2010 BMW 128I
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2010 BMW 128I. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
7 recalls name the 2010 BMW 128I. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3…
Risk and remedy
Risk
An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
Remedy
This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain 2008-2012 BMW 128i, 135i, 135is Coupes and 128i, 135i Convertible vehicles. The wiring and electrical connectors in the blower-regulator wiring harness may overheat.
Risk and remedy
Risk
Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy
BMW will notify owners, and dealers will inspect the blower-regulator wiring harness, and replace it with a new part, free of charge. The recall began October 4, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of an earlier recall number 17V-676.
BMW of North America, LLC (BMW) is recalling certain 2008-2011 128i and 2007-2011 328i, 328xi, 328i xDrive, 525i, 525xi, 528i, 528xi, 530i, 530xi, X3 3.0si, X3 xDrive30i, X5 xDrive30i, Z4 3.0i, Z4 3.0si and Z4 sDrive30i vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Risk and remedy
Risk
An electrical short can cause the parts within the PCV valve to melt, increasing the risk of a fire, even when the vehicle is not in use.
Remedy
BMW will notify owners, and dealers will replace the PCV valve heater, free of charge. Interim letters were mailed on November 27, 2017. Owners will receive a second notification by the end of October 2018. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i…
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
BMW of North America, LLC (BMW) is recalling certain model year 2010-2011 128i Coupe, 128i Convertible, 328i Sedan, 328i xDrive Sedan, 328i Coupe, 328i Convertible, 328i Sports Wagon and Z4 sDrive 30i, 2011-2012 135i Coupe, 135i Convertible, 335i Sedan, X5 xDrive 35i, and X6 xDrive 35i, 2011 335i xDrive Sedan, 335i Coupe, 335i Convertible, 528i Sedan, 535i…
Risk and remedy
Risk
If the bolts loosen or break the engine may have reduced power or stall. An engine stall increases the risk of a crash.
Remedy
BMW will notify owners, and dealers will replace the four VANOS housing bolts for both VANOS units (intake and exhaust), free of charge. In addition, owners of approximately 170,172 model year 2010-2012 BMW vehicles equipped with inline 6 cylinder engines not covered by this recall, will receive an extended warranty to address this condition. The recall began on September 24, 2014. Owners may contact BMW at 1-800-525-7417.
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through…
Risk and remedy
Risk
If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy
BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Owner complaints
22 complaints1 involved a crash2 involved a fire
What owners report most
Latest complaints
- Electrical system · Exterior lighting › Headlights · Exterior lighting › Tail lights
The contact owns a 2010 BMW 128I. The contact stated while driving at undisclosed speeds, the headlights and taillights became inoperable. The engine warning light was illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 19V579000 (Electrical System). The vehicle…
The contact owns a 2010 BMW 128I. The contact stated while driving at undisclosed speeds, the headlights and taillights became inoperable. The engine warning light was illuminated. The contact stated that the failure was related to NHTSA Campaign Number: 19V579000 (Electrical System). The vehicle was taken to an independent mechanic who replaced the bulbs. The vehicle was taken to the local dealer, where it was diagnosed that the failure was electrical. The vehicle was not repaired. The vehicle was taken to an independent mechanic who was unable to assist. The manufacturer was not contacted. The failure mileage was approximately 125,000.
- Engine
First notified of recall in October, 2023. After 8 months, BMW tells me there is no remedy available. Eight months is more than a reasonable amount of time to remedy this defect. Please help! Thank you.
- Engine and engine cooling
The contact owns a 2010 BMW 128I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall…
The contact owns a 2010 BMW 128I. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was made aware of the issue and confirmed that parts were not yet available. The manufacturer was not made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.
