2014 BMW 740I

Recalls

1 recall names the 2014 BMW 740I. Newest first.

• Exterior lighting

  Jun 14, 2017NHTSA 17V37900092 vehicles

  BMW of North America, LLC (BMW) is recalling certain 2013-2015 740i, 740Li, 740Lxi, 750i, 750xi, 750Li and 750Lxi and 2014 ActiveHybrid 7 vehicles. The affected vehicles may have received incorrect replacement left rear taillight assemblies. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS)…

  Risk and remedy

  Risk

  Vehicles with the incorrect left rear lamp assemblies may be less conspicuous to other drivers, possibly increasing the risk of a crash.

  Remedy

  BMW will notify owners, and dealers will inspect the vehicles and replace any incorrect left rear taillight assemblies, free of charge. The recall began August 11, 2017. Owners may contact BMW customer service at 1-800-525-7417.

  Full recall details →

Owner complaints

Latest complaints

• Sep 6, 2022CACrash1 injury
  Unknown or other
  The car had been running properly for months/years without any complaints. Last week while driving on a surface street, after a turn, the car that was going at about 40 MPH, suddenly started accelerating by itself to may be 70 or 80 MPH, this confused and shocked the driver and to avoid hitting the…

  The car had been running properly for months/years without any complaints. Last week while driving on a surface street, after a turn, the car that was going at about 40 MPH, suddenly started accelerating by itself to may be 70 or 80 MPH, this confused and shocked the driver and to avoid hitting the cars in front, the driver crashed the car into a tree. The car was totaled, fortunately the driver did not have any serious injuries. Talked to a private mechanic if there is a way to find out what happened. He said that based on the amount of damage and the fact that the car most probably cannot be started, he would not really be able to find what happened. Are there other BMW's that have had such issues.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10249437The basic conditions for initializing the power windows are not met.
• 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
• 10247567Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
• 10245422Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
• 10245379The carpet welcome light(s) turns on either after a delay, or does not function at all.
• 10230716With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered into a nationwide settlement with the plaintiffs in the following class action: Isley, et al. v. Bayerische Motoren Werke Aktiengesellschaft and BMW of North America, LLC.
• 10227568According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
• 10225126Vehicle cannot be opened or closed using comfort access, engine start is not possible, and the vehicle may not start when placing the key against the steering column.
• 10214990The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609 (as of 7/2012 production). This uses map North America NEXT. The Headunit High 2 (HU-H2), also called NBT-EVO, superseded the NBT HU and was introduced in 3/2014. This uses map North America EVO. The Headunit High 4 (HU-H4, also called MGU21) superseded the MGU starting with certain MY2021 vehicles with option code 6U3 Live Cockpit Professional. This uses map North America JOY. The ENTRY Media/Navigation (HU-B) is the low line business version of the navigation system and was introduced in 3/2014. This uses map North America ROUTE. The ENTRY NAV EVO (HU-B2) replaced Entry Media/Navigation as the low-line business version and was introduced in certain MY2018 vehicles. This uses map North America WAY.
• 10211851This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10200487TELEMATICS UNIT DEACTIVATION DUE TO 3G CELLULAR TECHNOLOGY DISCONTINUATION: The discontinuation of 3G cellular communication for Combox, TCB 3G and ATM 3G (Telematics ControlModule) can no longer be supported by the cellular network provider starting February 2022.
• 10199287CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10198894CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10188954COLLECTION OF DRIVER'S AND PASSENGER'S SIDE AIR BAGS: BMW intends to perform evaluations and analyses on these side air bags.
• 10186215INCORRECT TORQUE SPECIFICATION FOR THE HIGH-PRESSURE PUMP IN ISTA: The current version of ISTA states the incorrect tightening torque for the High-Pressure pump M6 mounting bolts to the cylinder head cover. The correct tightening torque is only 12 Nm for the M6 bolts.
• 10184589COLLECTION OF DRIVER'S AND PASSENGER'S SIDE AIR BAGS: BMW intends to collect approximately 300 sets of driver's and passenger's side air bags for evaluation. The selected vehicles for air bag replacement must have been predominantly driven/operated in high temperature & high humidity southern areas of the United States and its territories.
• 10179812CRACKING NOISES FROM THE FRONTAXLE AREA WHILE TURNING THE WHEELS, WHEN STATION: Cracking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.
• 10179009NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
• 10175267Power Reduction FC2A82 Intake VANOS and/or FC2 A87 Exhaust VANOS Camshaft Fault: The "Service Engine Soon" (MIL) lamp is illuminated and engine power reduction is perceived. This situation can occur after driving for some time with the engine at full operating temperature. If the ignition is cycled the engine then usually performs normally.
• 10174320CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both in identifying the issue and providing technical support. CAUSE Not enough information is available for BMW NA engineers to assist the technician in diagnosing the root cause.
