2000 Chevrolet G Van

Owner complaints

What owners report most

1. Electrical system1
2. Fuel/propulsion system1
3. Service brakes, hydraulic1

Latest complaints

• Nov 20, 2015PA120,000 mi
  Electrical system
  TL* the contact owns a 2000 chevrolet g van. While driving at various speeds, the vehicle stalled. The contact was able to restart the vehicle. The failure recurred on numerous occasions. The vehicle was taken to an independent mechanic who diagnosed that the wiring harness and ignition system…

  TL* the contact owns a 2000 chevrolet g van. While driving at various speeds, the vehicle stalled. The contact was able to restart the vehicle. The failure recurred on numerous occasions. The vehicle was taken to an independent mechanic who diagnosed that the wiring harness and ignition system needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure. The failure mileage was 120,000.

• Jun 22, 2015WI106,000 mi
  Fuel/propulsion system
  TL* the contact owns a 2000 chevrolet g van. The contact stated that the fuel gauge did not display the accurate amount of fuel. The failure recurred constantly. The vehicle was taken to an independent mechanic where it was diagnosed that the fuel sending unit needed to be replaced. The vehicle was…

  TL* the contact owns a 2000 chevrolet g van. The contact stated that the fuel gauge did not display the accurate amount of fuel. The failure recurred constantly. The vehicle was taken to an independent mechanic where it was diagnosed that the fuel sending unit needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure. The failure mileage was 106,000. updated 09/03/2015*lj the consumer stated the vehicle can run out of gas without warning. updated 12/16/2015*js

• Dec 19, 2000KYFire
  Service brakes, hydraulic › Antilock/traction control/electronic limited slip

  The vehicle has been serviced numerous times at the dealership for the ABS system and related problems (locking up, pulsation noises, tire noises, tires smoking while the vehicle IS driving due to dragging brakes), the van had flames coming out from under the van the wiring had melted and the ABS brake wiring on both sides had completely burned up. *Mjs

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Hydraulic pump failres

  EA04012Opened Apr 30, 2004Closed Feb 28, 2005Recall 05V005000
  Gm IS conducting a recall on all subject vehicles build between may 1999 and october 14, 1999.significant changes were incorporated into production in early october 1999, and vehicles built after that date have lower warranty failure rates.the complaint and warranty data appear to support the effectiveness of these…

  Gm IS conducting a recall on all subject vehicles build between may 1999 and october 14, 1999.significant changes were incorporated into production in early october 1999, and vehicles built after that date have lower warranty failure rates.the complaint and warranty data appear to support the effectiveness of these changes. Gm made additional changes in november 1999, february 2000, may 2001, and february 2004.odi will continue to monitor this problem and will take further action, if warranted, in the future.for further technical details see the attached engineering analysis report.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006621Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
• 11006421GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
• 11004761This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 11004557This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 11002312This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
• 10251890This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10250775This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10249590This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 10249579This PI bulletin advises the technician on the proper way to install the pistons in an engine.
• 10248444Vehicle Recalls
• 10247552This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
• 10246952Programming And Activation Of Replacement OnStar Modules.
• 10246951Programming And Activation Of Replacement OnStar Modules.
• 10245951Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
• 10245950Canadian Customers Unable To Place Calls In The United States
• 10244274This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10242843The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
• 10242262This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
• 10235799This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10234110This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10232287This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
• 10232136This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
• 10228888This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
• 10227056This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10225615This service bulletin provides information on Module Harvesting.
• 10222839This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
• 10222796This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10220319This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
• 10219266This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
• 10214869This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10209980This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10209921This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10201115OnStar Voice Fallback Number Update
• 10190934Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190933Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190932Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190931Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190512OnStar Voice Fallback Number Update Some customers may have received a letter from OnStar stating that "We recently tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."
• 10171878This informational bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10083900This preliminary information communication advises the technician, if unable to place an onstar call in the ignition on mode after the onstar canada upgrade to contact the gm technical assistance center onstar group for further assistance.

Every Chevrolet G Van model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.