2007 BMW 135I Coupe

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
• 10199287CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10198894CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
• 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
• 10181214Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
• 10170574SERVICE ACTION: N54T ENGINE - INSPECT AND REPLACE INJECTOR(S). The piezo-type fuel injectors may cause a rough running at start-up or rough running while at idle.
• 10160287TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
• 10160244TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
• 10152314Door Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM door lock status due to voltage variations
• 10151335Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
• 10151323ELV Does Not Release. The customer complains of a no-crank, no-start situation. The condition may be intermittent. The ELV (Electric Steering Lock) warning is shown in the Instrument Cluster.
• 10151170N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
• 10151119SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
• 10151115SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
• 10151081"PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. This Service Information bulletin supersedes SI B13 14 10 dated July 2013. SUBJECT Voluntary Emissions Recall Campaign 10E-A02: N54 Inspection and Replacement of Injectors. The piezo injectors may cause misfire faults with erratic engine operation. AFFECTED VEHICLES This Emissions Recall involves E60, E61, E71, E82, E88, E90, E92, and E93 vehicles with N54 engines which were produced from 04/02/2007 through 11/30/2008. In order to determine whether a specific vehicle has had this Emissions Recall Campaign completed or is affected by this Recall Campaign, it will be necessary to utilize the ""Service Menu"" of DCSnet (Dealer Communication System) or the Key Reader. Based on the response of the system, either proceed with the corrective action or take no further action. Copy of the customer letter is attached."
• 10151079SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
• 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
• 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
• 10150964?VOLUNTARY EMISSIONS RECALL CAMPAIGN 16E-A02: PROGRAM CONTROL UNITS (DME OBD) Please perform the procedure outlined in this Service Information on all affected vehicles before customer delivery or perform the procedure the next time the vehicle is in the shop.
• 10150389Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
• 10150385"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
• 10150334"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
• 10150330"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
• 10150265Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
• 10150264"The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding."
• 10150224"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
• 10150173"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
• 10150133In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
• 10150131"Enabling and Replacing New OC3 Seat Mat. The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it."
• 10150130The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
• 10150100The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (?wet?) with fuel, while the injector tips are covered with a layer of carbon deposit.
• 10150099N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
• 10150096N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
• 10150065"BMW NA has agreed to extend the emissions warranties of the turbocharger's wastegate to: ??8 years or 82,000 miles, whichever occurs first, as determined from the vehicle's original in-service date select the ""Vehicle Comment"" button to display the extended coverage information. The terms of the original New Vehicle/SAV Limited Warranty and applicable emissions warranty still apply. BMW NA will not provide warranty coverage to any Settlement Class Member's vehicle containing modifications or alterations to the turbocharger or its wastegates (software, hardware or otherwise), or evidencing other conditions not normally covered under the original New Vehicle/SAV Limited Warranty or applicable emissions warranty. Modifications excluded from warranty coverage include any aftermarket parts that affect the turbocharger system, or if there are other conditions that would normally exclude it from warranty coverage."
• 10150035Voluntary Emissions Recall Campaign 10E-A02: N54 Inspection and Replacement of Injectors. The piezo injectors may cause misfire faults with erratic engine operation.
• 10149616"Safety Belt Extender ""Handover"" Fails to Deliver the Belt to the Customer. The customer states that the seat belt extender ""handover"" on the front driver's or passenger side failed to deliver the belt. One or more of the following situations may apply: * The safety belt extender extends but the belt slips off. * The ""hand"" on the extender fails. * The safety belt is twisted. * The extender will not operate and makes noise while extending. S One or more of the following causes may apply: 1. The safety belt is incorrectly positioned. 2. The ""hand"" on the extender has mechanically failed. 3. The safety belt slips off the ""hand"" due to excessive resistance from the seat belt reel, not allowing the belt to extend properly. The seat belt is twisted. 4. The safety belt slips off the ""hand"" due to the belt material being excessively worn. 5. The safety belt extender fails to extend or retract intermittently due to FRM (Footwell Module) software. 6. The safety belt extender is noisy or inoperative, due to a communication problem or incorrect power or ground."
• 10149613In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
• 10149595Erroneous Brake Pad Replacement Message. The Dynamic Stability Control module (DSC) calculates the brake pad replacement intervals based on information from the front and rear axle brake pad wear sensors. When replacement of the front and or rear brake pads is necessary, the DSC control module triggers an indicator lamp located in the vehicle's instrument cluster. However, the brake pad indicator lamp may be illuminated although a replacement of the brake pads is not necessary. Additionally, one or both of the following fault codes may be stored in the DSC control module: * 5DE0 Brake-pad wear: plausibility, front axle * 5DE1 Brake-pad wear: plausibility, rear axle CAUSE DSC software error
• 10149589"N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop. During the course of diagnosis, the spark plugs, removed from the misfiring cylinders after the problem was reproduced, are found to be soaked (""wet"") with fuel, while the injector tips are covered with a layer of carbon deposit. Possible cause: high-pressure injector failure (leakage or incorrect spraying pattern) due to internal wear or unfavorable stock of tolerances IMPORTANT: For comprehensive N54 drivability diagnostics, always refer to the ""N54 Engine Diagnostic Fault Tree"" file (the current version ""02_14_13"" is found as a PDF attachment to SI B12 55 06)."