2000 Chevrolet Yukon XL

Owner complaints

What owners report most

1. Fuel system, gasoline1
2. Service brakes1

Latest complaints

• Nov 12, 2013PA142,000 miCrash
  Service brakes
  Two minutes after exiting the pa turnpike driving through my neighborhood. Had to stop at the sign on my corner. Applied brakes but line burst and pedal went to floor. Car would not stop but fortunately was able to navigate the turn and coast to my home while downshifting (automatic) and applying…

  Two minutes after exiting the pa turnpike driving through my neighborhood. Had to stop at the sign on my corner. Applied brakes but line burst and pedal went to floor. Car would not stop but fortunately was able to navigate the turn and coast to my home while downshifting (automatic) and applying the emergency brake. Narrowly avoided hitting a car at the intersection. Then inspected the vehicle and discovered that the brake line was corroded, causing brake fluid to leak from the vehicle. The vehicle has yet to be repaired. contacted GMC citing: http://www.10news.com/money/consumer/more-gm-owners-report-brake-line-rust08092013 and looking for the ?gm spokesman alan adler now says us a repair kit IS finally available through dealers, that lowers replacement cost for customers from almost $2,000 to just $500.? opened service request with GMC on 11/1/13 now GMC indicates that the part IS not available and referred me to my local dealer. Local dealer (o?neil GMC) indicated that all lines need to be fabricated, labor was quoted at approx. 15 hrs @ $110/hr and calipers often have to be replaced as well (they won?t know until the job) estimated $2-3000 for the repair. 11/11/13 received a voice mail from GMC indicating that the case will be escalated. car still sits and now with expired pa inspection. *tr

• Jul 27, 2005AL
  Fuel system, gasoline › Delivery › Fuel pump
  2000 GMC yukon XL had gas pouring out from underneath the vehicle.*mr after the consumer filled up his gas tank fuel began to leak onto the ground at the gas station. the vehicle was towed to a repair facility where it was determined that the fuel tank wiring had burned inside the fuel tank.…

  2000 GMC yukon XL had gas pouring out from underneath the vehicle.*mr after the consumer filled up his gas tank fuel began to leak onto the ground at the gas station. the vehicle was towed to a repair facility where it was determined that the fuel tank wiring had burned inside the fuel tank. this IS the vehicle's second fuel pump failure. in may 2005 the consumer received a letter from the manufacturer concerning the fuel pump wiring failure. the letter explained that the manufacturer was working with the supplier to develop and obtain a service kit to permanently correct the problem. *nm

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Brake line corrosion failure

  EA11001Opened Jan 5, 2011Closed Apr 8, 2015
  On January 11, 2011, ODI opened EA11-001 to investigate allegations of premature brake line corrosion failure in model year (MY) 1999 through 2003 General Motors (GM) full-size pickup trucks and sport utility vehicles sold or registered in the following region of the United States that NHTSA has viewed as salt states…

  On January 11, 2011, ODI opened EA11-001 to investigate allegations of premature brake line corrosion failure in model year (MY) 1999 through 2003 General Motors (GM) full-size pickup trucks and sport utility vehicles sold or registered in the following region of the United States that NHTSA has viewed as salt states for investigations of corrosion related issues:Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia and Wisconsin.The subject vehicles represent the first five MY's of GM's GMT800 platform production, of which approximately 2,038,504 vehicles were sold in salt states (the subject vehicles).The GMT800 platform includes the following vehicles:1999-2007 Chevrolet Silverado and GMC Sierra 1500, 2500 and 3500 series pick-up trucks; 2000-2006 Chevrolet Suburban, Chevrolet Tahoe and GMC Yukon sport utility vehicles; and 2002-2006 Cadillac Escalade and Chevrolet Avalanche sport-utility vehicles.General Motors produced a total of approximately 10,427,062 GMT800 vehicles for sales in the United States, including almost 5 million that were sold in salt states.Although there are over 60 different brake pipe routing configuration used in GMT800 vehicles, with the exception of the rear crossover pipes in MY 200x-2007 vehicles that changed from rear disc to drum brakes, all of the vehicles use brake pipes from the same supplier with a common double-wall, brazed steel pipe design with a combination of hot dip Zinc-Aluminum corrosion protection coating and Aluminum paint outer layer known in the industry as AlGal (ASTM-B750). ODI analysis of field data regarding GMT800 vehicles identified a total of 3,645 complaints of brake pipe corrosion failures, including 107 alleging crashes, and 40 injuries.Though only 20% of total GMT800 production, due to age and region the subject vehicles account for a disproportionate share of the failure experience; with 2,702 of the complaints (75%), 88 of the crashes (82%) and 20 of the injuries (50%) reported in those vehicles.Analysis of the complaints showed strong correlations to vehicle age and region.For vehicles with less than 8 years of service, the complaint rates were minimal for all regions.In the salt states the failure rates begin to climb as the vehicles advance in age, particularly in the Northeast corner of the United States.The complaint rates in the salt states go from less than 0.1 incident per thousand vehicles (IPTV) at 7 years in service to over 1.0 IPTV after the 12th year of service for the subject pickup trucks and utility vehicles.Most of the failures reported to ODI occurred in vehicles with more than 10 years in service.ODI?s investigation did not identify any specific defect conditions that were causing or contributing to the brake pipe failures.Nor did the analysis isolate the problem to any subject vehicle sub-populations when analyzed by vehicle type or production range.The investigation found that vehicles experiencing brake pipe corrosion failures were likely to have general patterns of excessive corrosion on the majority of the brake pipe assembly and appear to be occurring due to expected wear out for the brake pipe coating material used in the subject vehicles and the environmental conditions in severe corrosion states.A safety-related defect has not been identified at this time.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor t

• Parking brake failure

  DP05009Opened Dec 20, 2005Closed May 31, 2006

  Odi's review of complaint data received since the close of ea04-011 revealed no indication that the investigation should be re-opened.more details can be found in the federal register notice enclosed in the dp05-009 public file.odi reserves the right to reopen the investigation in the future should conditions warrant.