- Engine
See attached document for complaint
- Engine and engine cooling
The contact owns a 2010 BMW 128I. The contact stated that while driving at a slow speed and pulling into the driveway, the vehicle stalled. While driving on two occasions, the vehicle lost motive power and stalled. The check engine and other unknown warning lights were illuminated. Additionally…
The contact owns a 2010 BMW 128I. The contact stated that while driving at a slow speed and pulling into the driveway, the vehicle stalled. While driving on two occasions, the vehicle lost motive power and stalled. The check engine and other unknown warning lights were illuminated. Additionally, door and trunk failed to open. The contact's husband checked the vehicle and noticed there was power being distributed to the battery. The vehicle was taken to the local dealer, who was unable to duplicate the failure. While the vehicle was still at the local dealer, it was diagnosed that the CAS module needed to be replaced. The vehicle was repaired, but the failure recurred. The contact stated that the failure was related to NHTSA Campaign Number 23V707000 (Engine and Engine Cooling). The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 100,000.
- Engine and engine cooling
The contact owns a 2010 BMW 128i. The contact stated that while driving at undisclosed speeds, the vehicle started running rough. The check engine warning light was illuminated. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do…
The contact owns a 2010 BMW 128i. The contact stated that while driving at undisclosed speeds, the vehicle started running rough. The check engine warning light was illuminated. The contact received notification of NHTSA Campaign Number: 23V707000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was not contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The failure mileage was approximately 52,000. VIN tool confirms parts not available.
- Engine · Fuel/propulsion system
Summary POSITIVE CRANKCASE VENTILATION (PCV) VALVE HEATER: This recall involves an engine component known as the Positive Crankcase Ventilation (PCV) valve heater. The PCV valve heater may not have been produced to specifications which could lead to a short circuit. Safety Risk Should a short…
Summary POSITIVE CRANKCASE VENTILATION (PCV) VALVE HEATER: This recall involves an engine component known as the Positive Crankcase Ventilation (PCV) valve heater. The PCV valve heater may not have been produced to specifications which could lead to a short circuit. Safety Risk Should a short circuit occur, the PCV valve heater could overheat, lead to smoldering, and possibly start melting. In extremely rare cases, this could increase the risk of a fire. Remedy An electrical wiring harness with fuse protection for the PCV valve heater will be installed for free. If the PCV valve heater is damaged, it will be replaced for free. This may take up to several hours to perform.Per the instructions on the NHTSA.GOV If the manufacturer has failed or is unable to remedy this safety recall for your vehicle in a timely manner, please contact the NHTSA Vehicle Safety Hotline at: 1-888-327-4236 or TTY: 1-800-424-9153 or file an online complaint with NHTSA. Does a Bad PCV Valve Burn Oil? If you have a bad PCV valve, you are putting your vehicle at risk. The bad valve can create a leak which will cause your car or truck to have excessive oil consumption. The oil consumption will cause the oil to burn which will cause it to smell and will leave a puddle beneath your vehicle. If you notice either of these symptoms, give us a call here at Dennis Road Automotive to schedule service. Any oil leak is a bad leak that we want to check promptly to avoid high repair costs! PCV components are typically inexpensive, and esse https://www.thedrive.com/news/44680/bmw-recalls-almost-a-million-cars-over-valve-heater-fire-risk The PCV valve is easily one of the most important parts of your car, and although it is possible to continue to operate your car with a bad valve, it is not recommended as it can corrode your car's engine over time Common signs of a faulty PCV valve include excessive oil consumption, oil leaking, a blocked breather filter, and reduction in overall performance
- Air bags
Passenger restraint system malfunction. An independent repair shop tested and found the passenger seat sensor pad is bad. From my research, BMW has a problem with this part.
- Engine and engine cooling
The contact owns a 2010 BMW 128I. The contact stated while driving 60 MPH, there were unknown warning lights illuminated. The contact was able to continue driving; however, the failure reoccurred while driving. Additionally, the contact stated that the vehicle was experiencing excessive oil…
The contact owns a 2010 BMW 128I. The contact stated while driving 60 MPH, there were unknown warning lights illuminated. The contact was able to continue driving; however, the failure reoccurred while driving. Additionally, the contact stated that the vehicle was experiencing excessive oil consumption. The vehicle was taken to an independent mechanic where it was diagnosed that the PCV valve had failed. The independent mechanic associated the failure with NHTSA Campaign Number: 22V119000 (Engine and Engine Cooling) however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the failure. The vehicle was not repaired. The failure mileage was approximately 110,000. VIN tool confirms parts not available.
