2017 Ford E-550

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
• 10240743The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
• 10164497For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable clamp and clean the cable end as necessary to preserve wire length. Some rework may be necessary for some vehicle environments. Bend the new positive battery cable clamp as needed and crimp it to the existing battery cable. Make sure to use heat shrink tubing over the battery cable to battery cable clamp connection. Obtain the heat shrink tube locally.
• 10159489Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
• 10155575Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
• 10155574Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
• 10138524The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
• 10127405Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
• 10117902Affected vehicle list fo 17B08 customer satisfaction program
• 10117901Ford Customer Satisfaction Program 17B08 concerning certain vehicles equipped with 6.8L engine. Notifying customers of potential loose crankshaft pulley bolt and recommending servce action by Ford dealer.
• 10100082The 2017 powertrain control/emissions diagnosis (pc/ed) manual has been revised for diagnosing electronic throttle body (etb). For all etb concerns, the appropriate diagnostic must be completed before throttle body replacement. If a concern IS intermittent and no dtcs are present, refer to historical dtcs and the pc/ed, section 3 no dtcs present index chart for further information.
• 100994632009-2017 vehicles equipped with a 6R80, 6r100, 6r140 automatic transmission have an updated main control valve body overhaul procedure. Refer to workshop manual (wsm), section 307-01 for main control valve body (7a100) overhaul procedures. Not all valve bodies require replacement. Inspect the valve body bores, springs and valves as directed during diagnosis and repair. Refer to general service bulletin (gsb) g0000093 automatic transmission main control inspection for a video clip to aid in the diagnosis of these repairs.
• 10099458Some vehicles may exhibit an illuminated mil with diagnostic trouble codes (dtcs) p0011, p0012, p0014, p0015, p0016, p0017, p0018, p0019, p0021, p0022, p0024 and/or p0025. This may be due to small debris causing the vct solenoid to stick. Before attempting any component diagnosis or replacement of the vct solenoid, refer to powertrain control and emissions diagnosis (pc/ed) pinpoint test HK11 to cycle the affected vct solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6m280 and applicable labor operations in section 10 of the service labor time standards (slts) manual.
• 10094625The 2017 powertrain control/emissions diagnosis (pc/ed) manual has been revised for diagnosing electronic throttle bodies (etbs). For all etb concerns, the appropriate diagnostic must be completed before throttle body replacement. If a concern IS intermittent and no dtcs are present, refer to historical dtcs and the pc/ed, section 3 no dtcs present index chart for further information.
• 10094592Some 2016-2017 e-series 350/450 vehicles equipped without a traction control switch and built on or before 17-feb-2016 may have traction control function or traction control related symptoms. Vehicles without a traction control switch are not intended to have traction control. Reprogram the powertrain control module (pcm) to the latest calibration using ids release 103.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

Every Ford E-550 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.