Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
This campaign involves certain marauder model motorcycles equipped with california evaporative emissions equipment. when a motorcycle IS parked after city driving in heavy traffic, under some conditions, elevated pressure in the fuel tank…
Certain pickup trucks fail to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." an area on the rear pillar where the rear seat belt upper anchor IS attached may not…
Certain motor coaches fail to comply with the requirements of federal motor vehicle safety standard no. 121, "air brake systems." these buses were manufactured without the check valve, which protects the front service brake reservoir.
On certain school buses built with vandale lock systems, the system does not provide an audio sound to warn the driver that the emergency door IS locked while the vehicle IS in operation.
Certain MINI trailers have inadequate welds to the tongue and frame assembly. this could cause separation of the tongue assembly from the frame.
Certain trucks fail to conform to the requirements of federal motor vehicle safety standard no. 120, 'tire selection and rims for motor vehicles other than passenger cars.' the tire pressure was omitted from the vehicle's certification…
On certain passenger vehicles originally sold in or currently registered in the states of connecticut, delaware, illinois, indiana, iowa, kentucky, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey…
On certain passenger vehicles, the camshaft position sensor may melt resulting in a burning smell and visible smoke, which may subsequently lead to the melting of the camshaft cover and the camshaft position sensor wire harness.
On certain passenger vehicles equipped with 8 and 12 cylinder engines, the digital engine management control (emc) units were not produced according to specifications.
On certain sedan and wagon model vehicles, the left front bolt that retains the forward part of the driver's seat to the seat slide rail may loosen. if the seat slide rail bolt loosens, it will eventually fall out, and the seat may…
On certain pickup trucks, the frame may have a center rail section flange that was not formed properly.
On certain vehicles equipped with curtain shield air bags (csa), one or both of the curtain air bags may be twisted near the inflator due to improper assembly.
On certain passenger vehicles, the flat tire monitoring system has not been correctly programmed. in the event of a flat tire, an audible signal will not sound to alert the driver to a flat tire.
Certain sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 201, "occupant protection in interior impact." during testing, the free motion head form registered a measurement marginally…
On certain school buses chassis equipped with caterpillar engines and hydraulic brakes. a braided ground strap for the starter may rub on a steel chassis brake line potentially causing a fluid leak.
On certain passenger vehicles, the battery cable fasteners at the bulkhead stud may not have been properly tightened.
Certain motorcycles, a significant quantity of oil lubricant can leak on to the rear wheel and tire from the oil cooler.
On certain fifth wheel and travel trailers equipped with samsung microwave ovens, models mr1031wb, mr1032bb, mr1033sb, mr1351wb, and mr1352bb, the microwaves were produced with a defective panel. an electrical short can occur between…
On certain sport utility vehicles equipped with 3.7L engines only, two valve cover studs may interfere with the fuel injector and alternator wiring harnesses.
On certain convertible model vehicles, the left hand rear seat belt retractor bolt may not have been properly tightened.
On certain passenger vehicles, the front shoulder belt adjustable turning loop (atl) bolts may not have been properly tightened.
On certain passenger vehicles, a spot welding operation for the rear floorpan reinforcement may not have been performed.
Certain passenger vehicles equipped with power adjustable seats may have been inadequately welded.
On certain motor coaches, the front lower radius rod mounting bracket components may not have been welded sufficiently.
Certain police, commercial, and passenger vehicles sold to fleets typically input higher loads into the vehicle chassis overloading the wheel bearings and axles.
On certain pickup trucks and sport utility vehicles equipped with 6.0L diesel engines, the engine ground stud that attaches the negative battery terminal eyelet to the engine block may be loose.
On certain passenger vehicles equipped with skyview roofs, the glass for the roof may not have been quenched properly after the forming process, resulting in temper imbalance.
Certain motorhomes fail to comply with the requirements of federal motor vehicle safety standard no. 135, "brake systems." the antilock brake system (ABS) lights are not visible on the instrument cluster of the dash.
Certain scooters may have a defective engine mount that could separate without warning during normal use. the welded seam in the tubing may separate allowing the engine to shift out of normal operating position.
Certain motorhomes fail to comply with the requirements of federal motor vehicle safety standard no. 104, 'windshield wiping and washing systems.' the windshield wiper assembly was installed without proper support allowing the wiper…