- Exterior lighting
Left driver side rear taillights failed constantly I have no rear working lights . I brought in for repair and there is no fix for the lights ! I was rear ended
- Air bags · Electrical system · Engine
I have contacted BMW multiple times to come out and perform all 3 recalls. They said they would call back for details specific date to send out a certified mechanic to remedy the recalls. My wife never got a call back. I live over a hundred miles from any dealer on the VA and WV state lines. I can't afford to take time off to bring the car to them.
- Air bags
TL* the contact owns a 2010 BMW 128I. The contact stated that while operating the vehicle the air bag warning light illuminated and remained illuminated indicating that the front passenger side air bag system was deactivated although a passenger was seated in the front passenger side seat. The…
TL* the contact owns a 2010 BMW 128I. The contact stated that while operating the vehicle the air bag warning light illuminated and remained illuminated indicating that the front passenger side air bag system was deactivated although a passenger was seated in the front passenger side seat. The vehicle was taken to the local dealer (vista BMW (4401 w. Sample rd. Coconut creek, fl.) who diagnosed that the passenger side seat sensor needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 90,000.
- Air bags · Air bags › Sensor › Occupant classification
My 2010 BMW 128I has two airbag lights and one seat belt warning light that are continuously illuminated. the vehicle was taken to an independent repair facility, where it was diagnosed with a faulty "passenger side occupancy sensor" under diagnostic code 93D2. upon further research online, I…
My 2010 BMW 128I has two airbag lights and one seat belt warning light that are continuously illuminated. the vehicle was taken to an independent repair facility, where it was diagnosed with a faulty "passenger side occupancy sensor" under diagnostic code 93D2. upon further research online, I discovered that this IS a very common problem with BMW 1 series and 3 series cars the faulty sensor results in the passenger side airbag being deactivated. in fact, the problem IS so common that aftermarket companies have developed a "bypass" to=hat plugs in to the seat to reactivate the airbags without replacing the occupancy sensor. this creates another safety concern, because the bypass activates the passenger side airbag regardless of the weight of the passenger (or lack of a passenger), which could result in airbag deployment when a rear facing carseat or other underweight passenger IS in the front passenger seat. with a quote of $1,291.05 to repair the faulty passenger occupancy sensor, I feel that BMW should take ownership of this problem and prevent further injuries by recalling the sensor.
- Structure › Body · Unknown or other
Car caught fire while parked on a city street (cause unknown as deemed by the dc fire inspector). Car had been parked for approximately two days.
- Engine
TL* the contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 17v683000 (engine and engine cooling); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The…
TL* the contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 17v683000 (engine and engine cooling); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact stated that she constantly smelled a burning odor coming from the engine compartment. The dealer (BMW certified pre-owned nashville, 4040 armory oaks dr, nashville, tn 37204) was contacted and confirmed that the parts were not available for the recall remedy. The vehicle was not diagnosed or repaired. The manufacturer was notified and unable to confirm when the parts were to become available. The manufacturer advised the contact take the vehicle to a BMW dealer. The failure mileage was 115,700. Vin tool confirms parts not available.
- Air bags
TL* takata recall. The contact owns a 2010 BMW 128I. The contact was in the process of trading in the vehicle when the dealer mentioned that the vehicle was included in nhtsa campaign number: 16v071000 (air bags). The dealer stated that the part was not available, so the contact was unable to…
TL* takata recall. The contact owns a 2010 BMW 128I. The contact was in the process of trading in the vehicle when the dealer mentioned that the vehicle was included in nhtsa campaign number: 16v071000 (air bags). The dealer stated that the part was not available, so the contact was unable to schedule the recall repair within a reasonable time frame. Global imports BMW (500 interstate n pkwy, atlanta, ga 30339, (800) 294-1853) and united BMW (1501 alpharetta hwy, alpharetta, ga 30009, (678) 430-3775) were been unable to verify when the part would be available. The manufacturer was contacted. The contact was not experiencing a failure. The vin was not available. Parts distribution disconnect.
