2002 BMW 325XIT
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › BMW › 325XIT › 2002
These records cover every 2002 BMW 325XIT. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2002 BMW 325XIT. Newest first.
BMW of North America, LLC (BMW) is recalling certain 2000-2005 323iT, 325iT, 325xiT, 320i, 323i, 325i, 325xi, 328i, 330i and 330xi and 2000-2006 323Ci, 325Ci, 328Ci, 330Ci, M3 Coupe, 323Cic, 325Cic, 330Cic, and M3 Convertible vehicles equipped with non-desiccated frontal Takata PSAN inflators and PSPI passenger frontal air bag inflators containing phase…
Risk and remedy
Risk
An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy
BMW will notify owners, and dealers will replace the passenger's front air bag, free of charge. The recall began February 13, 2020. Owners may contact BMW customer service at 1-800-525-7417.
BMW is recalling certain model year 2002-2003 325i, 325xi, 330i, 330xi sedans; 325Ci and 330Ci coupes and convertibles; 325iT and 325xiT Sports Wagons; and M3 coupes and convertibles to address a safety defect in the passenger side frontal air bag which may produce excessive internal pressure causing the inflator to rupture upon deployment of the air bag.
Risk and remedy
Risk
In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking and potentially seriously injuring the passenger seat occupant or other occupants.
Remedy
Owners are advised not to drive their vehicles until they have been repaired. BMW intends to issue initial notifications to owners informing them of the safety defect in June 2013. Once replacement parts are available, estimated for July, BMW will notify owners again to contact their dealers and schedule a replacement of the passenger air bag, free of charge. Owners may contact BMW customer service at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Owner complaints
1 complaints
Latest complaints
- Fuel/propulsion system
When starting the car after it has been in cold temperatures (-25 c or colder) the fuel injectors leak significantly. it appears as if the body of the injectors shrinks such that the injector pulls away from the fuel rail. a steady stream of fuel IS observed out of several injectors. the amount…
When starting the car after it has been in cold temperatures (-25 c or colder) the fuel injectors leak significantly. it appears as if the body of the injectors shrinks such that the injector pulls away from the fuel rail. a steady stream of fuel IS observed out of several injectors. the amount of fuel leaking IS enough to observe a steady stream of fuel exiting underneath the engine compartment. this continues until enough heat has built in the engine compartment to warm the injectors and cause them to seal against the fuel rail. while driving in temperatures around 25 c, this usually takes 10 to 15 minutes to warm up enough to stop the leaking.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249437The basic conditions for initializing the power windows are not met.
- 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
- 10184591SERVICE ACTION - HEAD AIR BAG HOLDER RETROFIT: A rattle noise may develop from the head air bag (ITS) gas generator contacting adjacent component. This noise can be heard while driving on an uneven roadway.
- 10160287TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10160244TAKATA AIR BAG RECALL-RELATED SHORT-TERM ALTERNATE TRANSPORTATION AND CONSEQUENTIAL REPAIRS This Service Information bulletin supersedes SI B01 31 18 dated October 2018.
- 10154816In an effort to improve the completion rate on Takata air bag recall affected vehicles; BMW NA has expanded the BMW Ultimate Rewards platform to include a new Recall Support page. This page will allow IRFs to check their customers VINs for open Takata recalls; and get rewarded for helping us with completing repairs.
- 10153726Takata class action settlement. Customer support program. Front driver side airbag modules.
- 10150160State Inspection and Emission (I/M) Test Fails Due To an Invalid VIN Number. The customer of an affected vehicle may fail to pass an I/M test due to a non-compliant 17digit vehicle identification number (VIN) stored in the DME (Digital Motor Electronic). The VIN read out and displayed on the state test printout does not match the actual VIN of the vehicle. If the DME was reprogrammed using the previously available BMW service equipment (e.g., Progman, GT1), it is possible that only the last 7 digits of the VIN were entered into the DME, and positions 4 through10 may only contain default characters. For example: The state I/M tester or OBD scan tool may read out WBAAA00000A123456 instead of the correct full 17-digit VIN, WBAZZ03492A123456.
- 10149558For the above-referenced vehicles with passenger?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata passenger?s side airbag module in a listed vehicle.
- 10149557For the above-referenced vehicles with driver?s side airbag modules, BMW of North America, LLC (?BMW NA?) will provide a Customer Support Program as outlined in the Takata Settlement Customer Support Program Overview attachment. This ?component-specific? customer support program applies only if there is a defect in materials or workmanship of the Takata driver?s side airbag module in a listed vehicle.
- 10148179Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
- 10148100Special Technical Campaign. The National Highway Traffic Safety Administration (NHTSA) has urged vehicle manufacturers to conduct an investigation into air bags which may not deploy correctly. BMW is cooperating with this request. Takata is a supplier of air bags to several automotive manufacturers. They have informed NHTSA of a small number of cases of improperly deploying air bags in a few specific areas of the US. None of the reported cases involve any BMW vehicles. No determination has been made by BMW and Takata that a safety issue exists.This program involves the driver and front passenger air bag system. Specifically, the air bag system may have been manufactured with an inflator that was not produced to specification. After long-term exposure in high absolute humidity environments, in a crash in which air bag system deployment occurs, the air bag system housing may rupture. To assist Takata with their determination, BMW will be collecting air bags from a limited number of customer vehicles. Once the affected vehicle population has been determined, owners of affected vehicles will be notified by letter to visit their authorized BMW center to have their air bag(s) replaced. Additional information will be provided at that time. A press release from NHTSA on this topic is expected to be issued on Monday, June 23, 2014.
- 10147242Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance.
Every BMW 325XIT model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.