2004 BMW 760LI
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
These records cover every 2004 BMW 760LI. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Owner complaints
3 complaints
What owners report most
Latest complaints
- Fuel/propulsion system
TL* the contact owns a 2004 BMW 760li. The contact stated that the vehicle idled abnormally high and would drive roughly. The contact took the vehicle to the dealer where the fuel injectors were replaced. The dealer replaced all twelve fuel injectors on the vehicle. The vin was not available. The failure and the current mileage was 159,000. *tr
- Power train
TL* the contact owns a 2004 BMW 760li. The contact stated that while driving approximately 25 mph, the vehicle stalled without warning. The vehicle was taken to the dealer for diagnostic testing. The technician stated that the ecm unit would have to be replaced. The contact referenced nhtsa…
TL* the contact owns a 2004 BMW 760li. The contact stated that while driving approximately 25 mph, the vehicle stalled without warning. The vehicle was taken to the dealer for diagnostic testing. The technician stated that the ecm unit would have to be replaced. The contact referenced nhtsa campaign number: 04v344000 (power train) but was advised by the manufacturer that the vin was not included in the recall. The vehicle was not repaired. The approximate failure mileage was 74,000.
- Fuel system, gasoline
Hard to start, cranks for a while till it builds up pressure then starts. Idles rough and sometimes dies when sitting at stop light, and sputtering power at time when taking off, also when it stalls while driving it IS a total loss of power for steering and other controls, very dangerous when it…
Hard to start, cranks for a while till it builds up pressure then starts. Idles rough and sometimes dies when sitting at stop light, and sputtering power at time when taking off, also when it stalls while driving it IS a total loss of power for steering and other controls, very dangerous when it happens. BMW states it IS the high pressure fuel pump and the part IS $2,700 + 1300 labor. this IS the flagship car for BMW. Please recall and replace both pumps before someone gets killed. why should one have to pay a high amount of money for a car that has a known defect and IS not being addressed. *tr
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Vehicle Rollaway
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the…
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 10249437The basic conditions for initializing the power windows are not met.
- 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
- 10247567Engine will crank but not start. There is no communication with the integrated fuel module (TFE) whendiagnosing with ISTA. The following two fault codes will be stored in the DME: 032B43 - Low fuel pressure system, electric fuel pump: pressure value too low CDA594 - Message (- 0x33E) missing, receiver DME, transmitter TFE
- 10245422Customers may state that the alarm system (DWA) is not active after locking their unoccupied vehicle. Depending on the vehicles equipment and settings, no acoustic or optical confirmation (folding the mirrors/blinking confirmation) is noticeable. Additionally, the red anti-theft alarm LED in the interior mirror does not briefly flash every 2 seconds, indicating the alarm is armed.
- 10218398Component-Specific Limited Warranty Extension For the eligible vehicles, BMW of North America, LLC (BMW NA) is extending the limited warranty for the vehicle's front and rear air suspension strut assemblies (item # 1 Front and # 2 Rear, shown) to: 8 years/80,000 miles, as determined by the vehicle's original in-service date. Other air suspension system-related components/issues are excluded from this coverage. This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
- 10182619Discharged Battery Energy Diagnosis Must Be Performed: The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle "discharged battery" complaints. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair.
- 10152354Check Control Message Displayed; Turn Signals Flash Fast.
- 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10150330"Discharged Battery: Energy Diagnosis Must Be Performed. The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle ""discharged battery"" complaints. A discharged battery can have various causes, most of which do not concern the battery itself. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to www.batteryuniversity.com/parttwo-42B.htm For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. In order to properly repair the vehicle the first time in the workshop, it is very important that the diagnostic test plans are performed to completion with all results taken into to consideration. The procedure as outlined below contains information that will guide the technician into properly repairing the vehicle and getting paid for a warranty claim. CAUSE Refer to the ""Procedure"" section of this Service Information for details."
- 10149279Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10148273Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shutting
- 10148120Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored: * 213901 - Power management: Reduction or shutdown of individual electrical consumer * 8040BD - Reset or deactivation of Terminal 30F * 8040B9 - De-activation of terminal 30B: Top start capability limit reached * 8020E8 - Reset or deactivation of terminal 30F * 800E89 - FRM: start capability limit reached with lights active during stationary mode * 93076B - Deactivation of terminal 30B: upper start capability limit reached * 93076A - Deactivation of terminal 15: upper start capability limit reached, but deactivation preventer active * 93076C - Deactivation of terminal 30B: upper start capability limit reached, but deactivation preventer or legal loads active * 930769 - Deactivation of terminal 15: upper start capability limit reached Note: When the outside temperatures drop below 46F, the charging system is switch to full charge. CAUSE * The check control message (ID 229) is caused by a heavily discharged battery. * The check control message is triggered when the current state of charge (SoC) of the battery approaches the minimum SoC that is required to start the vehicle (start capability limit). * In low outside ambient temperatures, the start capability limit of the vehicle is higher. Therefore it takes more energy from the battery to start a cold engine. * Without the early warning of the check control message, the current state of charge would drop below the start capability limit and the vehicle would not start. * The vehicle's intelligent power management system actively takes measures to increase the charge of the battery, such as increasing idle speed and reducing or shut
- 10147945Delay in Automatic Driving Light Switching On/Off. When driving out of a tunnel or exiting underground parking, the automatic driving light remains switched on for two minutes, even in daylight. The automatic driving light switching on/off can be shorter or longer when it starts to get dark. CAUSE The software for the switch-on threshold is lowered to protect the xenon light source.
- 10147758This Service Information bulletin supersedes SI B07 03 14 dated May 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10147598"SUBJECT N62TU: ISTA Service Function for DME ""RAM Backup"". The ISTA Service Function test plan should be performed to clear stored values in the DME RAM memory after repairs are completed, in the following situations: z VANOS or engine-related repairs if any of the following faults cannot be cleared: 2A90 - Exhaust camshaft, tooth offset to crankshaft 2A91 - Exhaust camshaft 2, tooth offset to crankshaft 2A8A - Inlet VANOS, adaptation stop 2A8B - Inlet VANOS, adaptation stop 2 2A8C - Exhaust VANOS, adaptation stop 2A8D - Exhaust VANOS, adaptation stop 2 2A8E - Inlet camshaft, tooth offset to crankshaft 2A8F - Inlet camshaft 2, tooth offset to crankshaft z The engine oil level display continues to show as overfilled even after being corrected. This is also described in SI B12 05 07."
- 10147123Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10147067This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10146779Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits This Service Information bulletin supersedes SI B07 03 14 dated October 2015.. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
- 10145306NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
- 10143564NAVIGATION SYSTEM: REPORTING MISSING OR INCORRECT ROAD MAP DATA: The route guidance is inaccurate and therefore irritating to the customer; or it is not possible to locate certain addresses, for instance:
Every BMW 760LI model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.