Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Insufficient grounding of the electrical pump assembly.
These vehicles were built with incorrect tire, wheel, and inflation information printed on the final stage manufacturer's certification label. This does not meet the requirements of fmvss no. 120, "tire selection and rims for motor…
These vehicles were built with an improperly plumbed brake system which affects the braking on the rear axle when running either bobtail or pulling a trailer.
The hand throttle cable can wear the brass swivel block on the governor lever through which it passes.
Approximately 10" to 11" of excess webbing can cause the first point of lock-up to be delayed. This does not conform to the requirements of fmvss no.209, "seat belt assemblies."
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
A solder bridge on the printed circuit board within the fuse panel of the power converter passed undetected through a test fixture and bypasses the fuse protecting the circuit.
Some welds were omitted from the body lock pillar, or "b" pillar. This does not comply with fmvss no.208, "occupant crash protection."
The transmission shift-cable lock clip can back out of its installed position resulting in a loss of cable adjustment. When the shift lever IS placed in the "park" position, the "park" indicator light may not illuminate.
A low air pressure warning light located in the driver's instrument cluster fails to activate if the front brake air reservoir system falls below 60 psi. This does not comply with fmvss no.121, "air brake systems."
These units are equipped with a counter weight assembly made up of 300 pounds of 1/4" plate steel welded together and bolted between the frame rails in the rear overhang just forward of the rear bumper. Some of the welds have broken due to…
The vehicles have both the supplemental inflatable restraint (sir) label and an engine start label installed on the same side of the sun visor. This does not comply with fmvss no.208, "occupant crash protection."
A wire from the low voltage output of the transformer can contact the chassis of the power converter. This condition can send large amounts of current (amperage) through the wiring of the vehicle for extended periods.
The wrong attachment bolts were used on the driver's seat. This does not comply with fmvss no.209, "seat belt assemblies."
The fuel tank strap can break allowing a slight upward movement of the tank. a dual fuel tank strap breakage can also allow the tank to slide forward or rearward.
A bracket installed to secure a high idle component onto the engine throttle arm can hook the wire harness and prevent its return to idle speed.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
The affected vehicles were built with outer tie rod ends with incorrect taper ball studs. The incorrect tapered ball studs can fracture within 50,000 miles.
This steering gear can fail from fatigue caused by high twisting forces that can occur in certain severe daily use such as turning the steering wheel up against the axle stops when the vehicle IS not on dry pavement.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
Improper installation of the rear brake line at the point at which the extended brake line first bends and extends over the left rear wheel area of the frame. If not installed with sufficient clearance, chafing of the brake line can occur…
These wheels are composed of 2 pieces - a disc and a rim which are normally welded together. These wheels lack the specified fillet welds.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
These seats may have an improperly located weld on a lever arm which supports the seat back. This weld can fail causing the seat back to fall backward freely without support to the driver.
The front safety belt buckle release buttons can break. These red plastic release buttons are marked "press." if a button breaks, pieces can fall into the buckle assembly causing the buckle to operate improperly.
These vehicles were assembled with a transmission reverse signal switch that could leak causing loss of electrical contact when the transmission IS in reverse. This does not meet the requirements of fmvss no. 108, "lamps, reflective…
These batteries may have terminals that were improperly welded.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…
These wheels are composed of 2 pieces - a disc and a rim which are normally welded together. These wheels lack the specified fillet welds.
Air system blockage in the air dryer occurs degrading the moisture removing capabilities of the dryer when the vehicle IS operated in a cold environment and moisture accumulates and freezes in the air dryer or in the line between the dryer…