L10G engines, the ecm does not have the ability to detect a throttle fail-safe engine shutdown command. this could result in an unanticipated, uncommanded open…
On certain pickup trucks, the pitman arm to steering gear retaining nut was not fully tightened to the required specification.
On certain trailers equipped with sealco spring brake control valve assemblies incorporated in arvinmeritor axles, part no. 110800, there IS a recessed area on top of the valve in which a brass guide pin fits down inside the body of the…
Certain motor home chassis fail to comply with the requirements of federal motor vehicle safety standard no. 105, "hydraulic and electric brake systems." the brake system warning indicator may not function as required by standard.
On certain motorhomes built on workhorse chassis, the hydraulic hose operating the leveling jack system was routed so it places the hose too close to the engine exhaust. the hot exhaust can cause the hydraulic hose to melt or abrade…
On certain trailers equipped with sealco spring brake control valve assemblies incorporated in arvinmeritor axles, part nos. 110700 and 110800, there IS a recessed area on top of the valve in which a brass guide pin fits down inside the…
On certain model passenger vehicles, as a result of improper welding of the seat rail assemblies, one side of the seat may not fully lock into the set position. under extreme acceleration or deacceleration conditions, this could cause a…
On certain trucks equipped with meritor 15X4 front brakes and dana e1200 steer axle, the left brake cannot fully apply or it would become stuck and not release.
On certain motorhomes equipped with tuthill independent front suspensions, the defect IS insufficient tightening torque of the steering knuckle carrier bolt that may result in separation of the steering knuckle from one of the control.
On certain trailers equipped with sealco spring brake control valve assemblies incorporated in arvinmeritor axles, part nos. 110700 and 110800, there IS a recessed area on top of the valve in which a brass guide pin fits down inside the…