Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
On certain vehicles, two fuel line brackets were incorrectly positioned, allowing the fuel line to come into contact with the left hand front brake jounce hose. Contact with the fuel line, which has a metal outer shield, could cause…
Due to computer input error which resulted in an incorrect build schedule, some vehicles were shipped without the required exhaust system heat shields. When the vehicle IS idled over an extended period of time, a missing exhaust heat…
On certain vehicles the steering gear box was installed using mounting bolts which are too long in relation to the available hole depth in the steering gear box.
Vehicles may not conform to federal motor vehicle safety standard no. 217, "bus window retention and release". Certain vehicles may have gone through production without the deactivation of the key lock in the rear door.
On certain vehicles there may be a gradual loosening of the rear sprocket bolt(s) and a decrease in the clamping force necessary to maintain a secure attachment of the rear wheel sprocket to the wheel.
An incorrect rim flap has been installed which allows the inner tube to protrude through the rim valve opening and cause a chafing condition. This could lead to rapid loss of air from the tire.
On certain vehicles, lamp and grommet rotation may cause the rear combination lamps to fail to comply with federal motor vehicle safety standard no. 108, "lamps, reflective devices and associated equipment". Lens rotation could result in…
Under particular climatic conditions, engine hesitation may occur when restarting after vehicle IS parked for a short period of time. This hesitation IS caused by gasoline vaporization in the carburetor.
The auxiliary heater"s exhaust pipe IS mounted in a downward position toward the ground.
A resilient washer may drop out, causing the bolting attachment of the air reservoir to the frame to become loose. Due to vibration, the bolt could eventually wear through, allowing the reservoir to drop down on either end. This condition…
Certain vehicles may have been equipped with the wrong size wheels. These wheels have a lower load carrying capacity which could lead to trailer overloading, rim material separation in the bead seat area, loss of air and possible…
The front brake assemblies installed on certain vehicles may have been incorrectly assembled. This defect will result in a degraded brake efficiency.
When wiper blades are frozen to the windshield and the wiper motor IS turned on, the right-hand wiper pivot may become bent. The plastic bearing, which IS a snap-on device fitting over the ball joint on the drive motor, may pull off the…
When subjected to the extremely high temperatures that can occur in the engine compartment, the damper sleeves which cover the return springs of the accelerator control system can deform and prevent their returning the throttle to idle…
Steering arms on involved vehicles, identified by the heat code "E14", may have received improper heat treatment. This condition could cause the steering arm to crack or break.
Vehicle does not conform to federal motor vehicle safety standard no. 105, "hydraulic brake systems". The brake warning light may not activate when the ignition key IS rotated between the "on" and "start" circuit checking positions.
Vehicles may not conform to federal motor vehicle safety standard no. 120, "tire selection and rims for motor vehicles other than passenger cars". On some vehicles the tire and rim size designation and the cold tire inflation pressure were…
Vehicles may not conform to federal motor vehicle safety standard no. 122, "motorcycle brake systems", which requires that each of the mopeds be equipped with two independently activated service brake systems. On the involved vehicles, the…
Due to a combination of disc brake pad wear and turn stop wear on certain vehicles, there may be an increase in brake pedal travel and a reduction in front braking effectiveness following a full turn. Also, a frame crack could develop and…
Certain vehicles were produced with wheel assemblies that may have cracks near the bolt holes in the wheel disc. During vehicle use, the cracks could gradually increase and result in partial or complete separation of the wheel and tire…
In the process of assembly, which includes tapping into the chassis stop light switch circuit, a break occurred in the circuit that provides current to the emergency braking hydraulic pump motor. This causes the hydraulic service brake…
The optional accessory beds may fall to floor when used, due to fatiguing and breaking of the bed support brackets.
There IS a possibility that the use of a non-specified material in the plastic piston of the master cylinder assembly may allow a greater degree of water absorption than intended by harley davidson.
Heat generated by catalytic converters may cause deterioration of hydraulic brake hoses on certain vehicles. Brake hose may fail, resulting in loss of hydraulic fluid from the dual hydraulic system.
The adjusting screw, which mounts through a fork lock lever assembly into the fork lock itself, may not be fully and securely engaged because the screw may not be long enough. This may allow the fork pin to drop and accidentally engage the…
The bolts that clamp the mor/ryde suspension beam and lower mounting plate to the axle may break as a result of misalignment of the bolts due to non-parallel surfaces of the upper beam plate and the lower bottom plate. Another contributing…
On certain vehicles the brake linings could separate from the brake shoes due to insufficient brake lining bonding.
Stop lamp switches on certain vehicles may have been contaminated with oil, which could degrade the contacts and result in a loss of stop lamp function.
The studs which fasten the steering and tie rod arms to the steering knuckle may fail. This IS due to an improper key fit which could cause an unusual strain on these studs.
The hinge and roller assemblies supporting the rear of the sliding side door may be subject to failure as a result of processing deficiencies in the aluminum hinge body.