- Air bags
TL* takata recall. The contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Shelly…
TL* takata recall. The contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. Shelly BMW (6750 auto center dr, buena park, ca) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
- Air bags
TL* takata recall. The contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags). The parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact…
TL* takata recall. The contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags). The parts to do the repairs were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The contact called BMW of louisville (4 swope autocenter dr, louisville, ky 40299 (502) 287-1501) and was informed that the parts were not available for the recall remedy. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Parts distribution disconnect.
- Air bags
TL* the contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (BMW of…
TL* the contact owns a 2010 BMW 128I. The contact received notification of nhtsa campaign number: 16v071000 (air bags); however, the parts to do the repair were unavailable. The contact stated that the manufacturer exceeded a reasonable amount of time for the recall repair. The dealer (BMW of fairfax located at 8427 lee hwy, fairfax, va 22031; (800) 641-4873) was contacted and confirmed that the parts were not available for the recall remedy. The manufacturer was not contacted. The manufacturer was not made aware of the issue. The contact had not experienced a failure. Vin tool confirms parts not available.
- Air bags · Electronic stability control (esc)
I called BMW beverly hills several times since I owning the car. I have taken it in because I received a recall letter and it seemed to have an electrical shortage. I told them I did not feel safe driving the car with a potential electrical issue and air bag defect. I dropped off my car 2 times.…
I called BMW beverly hills several times since I owning the car. I have taken it in because I received a recall letter and it seemed to have an electrical shortage. I told them I did not feel safe driving the car with a potential electrical issue and air bag defect. I dropped off my car 2 times. Never got an update. No one went over what was done to to the car. They wanted me to buy an extended warranty. After expressing several times and dropping off my car 2-3 times, they never called me back or responded... I had a car accident in late november or early december. Thank god my airbag did not deploy but I feel completely unsafe driving my car because I do not believe the electrical issue I complained about and the airbag I am waiting to be replaced. electrical: when it IS stationary it IS having electrical issues. Turning it on IS an issue. airbag: I called several times to request my airbag be replaced because I did drive the car in palm springs where it IS very hot. I also recently had a car accident in this car. I feel completely unsafe in my car. *tr - (recall related issue) ts
- Engine and engine cooling
TL* the contact owns a 2010 BMW 128I. While driving approximately 45 mph, the vehicle decelerated and the check engine indicator illuminated briefly and returned to normal. The failure occurred on numerous occasions. The dealer stated that the oil needed to be serviced. The failure recurred, but…
TL* the contact owns a 2010 BMW 128I. While driving approximately 45 mph, the vehicle decelerated and the check engine indicator illuminated briefly and returned to normal. The failure occurred on numerous occasions. The dealer stated that the oil needed to be serviced. The failure recurred, but the check engine indicator did not illuminate. The vehicle was included in nhtsa campaign number: 14v176000 (power train). The manufacturer was not notified of the failure. The failure mileage was unavailable.
- Structure · Visibility/wiper
TL* the contact owns a 2010 BMW 128I. The contact stated that as she was entering the vehicle, she noticed film covering the windshield. The vehicle was taken to the dealer four times. The dealer confirmed that the failure was due to the car interior releasing air. The manufacturer was contacted.…
TL* the contact owns a 2010 BMW 128I. The contact stated that as she was entering the vehicle, she noticed film covering the windshield. The vehicle was taken to the dealer four times. The dealer confirmed that the failure was due to the car interior releasing air. The manufacturer was contacted. The vehicle was not repaired. The failure mileage was 4,000 and the current mileage was 25,000. updated 07/06/12*lj the consumer also stated the film was very thick and hard to wipe off. The dealer informed the consumer, the problem was with the air condition, and the coil. The consumer stated each time she picked the vehicle up, she thought the problem was fixed, only for it to return again. BMW informed the consumer there was nothing they could do, as the problem was a bi-product of the interior breathing.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10181214Power Reduction, FC2A82 Intake VANOS and/or FC2A87 Exhaust VANOS Camshaft Fault: The ?Service Engine Soon? (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If theignition is cycled, the engine then usually performs normally.
- 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
- 10162434Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
- 10162431"Erroneous CC Message "Remote control! Do not switch off the engine" is Displayed. An erroneous CC message, "Remote control!" " Do not switch off the engine" is displayed in the Central Information Display (CID). The engine can still be started, even with the CC message displayed. CAUSE: Car Access System (CAS) software error"
- 10162427Convertible Top Does Not Open Properly. When opening the convertible top, the interior cover flap remains open. CAUSE: The cable for the flap operation is either kinked or dislodged.
