Vehicle recalls
30,429 recall campaigns from NHTSA, newest first. Decode a VIN to see the ones for your car.
Vehicle recalls per year
Most recalled systems
Latest recalls
Vehicle description: transit buses equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
Vehicle description: buses equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
Vehicle description: buses equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
The rear bumper mounting brackets have been improperly installed. the mounting holes were cut oversized and can allow the mounting bolts to pull through the brackets on the chassis.
The subject vehicles have their wheelchair barriers attached to the floor structure with a bolt threaded into the floor structure. in the case of a frontal crash, at more than 20 miles per hour, with the wheelchair position occupied…
Structural failure in the chassis main beam can occur and subsequent failure of certain other rear suspension components.
An integrated circuit within the voltage regulator can contain manufacturing errors.
Vehicle description: vehicles equipped with antilock brake system (ABS). the antilock brake system (ABS) hydraulic control unit can experience excessive brake actuator piston seal wear which could cause pump-motor deterioration.
Vehicle description: motor homes built on a chevrolet chassis. the frame rail extension will not support a full liquid propane (lp) gas tank. vibration of the tank can cause the mounting hardware to become loose and eventualy could cause…
The tail light used on these vehicles was not certified for the united states.
The seat elt anchorage attachments are missing or misinstalled on these vehicles.
The "o" rings of the regulator assembly in the onan emerald and marquis brand generator sets can weaken and break when exposed to high ambient temperatures.
Vehicle description: buses equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
The u-joint bearing strap bolts were not properly tightened during assembly.
The fasteners securing the compressed natural gas (CNG) roof-mounted fuel tank lids were not properly installed and/or maintained.
The rear axle track bar bracket can separate from the frame due to missing welds or inadequate weld penetration.
Vehicles originally sold or currently registered in the following states: alaska, montana, north dakota, minnesota, wisconsin, michigan (upper peninsula), new york, maine, vermont, and new hampshire. operation at highway speeds during…
The front and/or rear hazard warning lamps (four-way flashers) do not flash when the hazard switch IS activated. this fails to comply with fmvss no. 108, "lamps, reflective devices, and associated equipment."
The steering column lower pinch bolt was not properly tightened during assembly.
Vehicle description: buses equipped with isringhausen seats in the driver position. two welds located on the back rest adjustment side of the seat frame did not meet the manufacturer's specifications.
The "o" rings of the regulator assembly in the onan emerald and marquis brand generator sets can weaken and break when exposed to high ambient temperatures.
Certain vehicles were manufactured with an incorrect rear center seat belt assembly buckle. the misbuild involved fitting a buckle for another market with the correct u.s. Specification seat belt.
Certain vehicles were manufactured with an incorrect rear center seat belt assembly buckle. the misbuild involved fitting a buckle for another market with the correct u.s. Specification seat belt.
The right front door can fail to latch fully when closing, causing the door to "bounce" back off the door seals.
These vehicles are equipped with a detroit diesel optimized idle system. if the ignition IS turned on and the fuse for the electronic control module (ecm) power feed line IS removed or burned out, unintentional cranking of the engine will…
The wheel lug nuts were not tightened to the proper specification during assembly.
The parking brake cylinder rod can separate from the socket that it IS threaded into due to defective threads.
Air bag and seat belt system warning labels are missing from the sun visor. this does not comply with fmvss no. 108, "occupant crash protection."
The propeller shaft universal joints are damaged.
Vehicle description: class 8 heavy duty vehicles equipped with eaton drive axles and axilok spindle nuts. the drive axle housings consist of a plate steel center section and two forged spindles, one of which IS welded to each end of the…