Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Rear brake relay valve control line was connected to the secondary double check valve, rather than the primary one. consequence of…
A part of the steering gear housing which attaches to the frame may break. consequence of…
Certain vehicles are equipped with water pump pulleys which may contain a manufacturing defect, reducing the durability of the pulley.…
The vehicles were modified to extend the front frame assembly. However, certain components and attaching hardware required to extend the frame were not installed.…
Certain wind conditions can cause a down draft and create a slight positive pressure at the water heater flue gas outlet. This may cause a flame reversal to occur from the burner tube in the compartment between the water heater…
The quick release valve support bracket mounted on the axle may crack. This causes fatigue failure of the steel air lines leading to the rear parking brakes and chassis service brakes resulting in sudden loss of air pressure.…
The right hand frame rail lower flange could develop cracks due to poor grinding methods at stress points. consequence of…
The splined steering shaft may not be sufficiently engaged as designed due to inaccurate drilling of the holes in the frame to which the cab front mount member IS bolted. Under certain conditions the steering shaft may…
The wheel may develop cracks between the disc and rim. consequence of defect: if this occurs and IS not noticed, the crack could increase around the…
The lp gas lines for the refrigerator and furnace may contact the top of the rear suspension system causing damage or rupture of the propane line.…
The body IS subject to shift forward during an impact and the fuel filler hose and/or fuel vent line hose may separate from either the fuel filler neck or the gas tank. This does not comply with fmvss 301.…
The positive battery cable may contact the upper control arm or exhaust manifold shield and eventually wear through the insulation and ground the cable.…
The latch of the passenger side sliding door may become damaged if excessive force IS used to close the door. The damaged door lock mechanism will not properly engage and the door could open if vehicle IS driven over bumpy roads.…
The fuel feed and fuel return pipe assemblies includes a hose which may contact the pointed end of the radiator shroud attaching screw. this could cause a gasoline leak.…
The air system service relay supply line on the #2 axle IS incorrectly installed into the front air system reservoir. consequence of…
Incorrect tail lamp lens were installed, lens do not conform to fmvss 108, lamp reflective device and associated equipment. consequence of…
Brake air lines were incorrectly installed. The brake air lines from the bulkhead fittings to a two-way valve and to a relay valve which feeds the park brake and service brakes were inadvertently reversed during…
The routing of brake lines brought the line close to an area used to fasten the seat socket support structure to the chassis. The fastening of seat support IS done with bolts and when the bolts are tightened the free end of the…
The steering column IS connected to the steering gear by means of splined shaft couplings. These couplings are secured with a transverse bolt and lockwasher. It was found that the bolt was not tightened and torqued to specifications.…
These tires fail to meet the requirements of fmvss #109 endurance tests. A blister could develop in the tread shoulder area resulting in a partial tread separation. A sudden loss of air could occur.…
Rear supension control arm-to-spindle attachment bolts may be subject to fracture causing the rear spindle to separate during use of car.…
The cruise control causes the throttle actuator to stick preventing the disengagement of the throttle. consequence of…
A device to control the movement of the wheel chair lift IS needed to avoid sudden and unexpected movements of the lift. consequence of…
The rear hydraulic brake line on the vehicle's right side may come in contact with the supporting structure of the stepwell. The clearence between the stepwell and the brake line mounted on the framerail IS not sufficient. If…
Sanders were installed without reinforcement plates at point where mounting angle brackets are attached to the bus body floor channel. floor channel may crack, possibly allowing the sander to become detached from the bus body floor…
The compliance label installed incorrectly lists the gross vehicle weight rating. consequence of…
The fuel shut-off valve in the generator compartment may contact a battery cable terminal or the starter solenoid of the 7000 kohler generator. This contact causes an electrical short circuit and possible fuel line leakage.…
Certain of these vehicles may have been built with contaminated brake fluid. consequence of…
Jeeps may have an improperly connected fuel line fitting which could become disconnected and cause gasoline to be spilled. consequence of…