• 10174032AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
• 10174015TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
• 10172479LIMITED WARRANTY EXTENSIONTO 10 YEARS/120000 MILES: This Service Information Bulletin replaces SI B01 05 18 dated July 2019. Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.
• 10165266SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
• 10163995DIAGNOSTIC HINT: CATALYTIC CONVERTER INSPECTION AFTER LOSS OF CRANKSHAFT SIGNAL. In certain situations when the crankshaft position signal is lost while driving the malfunction indicator lamp (MIL) and an engine malfunction check control message (CCM #29) may be displayed. The engine may run roughly or with reduced power.
• 10163994The crankcase ventilation hoses may become brittle and break when they come in contact with hot engine components. One or more of the crankcase ventilation hoses are not FPM (fluoroelastomer) rubber material. The FPM rubber material is engine heat resistant. Or The plastic corrugated hoses are not fitted with the self-locking spacers. The self-locking spacers maintain an air gap between the hoses and the hot engine components.
• 10163029N55 ENGINE: FC 28A0 OR 101F01 THROTTLE VALVE OPENING ANGLE. The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.
• 10163026N63 ENGINE: OIL CONSUMPTION CLASS ACTION SETTLEMENT DIAGNOSIS AND REPAIR PROCEDURES. While engine oil consumption may create a customer inconvenience in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle.
• 10161555Service Information May 2019 Engine Electrical Systems B12 19 19 Technical Service. On the affected vehicles a DME software error prevents the Check Control Message (CCM) "Low Engine Oil Level" to be displayed in instrument cluster (Kombi) when the engine oil level drops below the minimum level.
• 10160329N63T - CCM "LOW OIL LEVEL" NOT DISPLAYED. Drivetrain Malfunction Warning is illuminated and DME fault code 1C4002 (Engine oil level: too low) is stored. Customer complains that Check Control Message (Low Oil level") has never been displayed. The engine oil level measurement test works correctly and shows low oil level when checked under Vehicle Status tab in CID. Instrument cluster software error.
• 10160286On the affected vehicles the CBS engine oil service interval has been reduced to 1 year/10000 miles to make these vehicles consistent with all other N63x engine equipped vehicles.
• 10160246N63T - CCM "LOW OIL LEVEL" NOT DISPLAYED. Drivetrain Malfunction Warning is illuminated and DME fault code 1C4002 (Engine oil level: too low) is stored. Customer complains that Check Control Message (Low Oil level") has never been displayed. The engine oil level measurement test works correctly and shows low oil level when checked under Vehicle Status tab in CID. Instrument cluster software error.
• 10160243On the affected vehicles the CBS engine oil service interval has been reduced to 1 year/10000 miles to make these vehicles consistent with all other N63x engine equipped vehicles.
• 10152356"""Message"" Option Is Missing After Programming. Messages can be sent to the vehicle and are received as indicated by the envelope icon displayed in the CID. However, the menu option ""Message,"" used to retrieve or access messages, is no longer available in the iDrive menu. CAUSE Software error with ISTA/P 2.49.2 to 2.49.4 I-Level F001-13-03-503 to F001-13-03-505"
• 10152347N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME. Correct part numbers and applicable production dates: P/N 13 64 7 639 994 is for all vehicles produced from 7/2013 P/N 13 64 7 597 870 is for all vehicles produced up to 7/2013
• 10152317Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
• 10151411"The ""Variable Damper Control"" (VDC) valves for the spring strut shock absorber on the left front axle may fail, causing the Check Control message: ""Chassis function restricted. It is possible to continue driving. Have the system checked as soon as possible by your local BMW Service Workshop"" to be displayed."
• 10151404Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle deviation outside tolerance? 44011B - Set torque outside of the torque characteristic curve EGS ? 420611 - DSC interface (wheel speed): non-permitted deviation of wheel speed (actual speed of wheel RL/FL/RR/FR, 0x254) from output speed and turbine speed DSC ? 48097D - Transfer box: Fault, clutch position known, only rear-wheel drive These symptoms or faults would be stored on a vehicle with low mileage (< 12,500 miles). CAUSE A front or rear differential with the incorrect gear ratio was installed in the car. The front and rear differentials need to be geared exactly the same for the xDrive to function properly.
• 10151375HeadUp Display does not Show Full Street Names. INFORMATION Design of the HUD has limited display area. (It can only show a certain number of text characters). NOTE: Parts replacement or programming the vehicle will not recitify the situation!
• 10151373"BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: Effective for repairs dated on or after January 1, 2015. Applicable to vehicles that are still covered by the BMW Maintenance Program. This program is valid for 4 years or 50,000 miles, whichever occurs first. The calculation is based on the current date of repair. It is ""applicable"" when the 12volt battery was not replaced within the last 12 months. You can then perform the battery replacement as outlined below. Please check the warranty claim history for the specific vehicle in the DCSnet Warranty Vehicle Inquiry to confirm the battery was not already replaced within the previous 12 months."

Every BMW 740I model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.