• Unwanted low-speed ABS activation

  PE05020Opened Apr 28, 2005Closed Sep 13, 2005Recall 05V379000
  In a letter dated august 29, 2005, gm notified odi that it was recalling certain model year 1999 through 2002 c/k pickup trucks and sport utility vehicles to correct a problem with anti-lock brake system (ABS) wheel speed sensor corrosion that may result in unwanted ABS activation and extended stopping distances…

  In a letter dated august 29, 2005, gm notified odi that it was recalling certain model year 1999 through 2002 c/k pickup trucks and sport utility vehicles to correct a problem with anti-lock brake system (ABS) wheel speed sensor corrosion that may result in unwanted ABS activation and extended stopping distances during low-speed braking (recall 05v-379).gm's recall covers approximately 804,000 vehicles currently registered in the following 14 salt-belt states:connecticut, illinois, indiana, massachusetts, maine, michigan, new hampshire, new jersey, new york, ohio, pennsylvania, rhode island, vermont, and west virginia.the recall procedure will involve removing the sensor, cleaning the mounting surface, applying a rust inhibitor (zinc-x) to the surface, and reinstalling the sensor.if necessary, the sensor will be replaced. The population and failure report data given in this resume are for the full region that has been considered by odi as the salt-belt.that includes delaware, iowa, maryland, minnesota, missouri, wisconsin and the district of columbia in addition to the 14 states included in 05v-379.the states covered by gm's recall have the highest incident rates for the subject condition, accounting for 91% of the incidents, but only 24% of subject vehicle sales in the united states.odi's analysis determined that 840 of the complaints, 244 of the crashes, and 16 of the injuries identified in this investigation occurred in those states.the resulting incident and crash rates are 96.2 and 28.0 per 100,000 vehicles respectively (note:rates are based on vehicle sales, not registered vehicles). The corresponding numbers in the excluded portions of the salt-belt are 399,000 vehicles, 81 incidents (20.3 per 100,000 vehicles), 3 crashes, and no injuries.the statistics in the remaining 30 states are 2,406,000 vehicles, 168 incidents (7.0 per 100,000 vehicles), 31 crashes, and one injury.gm and odi are continuing to monitor the problem experience in states that are not included in the recall.gm will provide odi with updated complaint, field report, and warranty data in november 2005.odi and gm will review that data and assess the appropriateness of the current scope of the recall at that time.

• Hydraulic pump failres

  EA04012Opened Apr 30, 2004Closed Feb 28, 2005Recall 05V005000
  Gm IS conducting a recall on all subject vehicles build between may 1999 and october 14, 1999.significant changes were incorporated into production in early october 1999, and vehicles built after that date have lower warranty failure rates.the complaint and warranty data appear to support the effectiveness of these…

  Gm IS conducting a recall on all subject vehicles build between may 1999 and october 14, 1999.significant changes were incorporated into production in early october 1999, and vehicles built after that date have lower warranty failure rates.the complaint and warranty data appear to support the effectiveness of these changes. Gm made additional changes in november 1999, february 2000, may 2001, and february 2004.odi will continue to monitor this problem and will take further action, if warranted, in the future.for further technical details see the attached engineering analysis report.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010544This service bulletin explains how to measure for oil consumption and possible reasons for loss of oil.
• 11006621Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
• 11006421GM is receiving damaged (cracked or broken) transmission cores returned to the reman facilities. The damage is being caused either in the removal process by the technician, or inadequate packaging or shipping. This bulletin advises the dealers to be more careful not to damage the transmissions during removal and to package the core properly for return.
• 11004761This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 11004557This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 11002312This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
• 10251890This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10250775This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10249590This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 10249579This PI bulletin advises the technician on the proper way to install the pistons in an engine.
• 10248444Vehicle Recalls
• 10247552This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
• 10246952Programming And Activation Of Replacement OnStar Modules.
• 10246951Programming And Activation Of Replacement OnStar Modules.
• 10246624Car and Truck Fix it Right the First Time Issues
• 10245951Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
• 10245950Canadian Customers Unable To Place Calls In The United States
• 10244274This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10242843The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
• 10242262This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
• 10235799This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10234110This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10232287This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
• 10232136This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
• 10228888This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
• 10227056This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10225615This service bulletin provides information on Module Harvesting.
• 10222839This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
• 10222796This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10220319This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
• 10219266This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
• 10214869This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10209980This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10209921This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10201115OnStar Voice Fallback Number Update
• 10190934Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190933Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190932Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190931Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190512OnStar Voice Fallback Number Update Some customers may have received a letter from OnStar stating that "We recently tried to provide a software update to the OnStar hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer or any dealer near you as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F."