- 10162416"Power Reduction, FC 2A82 Intake VANOS and/or FC 2A87 Exhaust VANOS Camshaft Faults are Stored in DME. The ""Service Engine Soon"" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled, the engine then usually performs normally. The following faults are stored in the DME: * 2A82 VANOS intake - stiff; jammed mechanically * 2A87 VANOS exhaust - stiff; jammed mechanically * 130108 VANOS intake: control fault, position not reached * 130308 VANOS exhaust: control fault, position not reached For the N54 engine, the following secondary faults may also be stored: * 120408 Charge-air pressure control, cut-out: Boost pressure accumulation blocked * 3100 Boost-pressure control, deactivation - boost-pressure buildup prohibited CAUSE The VANOS faults can be caused by an insufficient oil pressure supply to the inlet VANOS adjustment unit. To effectively move the camshafts to the target positions in the specified time and under all engine conditions, sufficient oil pressure supply to the VANOS control pistons must always be available. If engine operation requires the VANOS system to quickly advance or retard the intake or exhaust camshaft, faults may be stored if the camshaft is ""late"", or does not reach the target position. In this situation, engine power may be reduced and a check control message is displayed. The consequential fault 3100 or 120408 can also be set in the DME fault memory as well."
- 10162405Wear Marks on the C-pillar Area of the Soft Top Canvas. Wear marks may form on the soft top cover in the C-pillar area, above or below the canvas seam and or along the seam. These wear marks may be visible on one or both sides and are generally less than 4mm in diameter. They are first visible as a smooth spot on the cover, and progress to a white mark. In severe cases, a hole could form in the cover material. 1. Improper limit spacing between the soft top cover and the soft top frame when folded in the fully open position 2. The seal carrier contacting and wearing the canvas top cover and threads 3. Tension straps and main bump stops out of adjustment.
- 10162404"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Follow the diagnosis test plan using the latest ISTA version. In Information Search, select the "Function Structure"" tab. Select Body, Mirror, Door mirror, Driver's or passenger side, Exterior Mirror Malfunction, and then press "Start Search". Select test plan ""AM5102_00010".
- 10162395N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine has a loss of power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
- 10160287TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10160244TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10154816In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
- 10153726Takata class action settlement. Customer support program. Front driver side airbag modules.
- 10152314Door Open Message Displayed, Even Though Door Is Closed. The customer complains that while driving, a CCM (check control message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. Unspecified FRM door lock status due to voltage variations
- 10151335Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware.
- 10151300N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints This Service Information bulletin and attachment supersedes SI B11 06 16 dated April 2016.. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151247N51, N52, N52K and N52T Engines: Various Eccentric Shaft Sensor Faults stored in the DME - Diagnostic Hints. The customer may complain about one of the following: Rough engine running Engine cannot be started (crank no start) Check Engine Light illuminated One or more of the following faults may be stored in the DME: 2A37 - Valvetronic, eccentric shaft sensor plausibility 2A47 - Valvetronic, eccentric shaft, signal plausibility 134E08 - Eccentric shaft plausibility (on F10, F25 vehicles only) CAUSE The VVT eccentric shaft sensor connector, and/or DME connector may have oil contamination due to oil leakage at the VVT sensor gasket.
- 10151170N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
- 10151119SI B84 03 14 February 2016 Communication Systems Technical Service This Service Information bulletin supersedes SI B84 03 14 dated October 2014. SUBJECT Bluetooth Connection Failures. There are various connectivity failures with the following devices: Apple iPhones Samsung S6 and the S6 Edge. Connectivity failure examples are: Call disconnection - Call is transferred back to the handset. In some instances the call is then transferred back to the vehicle. Contact List incomplete General connection failures CAUSE Apple iOS software (issue started with iOS 8.3 continues with iOS 9.x and its variants) Samsung S6 and S6 Edge device firmware CORRECTOPM None available at this time. We are currently working with the device manufacturer on a solution.
