Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The involved vehicles were not equipped with rear side reflectors, rear side marker lamps, front and rear clearance lamps and rear identification lamps. This constitutes a non-compliance to federal motor vehicle safety standard no. 108…
The involved tires failed to meet the minimum endurance requirements of federal motor vehicle safety standard no. 109, "new pneumatic tires". These tires failed when tested under adverse conditions of overload, under-inflation and…
The involved tires fail to conform to federal motor vehicle safety standard no. 109, "new pneumatic tires", due to distortion and separation in the tread area, which can occur while the tire IS in service and subjected to operating…
These tires failed to meet the endurance requirements of federal motor vehicle safety standard no. 109, "new pneumatic tires". Failure occurred because these tires developed tread separation of the structural components in the bead area of…
On the involved vehicles, the electrically powered windows may be operated when the ignition key IS in the "off" position or IS removed from the ignition switch. This constitutes a non-compliance with federal motor vehicle safety standard…
On the involved vehicles, one or both of the front brake caliper bolts may break. This could allow the broken portion of the bolt to drift into the adjacent rotating wheel spokes. Should both caliper bolts break, the inner caliper half may…
The involved vehicles fail to conform to federal motor vehicle safety standard no. 217, "bus window retention and release". The rear door glass may have been installed with a rubber gasket which may provide marginal retention.
The involved vehicles were equipped with headlights that fail to meet the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment". Also, the tail, stop and license plate assembly…
On the involved vehicles, the ABS plastic l.p. Gas bottle shield IS attached with a nylon covered rubber cord with plastic coated metal hooks at each end. These metal hooks may chafe against the aluminum l.p. Gas bottle, eventually wearing…
On the involved vehicles, the headlights fail to meet the requirements of federal motor vehicle safety standard no. 108, "lamps, reflective devices and associated equipment". Headlights do not provide sufficient illumination, brake light…
On the involved vehicles, corrosion could develop in the cruise control system servo unit. Consequently, the cruise control system may not respond to attempts to release it by depressing the brake pedal, but could begin to accelerate the…
The involved vehicles do not conform to federal motor vehicle safety standard no. 121, "air brake systems". The incorrect brake linings were installed on these vehicles. This could lead to increased stopping distances.
The involved vehicles may not comply with federal motor vehicle safety standard no. 126, "truck-camper loading". The vehicle owner"s manual failed to provide specific center of gravity and dry weight information. Without this information…
On the involved vehicles, the incorrect steering linkage assembly may have been installed. As a result, the right-hand steering tie rod might interfere with the intermediate rod. This could cause the connection to fail due to excessive…
On the involved vehicles, the incorrect fuel hose pipe was installed. Consequently, the needed special reinforcement, used to help prevent rupture of the hose and spillage of fuel resulting from an impact from the side, was omitted. This…
On the involved vehicles, a sudden loss of pressure from the wheel/valve assembly could occur due to splitting of the valve rubber.
On the involved vehicles, the steering universal shaft assemblies may have been improperly manufactured. As a result, the assembly could fail.
A "speed nut", which retains the steering column boot to the toeboard, can cut through the steering column.
The involved tires fail to meet the high speed requirements of federal motor vehicle safety standard no. 109, "new pneumatic tires". These tires failed during the high speed test because of tread separation.
The stub ends of the axle housing may not have been properly manufactured to specifications. These stubs would be of inadequate strength and could fracture. Complete fracture would cause the front wheel, hub, and brake assembly to detach…
The rated capacity of the suspension system may be inadequate for normal in-use loading. Consequently, the springs may sag and the wheels could break.
The rear axle suspension u-bolts on the involved vehicles may fail. Should two or more u-bolts fail, the drive axle(s) can separate from the vehicle chassis.
The involved vehicles may not comply with federal motor vehicle safety standard no. 110, "tire selection and rims". The tire pressure placards incorrectly specify the front tire pressure for maximum load conditions. As a result, tires…
The involved vehicles fail to conform to federal motor vehicle safety standard no. 301, "fuel system integrity". In a 30 m.p.h. Frontal crash barrier test, the fuel line broke, allowing excessive fuel leakage due to dislocation of the…
The front wheel spindle on the involved vehicles may crack in service. Spindle stem separation could occur due to failure of the stem at the inner bearing fillet location.
The involved tires may develop flex cracks in the upper sidewall area while in service. These cracks are a result of use of the wrong fabric in one of the body plies.
The involved tires may not meet the requirements of federal motor vehicle safety standard no. 119, "new pneumatic tires for vehicles other than passenger cars". As a result, the tread could separate from the carcass in the shoulder area of…
The involved vehicles may have been equipped with aluminum grab handles. These handles can crack through the upper mounting hole and eventually fail.
The hoses on the involved vehicles may not have been properly installed. As a result, air leakage could occur. This constitutes a non-compliance to federal motor vehicle safety standard no. 106, "brake hoses". Complete failure will…
The pin box support members on the involved vehicles may gradually distort and fail. This could cause a decrease in towing stability.