Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Certain two-seater coupes fail to comply with the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment." the front side marker light, that IS behind the front wheel, needs to…
Certain passenger vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 124, 'accelerator control systems.' if one of the two accelerator pedal return springs fails and the temperature IS -22 degrees f…
On certain single axle brush chipper trailers, fatigue and cracks can occur in the tongue weldment.
On certain motor homes, a circuit design resulted in a 12.1 amp circuit draw in the brake light circuit when it IS protected by a 10 amp circuit breaker.
Certain trucks, sport utility vehicles, and vans equipped with bosch hydro-boost brake assemblies, the hydraulic brake booster pressure accumulator may crack and separate from the hydro-boost assembly during normal operating conditions.
Certain trailers, equipped with truck-lite brand model 44,40 or 30 stop/tail light and front/rear side marker lights with no reflex lens or reflective material, fail to comply with the requirements of federal motor vehicle safety standard…
Certain ic ce 2005 school buses manufactured between april 27 and october 13, 2004. the locknut that secures the hydraulic brake pivot bolt may not be torqued properly.
On certain transit buses manufactured with detroit diesel series 50 engines, the turbocharger compressor wheel can break, resulting in shaft imbalance and lubricating oil passes into the exhaust system.
On certain drill rigs and well service rigs equipped with bendix antilock brake system (ABS), the air brake valving installed on the drive axles of certain tri-drive axle IS inadequate and it does not have the correct air valve…
On certain transit buses equipped with arvinmeritor urresko tie rod clamps, heat treatment of clamps created a surface hardness that could lead to a fracture of the clamps.
On certain minivans and sport utility vehicles, the steering column may be incorrectly assembled, which could result in a loss of steering control.
Certain my 2003 thru 2005 blue bird micro bird and conventional school buses. these buses do not have the tire load range on both the tire information label and certification decal as required by federal motor vehicle safety standard no.…
Certain sport utility vehicles fail to comply with the requirements of federal motor vehicle safety standard no. 212, 'windshield mounting.' the windshield urethane bead may not have adhered to the body in certain areas during the cure…
On certain sport utility vehicles, the fuel tank filler tube inlet check valve may not fully close at the end of refueling. this could allow some fuel to escape from the vehicle filler neck.
On certain heavy duty class 8 fire trucks equipped with arvinmeritor urresko tie rod clamps, heat treatment of clamps created a surface hardness that could lead to a fracture of the clamps.
On certain heavy duty class 8 trucks equipped with bendix automatic brake systems (ABS), the brakes may have a system fault that may not be detected by the ABS electronic control uunit (ecu) and therefore will not generate an ABS warning…
On certain heavy duty class 8 trucks equipped with arvinmeritor urresko tie rod clamps, heat treatment of clamps created a surface hardness that could lead to a fracture of the clamps.
On certain heavy duty class 8 trucks equipped with arvinmeritor urresko tie rod clamps, heat treatment of clamps created a surface hardness that could lead to a fracture of the clamps.
Certain passenger vehicles with four or five doors and originally sold in or currently registered in connecticut, delaware, illinois, indiana, iowa, maine, maryland, massachusetts, michigan, minnesota, missouri, new hampshire, new jersey…
On certain transit buses equipped with detroit diesel series 50 engines, the turbocharger can fail allowing lubricating oil to enter the exhaust system.
On some motorcycles, certain frame welds do not meet manufacturing specifications. high loads created when riding on rough road surfaces or through potholes can cause the affected welds to crack.
On certain passenger vehicles, the interlock operation of the ignition switch may not function properly, making it possible to turn the ignition key to the "off" position and remove the key without shifting the transmission to park.
On certain motor homes, the 120-volt shore power cord was wired without a circuit protection device.
On certain passenger vehicles, the brake light switch may become misadjusted if an upward/rearward force IS applied to the brake pedal. if this should occur, the brake light switch will not function properly, causing the brake lights…
On certain sport utility vehicles and pickup trucks, the speed control deactivation switch may overheat, smoke, or burn.
Certain passenger vehicles have a non-functioning button with the words "passenger air bag off" etched into it. this button IS located, along with an led light, on a console adjacent to the sun roof. this non-functioning button does not…
Certain passenger vehicles have a non-functioning button with the words "passenger air bag off" etched into it. this button IS located, along with an led light, on a console adjacent to the sun roof. this non-functioning button does not…
Certain transit buses fail to comply with the requirements of federal motor vehicle safety standard no. 217, "bus emergency exits and window retention and release." the striker plates at the bottom of the emergency pushout windows can…
Certain girardin minibus my 2004 and 2005 mb II and mbiv ford diesel school buses equipped with optional bbx (battery box) manufactured between may 14, 2004 and february 9, 2005. the electrical cables (p/nos. 27Df01 and 27df3001) between…
Certain motorcycles equipped with combined-brake systems have a proportioning control valve (pcv) that mechanically proportions brake force when the rear brake IS applied. a seal in some pcvs IS improperly shaped, and brake fluid leakage…