- 10151115SUBJECT Audio System Speaker Testing. For audio system speaker testing there is a NED (Non Electrical Diagnosis) Test Plan available. CAUSE We previously recommended use of the Audio Test CD (ATC) from BMW. This CD has been discontinued.
- 10151079SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual identification in ETK may result in an incorrect part number.
- 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10151023Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
- 10150389Service Action: CIC - Install Navigation Road Map Database 2013. The Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD).
- 10150385"CCC - ""Please Insert Navigation DVD"" Appears on CID. The navigation map DVD cannot be read or detected. The message ""Please insert navigation DVD"" appears in the CID (Central Information Display). The navigation system is inoperative. This situation may also occur when upgrading to a new navigation map. The old map is recognized but the new one is not. CAUSE Faulty DVD drive; read error due to hardening of the anti-vibration gel on the read head"
- 10150365"N51, N52K and N52T: Idle Fluctuation During Engine Warm-up Phase. After a cold engine start, the idle speed may be unstable or start fluctuating up and down slightly while the vehicle is stopped. On vehicles with automatic transmissions, roughness or shuddering may be felt during this warm-up period when diving away slowly in ""D"" or in ""R"" without depressing the accelerator pedal. No relevant errors are stored in the DME fault code memory, and these symptoms are no longer present once the engine is at operating temperature (> 90C). Unfavorable DME software"
- 10150334"Service Action: CIC - Install Navigation Road Map Database 2013. Before delivering affected vehicles to the customer, the Car Information Computer (CIC) road map database 2013 must be installed onto the CIC internal Hard Disc Drive (HDD). Note: The INITIAL enabling code ""FSC CIC map, N. America 2013 INITIAL"" is necessary to start the installation process and to activate the road map database."
- 10150330"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
- 10150265Intermittently Stored FM Radio Stations Default to FM 87.7. Intermittently, the stored FM radio stations default to FM 87.7 after vehicle start-up. CAUSE 1. Low battery voltage or voltage drop at the head unit 2. Radio station preset contains FM 87.7 3. Remote key memory not set correctly or the setting is lost
- 10150264"The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" 1. When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it. 2. The new part has incorrect coding."
- 10150224"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Electrochromic Mirror,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150218N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine exhibits a loss of power; and the Service Engine Soon lamp is illuminated. One, or more of the following faults may be stored. E70, E71, E82, E88, E90, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One, or both (intake and/or exhaust) of the VANOS gear assemblies have failed; the attaching bolts may have also loosened and/or broken.
- 10150173"Outside Door Mirror Moves when Locking or Unlocking the Vehicle. The door mirror tilts immediately after unlocking or locking. The mirror position does not correspond to the memory position preset by the customer. Pressing the seat memory button typically will return the mirror to the stored position. Poor electrical contacts of the mirror drive in the mirror housing INFORMATION The problem has been integrated into ISTA diagnostics. Complete the diagnosis test plan using the latest ISTA version. The test plan can be accessed via the following path: ""Information Search / Function Structure / Body / Mirror / Exterior mirrors / Driver's or passenger side / Exterior Mirror https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/15...12/6/2013 Page 2 of 2 Malfunction,"" and then press ""Start Search."" Select the test plan ""AM5102_00010."""
- 10150167Incorrect Remaining Service Life from CBS Data for Brake pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Note: E9x vehicles with xDrive are not affected by this bulletin. Software calculation in the brake pad wear model
- 10150133In all audio modes (radio, CD, AUX-In, etc.), the audio output is distorted. It is more noticeable with high bass and high audio volume settings. There may also be an intermittent interference noise coming from the loudspeakers at low audio volume or when the radio is turned off. Audio settings in the RAD2+ (radio professional)
- 10150131"Enabling and Replacing New OC3 Seat Mat. The replacement OC3 seat mat (front passenger seat occupancy) will not enable when following ISTA Repair Instruction REP 65 77 604, ""Replacing sensor mat (OC3 mat) for passenger seat occupancy detector."" When the new mat is installed in the vehicle, too much pre-load pressure will prevent the mat from being enabled. ISTA/P WILL NOT enable the new part, and will cause permanent damage to it."
- 10150130The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
Every BMW 128I model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.