2015 BMW R1200 S Adventure

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10249027The electrical system of BMW vehicles has been subject to an ongoing development process over the last few years. This has led to increased demands being placed on the battery. This document covers important information for the dealer on how to handle discharged battery complaints.
• 10227580The options in the Reversing Assist Camera menu are greyed out and cannot be adjusted.
• 10227568According to the customer, the airbag warning light was on, but it may not be illuminated when the vehicle arrives in the workshop. 1. ACSM fault code "930A60 - Seat occupancy detection, front passenger; malfunction" is stored. The fault may or may not currently be present. Or 2. ACSM fault code "930A1C - Front passenger seat occupancy detection transmitting fault(moisture)" is stored. The fault may or may not currently be present.
• 10211851This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, "N63 Customer Care Package." The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10199287CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10198894CLASS ACTION SETTLEMENT: N54/N54T/N55 ELECTRIC ENGINE COOLANT PUMP . With the court's FINAL approval, BMW of North America, LLC (BMW NA) has entered a nationwide settlement with the plaintiffs in the following class action: Oliver, et al v. BMW NA, et al
• 10194296Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
• 10188954COLLECTION OF DRIVER'S AND PASSENGER'S SIDE AIR BAGS: BMW intends to perform evaluations and analyses on these side air bags.
• 10184575TICKING NOISE FROM THE FRONT AXLE WHEN CORNERING: The customer may complain of a metallic ticking noise from the front axle, when cornering, maneuvering, parking or pulling away from a parking space.
• 10179812CRACKING NOISES FROM THE FRONTAXLE AREA WHILE TURNING THE WHEELS, WHEN STATION: Cracking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or when turning the steering wheel while stationary.
• 10179009NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data must be reported directly to the map supplier.
• 10174032AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1 the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without pre-ordering the enabling code. This enabling code will be automatically delivered through ISTA and it then activates the navigation system.
• 10174015TAILGATE UNINTENTIONALLY OPENS: This Service Information Bulletin (Revision 4) replaces SI B51 30 16 dated March 2018. Trunk/tailgate may open when vehicle is locked Trunk/tailgate may open while the vehicle is in motion usually after stopping such as a traffic light etc. Vehicle key trunk/tailgate button may be accidentally pressed thus opening the tailgate.
• 10174009TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs.
• 10172479LIMITED WARRANTY EXTENSIONTO 10 YEARS/120000 MILES: This Service Information Bulletin replaces SI B01 05 18 dated July 2019. Engine starts poorly (hard starting) rough idle and misfires. The Service Engine Soon (MIL) lamp is on.
• 10169460HELPFUL INFORMATION FOR CUSTOMER DISCUSSIONS REGARDING MOTORSPORT VEHICLE BRAKES: INFORMATION Inform the customer during a consultation that the M Compound (standard equipment) and M Carbon Ceramic (optional) brakes are high-performance brake systems which are designed for sporty dynamic driving styles. As a side effect of the highest possible brake performance customers are likely to hear noises due to the extremely resilient materials.
• 10165266SECURITY IMPROVEMENTS FOR CONNECTEDDRIVE. Security patches for non-safety critical vulnerabilities in BMW head units Entry Nav Entry Media NBT and NBT EVO.
• 10163033NEW REPLACEMENT FUEL TANK INTERNAL FUEL LINE CONNECTION. INFORMATION WARRANTY INFORMATION Not applicable. This Service Information bulletin provides technical and repair procedure-related information.
• 10163029N55 ENGINE: FC 28A0 OR 101F01 THROTTLE VALVE OPENING ANGLE. The engine malfunction warning is illuminated and one of the following fault codes are stored in the DME shortly after programming the vehicle or with a customer complaint.
• 10163027ENGINE VIBRATIONS OR NOISE This Service Information bulletin replaces SI B11 01 19 dated February 2019.
• 10163026N63 ENGINE: OIL CONSUMPTION CLASS ACTION SETTLEMENT DIAGNOSIS AND REPAIR PROCEDURES. While engine oil consumption may create a customer inconvenience in the short term it should not cause any drivability problems that would prevent normal day-to-day operational use of the vehicle.
• 10152664"Carbon Ceramic Brake Noise. INFORMATION ""M"" vehicles are designed for high-performance, spirited driving. To accommodate this type of driving profile, a braking system which exceeds the standards for handling heavy brake forces, extreme temperatures, and excellent stopping power at high speeds is required. ""M"" vehicles can be ordered with the optional ultra high-performance braking system, featuring perforated carbon ceramic brake discs designed for circumstances similar to those encountered on racetracks. The carbon ceramic brakes were designed to improve braking efficiency, and dramatically increase braking performance along with a significant reduction in weight. When developing the carbon ceramic brake system, the main focus was on braking performance for the sporty-minded driver, while accepting the comfort limitations of functional noises at slower speeds and when coming to a stop. Please inform the customer that the carbon ceramic brake system's functional noises (squealing/honking), are a known characteristic for this type of material, and are only a small trade-off for the improved braking performance. These functional noises have no effect on the performance, operational reliability and durability of the brakes. Part replacement will not provide a remedy for the noise; this is a known characteristic of the high-performance brake system. More information on the performance and operation of these brakes can be found in the Owner's Manual under ""M carbon ceramic brake."" WARRANTY INFORMATION Not applicable."
• 10152317Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller.
