Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
The 12 mm spacer used on the rear seat belt anchorage bolts may affect anchor bolt load capacity and fail to comply with fmvss 210, seat belt assembly anchorages.…
The engine air cleaner plastic trim cover could detach from the air cleaner assembly and fall forward on the exhaust manifold. consequence of…
The lead wires connecting the battery to the starter solenoid, and the solenoid to the starter, may be misrouted and damaged. consequence of…
A malfunction may occur in the air suspension electrical circuitry.
Fuel hose may be damaged due to too much pressure in crimping the hose end fitting. consequence of…
Carbon monoxide produced by the auxiliary power generator, when used for prolonged periods of time may enter the motorhome interior.…
The steering arm may crack after repeated full-lock turns. consequence of…
The electrical cable between the starter and the alternator can rub against the brake fluid pipe attached to the left inner wheelhouse in the engine compartment.…
The seat belt may not remain snug after adjustment. consequence of defect: in the event of a sudden stop or accident the seat belts may not…
The fuel system may leak at the throttle body injection fuel feed pipe connection. consequence of…
Circuit breakers are not at sufficient ratings to protect high side tolerances, some wiring harnesses are not adequately secured to prevent chafing and no provisions were made for complete disconnection of all electrical…
Hairline cracks may occur in one or more of three weld areas: front suspension interface plate at the bottom frame structure, rear suspension termination points of the transverse link tower outboard gusset, or rear axle mounting…
Front seat belt retractors may not properly lock during sudden heavy brake application or impact due to the interference of two positioning tabs.…
The air brake hose leading to the front axle spring brake chambers may be 1.5 inches shorter than the specified length or are connected to air tanks mislocated up to 1.5 inches.…
The cruise control vacuum solenoid valves may malfunction at any time the engine IS running and the cruise control IS engaged and cause unexpected engine acceleration.…
The tire placard label on the left front door may have been printed with an error which specifies a higher maximum loading than IS allowed.…
Incorrect rear dual wheels may have been installed, making the wheels subject to crack. consequence of…
The steel wheel rims may crack and break. consequence of defect: broken wheel rims could cause the driver to lose control of the vehicle and…
Brake master cylinders may have improperly anodized internal surfaces causing accelerated wear of a piston seal. consequence of…
One of the three steering gear to frame bolts may not have been tightened to the required specification. consequence of…
Metal bushings for the cruise control linkage are subject to corrosion due to weather conditions. Also, there IS not enough clearance between the bushings and the shaft; and the linkage points were not lubricated. Thus…
Looseness may develop at the attachment (ball joint) of the drag link to the steering arm due to an insufficiently tightened retaining nut. This can wear the steering arm hole.…
Impure lubricating grease used in the headlight switches could contaminate one or more contact points. Operation of the headlights could be delayed or not light when the switch IS turned on or when the dimmer switch IS operated.…
A steel tube that delivers air to the front axle air brake chamber can contact the front shock absorber. consequence of…
Certain trucks do not comply with fmvss 108, "lamps, reflective devices and associated equipment." the trucks were assembled without the roof marker lamps.…
The rack and gear type latch assembly of the emergency doors can be overstressed by misuse of the inside door handle, making the gears subject to failure.…
The hub area of the wheels may not be structurally sound and thus subject to fracture. consequence of…
Seam leaks may develop in the 70 gallon aluminum fuel tank, allowing gasoline to spill on the ground. This IS due to poor seam welding.…
The throttle shaft of the carburetor may crack and eventually break at the threaded hole for the throttle plate connection due to excessive vibration of the throttle shaft.…
The auxiliary fuel tank IS subject to overfill and pressure buildup. consequence of…