Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
On the involved vehicles, the mounting tabs used to mount the fifth wheel assembly to the chassis in place of the normal continuous angle construction could crack. These cracks can develop in the areas where the tabs are welded to the side…
The involved vehicles were built with aft-of-axle fuel tanks which were not authorized by light truck engineering. As a result, these vehicles fail to conform to federal motor vehicle safety standard no. 301, "fuel system integrity", due…
The involved vehicles are equipped with air conditioning units which contain blower motor resistor wires which are improperly positioned. As a result, under certain conditions the polypropylene case material could become overheated and…
The involved vehicles may contain air conditioners which have blower motor resistor wires which were improperly routed too close to the blower housing wall. As a result, the blower motor could become jammed and, if the blower switch IS in…
The involved vehicles are in non-compliance with federal motor vehicle safety standard no. 124, "accelerator control systems". The throttle cable plastic sleeve on these vehicles, which IS attached to the firewall, could break at the…
On the involved vehicles, the manual steering gears may contain steering gear recirculatory balls that could fracture. This fracturing IS a result of improper heat-treatment during manufacture and can eventually cause increased steering…
The involved vehicles are in non-compliance with federal motor vehicle safety standard no. 207, "anchorage of seats", due to the possibility for the front seats to separate from the seat adjuster tracks. The separation may occur because…
The involved vehicles fail to comply with federal motor vehicle safety standard no. 207, "anchorage of seats", due to possible failure of the seat post attachment at the floor in the event of an accident. These vehicles have oversized bolt…
The l.p. Gas shutoff valves on the involved vehicles may have been damaged during installation of the refrigerator. This could cause gas leakage into the refrigerator compartment.
On the involved vehicles, the vacuum line connecting the carburetor and the thermo valve may have been improperly installed. This condition may prevent the throttle linkage plate from returning to its idle position.
The involved tires fail to meet the endurance requirements of federal motor vehicle safety standard no. 119, "new pneumatic tires for vehicles other than passenger cars". These tires may develop cracks at the center groove of the tread…
On the involved vehicles, the threaded studs which secure the l.p. Tank mounting system could fail. Consequently, the l.p. Tank may drop to ground.
The two piece parallel arms may contain defective welds in both the right and left arms of the lift gate.
The involved hubs may develop cracks in the area of the wheel mounting flange. Eventually, the hub could fail causing the flange along with the wheel and tire to become disengaged from the vehicle and roll in an uncontrolled manner.
The involved vehicles were assembled with front axle u-bolts which were fabricated from defective raw material and could crack. This could lead to failure of the u-bolts and separation of the steering axle from the truck chassis.
The involved tires may not comply with federal motor vehicle safety standard no. 109, "new pneumatic tires", due to an undercure condition in the tread area. Continued use could result in tread chunking or tread separation, leading to air…
The fuel tubes (fuel tank to pump) on the involved vehicles may be routed such that tube to underbody reinforcement flange interference may result during vehicle operation. Tube abrasion caused by such interference may result in fuel…
The columns may contain steering shafts in which the steering column coupling roll pin retaining notch was machined too deep. This may cause the steering wheel shaft to become disengaged from the rest of the steering assembly.
The electronic engine control (eec) wiring harness may be misrouted. This misrouting may cause the speed control servo arm to be held open due to mechanical interference when the speed control IS engaged. This causes a partially open…
These vehicles may not conform to federal motor vehicle safety standard no. 120, "tire selection and rims for motor vehicles other than passenger cars". The existing certification labels show gross vehicle weight as 2680 lbs. Rather than…
The brass compression coupler used to join two halves of liquid propane gas manifold between the frame members below the floor, can be the source of a liquid propane gas leak when subjected to over-the-road environmental conditions.
The involved vehicles do not conform to federal motor vehicle safety standard no. 108, "lamps, reflective devices, and associated equipment". These vehicle do not have the required tail lamps, stop lamps, license plate lamp, reflex…
The involved vehicles do not conform to federal motor vehicle safety standard no. 121, "air brake systems". These vehicles do not meet the 0.550 second brake release timing requirement.
A deficiency exists in the welds securing the rear spring insulator bracket to the axle housing. This IS due to improper positioning of the weld, in relationship to the bracket and axle housing. Failure of the welds would cause separation…
The involved vehicles do not conform to federal motor vehicle safety standard nos. 207, "seating systems", and 210, "seat belt assembly anchorages". Vehicles equipped with viking t-bar seats have the seat belt anchorage located under the…
The fuel blind plug on the carburetor may fail due to improper sealing. This could result in fuel leakage and an engine compartment fire, if fuel reaches the heated components.
The involved vehicles do not conform to federal motor vehicle safety standard no. 106, "brake hoses". These front hydraulic brake hoses may fail under pressure of brake application due to use of improperly processed material. Partial loss…
An interruption of the main electrical power feed circuit from the battery and alternator may occur due to separation of a terminal connection in the wiring circuit. The terminal end of the power feed wire coming from the compartment may…
The rear wheel mounting bolts on the affected vehicles, are brittle and therefore may fracture. This brittleness IS due to improper heat treatment during manufacture. If the bolts break, the tire and wheel assembly may separate from the…
The involved vehicles may have been equipped with cast aluminum wheels with inadequate lug nut counterbore depths. This condition may not provide sufficient lug nut thread engagement. The lug nuts may loosen and fall off, allowing the…