• 10152306"N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump. If injectors need to be replaced, enter the VIN of the vehicle into the ETK and select the part numbers found on screen 13_1416: ""High-pressure rail/injector/mounting."" Always enter the VIN for the vehicle into ETK when searching for parts. When the ETK is corrected, this SIB will be updated. WARRANTY INFORMATION Not applicable. [ Copyright (c)2015 BMW of North America, Inc. ] https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/224...5/4/2015"
• 10152305Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ? FC 193208 Fuel level, plausibility: deviation between consumption and level change Please proceed to the Procedure section. Vehicles with option 610 (Head-Up Display) are not affected. Please follow the ISTA/D test plan for the applicable faults stored in the DME, including the one listed in this bulletin. CAUSE A software error in the instrument cluster causes the fuel gauge to incorrectly update while refilling. The error occurs when the vehicle is powered up after refilling.
• 10151355"N55 - ENGINE MALFUNCTION WARNING DUE TO VAPOR FORMING IN THE FUEL SYSTEM This Service Information bulletin supersedes SI B12 05 16 dated April 2016. The Engine ""Drivetrain Malfunction"" Check Control warning is displayed and the Service Engine Soon (MIL) Lamp may also be on. In areas where winterized fuel is used, this situation may occur after prolonged periods of engine idling or ""stop and go"" driving. Additional symptoms that may be present: rough running poor engine performance difficulty in starting the engine. Either or both of the following fault codes can be stored in the DME. 11A002 - Fuel high pressure, plausibility: Pressure too low 11AC02 - Fuel high pressure, plausibility, cold start: Pressure too low In addition any of the following faults may also be stored: 119404 - Rail pressure sensor, signal: Permanently stuck 118001 - Mixture control: mixture too lean 118401 - Mixture control: mixture too lean; large deviation Vapor formation in the fuel system from fuel quality characteristics of certain winter fuel blends along with high engine compartment temperatures."
• 10151312Troubleshooting intermittent Steering Assistance with Electric Power Steering (EPS). Intermittent steering assistance failure CAUSE The power supply of the EPS control unit.
• 10151068This Service Information bulletin supersedes SI B07 03 14 dated October 2015. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Fault codes stored in vehicles being serviced are not being diagnosed, leading to repeat repair visits (source- Analysis of FASTA data and repeat repair visit reports). INFORMATION Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) to find their root cause during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
• 10149961?ENGINE LEAK DIAGNOSIS ON TURBOCHARGED V8 ENGINES. When diagnosing an engine oil leak or a coolant leak on turbocharged V8 engines it is necessary to use a borescope to identify if the source of the leak is from under the turbochargers. Engine oil or coolant leaking from the bell housing area or the front timing chain cover area may be caused by the turbocharger itself, a turbocharger oil/coolant feed line or turbocharger oil/coolant return line. Do not remove the transmission and do not dissemble the engine before performing this inspection. If necessary, use engine oil leakage detection dye.
• 10149382iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
• 10149381Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
• 10149379Headunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA diagnosis. Software error in the HU-H
• 10149378LED Low Beam Flashes Briefly After Ignition Switched ON. 1. The low beam flashes briefly after the ignition is switched ON. This situation can be duplicated every time the vehicle is started. 2. One of the faults below is stored and currently present: 0xDA1411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC 0xD9D411 - Signal (status of exterior light operation, 0x1AE) invalid, transmitter FRM / FEM / BDC Faulty LED main light module (LHM2)
• 10149377Adaptive Headlight Malfunction. A headlight malfunction CC message is displayed for one or more of the following lights: -Daytime driving light -Turn indicator -Dipped headlight -Main beam The following fault codes in the FRM are stored: -800FC8 LIN bus, headlight driver module (TMS), left: communication fault -E58522 No message (status, exterior lights, front electronics 1, left, 0x1E0), receiver FRM, transmitter TMSL Software error in TMS 3 (headlight driver module AHL); a software I-level lower than 14-07-503 will cause the above situation to occur.
• 10149355. INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
• 10149222N63T AND S63T ENGINE: VALVE SEAL REPLACEMENT. This SI provides a new tool and a new procedure for the N63TU valve seals replacement. Please refer to the following applicable SIBs before replacing the valve seals. SI B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs SI B11 01 13 - N63 and N63TU Engines: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity SI B11 03 13 - Engine Oil Consumption (all models) SI B11 04 13 - N63TU Engine: Engine Oil Consumption If the valve seals are leaking, one of the following will help determine if the seals should be replaced. Smoke from the tailpipe when starting or aggressively accelerating and decelerating the engine Excessive engine oil consumption Spark plugs fouled with engine oil
• 10148428Vehicle inTransport Mode Cannot Be Unlocked with Remote Control. When the vehicle is in transport mode, intermittently it cannot be unlocked via the remote control key. CAUSE When the vehicle is in transport mode, to reduce power consumption, the software is designed to disable the outside antenna receiver from waking up the vehicle.
• 10148427Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue. Cause 1: Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher Cause 2: Calibration data for dimming the Central Information Display (CID) at high temperatures or bright sunlight is set incorrectly internally in the CID Affected Central Information Displays were manufactured from 02/01/2013 to 06/09/2014. The manufacturing date is included in the serial number printed on the parts label on the CID. IMPORTANT: The manufacturing date is written in the following way: dd mm yy Example: The manufacturing date of August 15, 2013 is printed on the label in the following way: 15 08 13
• 10148421This Service Information bulletin supersedes SI B51 33 14 dated October 2014. designates changes to this revision SUBJECT New "Gas Door Operation" Instruction Label. Initial quality reports show the customers are not certain how to open and close the fuel filler flap.
• 10148381Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.

Every BMW R1200 S Adventure model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.