2024 Ford F-600 SD

Recalls

2 recalls name the 2024 Ford F-600 SD. Newest first.

• Electrical system › Integrated trailer brake control

  Feb 20, 2026NHTSA 26V1040004,381,878 vehicles

  Ford Motor Company (Ford) is recalling certain 2021-2026 F-150, 2022-2026 F-250 SD, F-350 SD, F-450 SD, F-550 SD, Maverick, 2024-2026 Ranger, 2023-2026 F-600 SD, 2022-2027 Lincoln Navigator, Expedition, and 2026 E-Transit vehicles. When towing a trailer, the integrated trailer module (ITRM) may lose communication with the vehicle, possibly causing a loss of…

  Risk and remedy

  Risk

  Trailer lights or brakes that do not function can reduce the driver’s ability to control the trailer and decrease the trailers visibility to other road users, increasing the risk of a crash.

  Remedy

  The integrated trailer module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed March 25, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C10. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning March 17, 2026.

  Full recall details →

• Back over prevention › Software

  May 9, 2025NHTSA 25V3150001,076,138 vehicles

  Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to…

  Risk and remedy

  Risk

  A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.

  Remedy

  The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.

  Full recall details →

Owner complaints

Latest complaints

• Jun 30, 2025CA2,950 mi
  Engine
  The contact owns a 2024 Ford F-600SD. The contact stated while driving 65 MPH, the vehicle lost automotive power. The contact shifted into neutral, restarted the vehicle, shifted into drive while looking for a safe place to pull over; however, the failure persisted. The contact stated that after…

  The contact owns a 2024 Ford F-600SD. The contact stated while driving 65 MPH, the vehicle lost automotive power. The contact shifted into neutral, restarted the vehicle, shifted into drive while looking for a safe place to pull over; however, the failure persisted. The contact stated that after several attempts to restart the vehicle, the vehicle was drivable. A dealer was contacted. The contact stated that the check engine warning light was illuminated. The vehicle was taken a dealer to be diagnosed; however, the result was unknown. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was referred to the NHTSA Hotline for assistance. The failure mileage was 2,950.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006775Some 2024 F-Super Duty/F-150 vehicles may exhibit a concern where the vehicle's center display screen gets stuck in a reboot loop of the Ford logo and eventually goes black. This may be due to a concern with the software on the telematics control unit module (TCU). To correct the condition, follow the Service Procedure to reprogram the TCU and then perform a battery disconnect to make sure the accessory protocol interface module (APIM) receives the correct date from TCU.
• 11006774Some 2023-2024 F-Super Duty vehicles built on or before 22-Jul-2024 and equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P203B, P206B, and/or P2201:92 stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool.
• 11001575This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
• 11001368When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
• 11001148Certain 2023-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine - Powertrain Control Module Software Update
• 110011132023-2024 F-Super Duty/F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2023-2025 F-650/F-750/E-Series vehicles equipped with a Dana rear axle and built on or after 01-Nov-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.
• 11001112Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information.
• 11000297Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
• 11000288Some 2023-2024 F-Super Duty vehicles built on 22-May-2023 and through 15-Dec-2023 may require repairs of the power steering system for various reasons. If repairing a power steering fluid leak at or near the power steering fluid cooler, a worm clamp (part number 376240-S100) can be used adjacent to the factory clamp in lieu of steering hose replacement for any power steering hoses affected by the repair.
• 10254140Some 2023-2024 F-Super Duty vehicles may exhibit various diagnostic trouble codes (DTCs) related to the steering angle sensor. Prior to any diagnosis, determine if the vehicle is equipped with an electronic steering actuator (ESA), also referred to as the power steering control module (PSCM), so appropriate pinpoint tests are followed. The ESA is located on the steering shaft and can be seen through the left fender opening or under the hood near the driver's side frame rail. Refer to the Workshop Manual (WSM), Section 211-02 for images as needed. For vehicles equipped with an ESA, the steering angle sensor is integrated into the ESA. For vehicles not equipped with ESA, the steering angle sensor is integrated into the steering column control module, behind the clockspring. The pinpoint tests for the steering angle sensor in the WSM will specify what test or steps to follow based on presence of ESA. Failure to follow the proper pinpoint test may lead to improper diagnosis and repair.
• 10254138All accessory stick-on keyless entry keypads come with a wallet card containing the master code. If the accessory keypad was factory installed, this card will be placed in the glove box and should be handed to the vehicles owner during initial delivery. Unlike the integrated (wired) factory keypad, the accessory keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool. If the wallet card for an accessory keypad is lost, follow these steps to recover the code. Dealer Key Code access is granted through the Dealer Program Enrollment System (DPES); dealership management can authorize users. The authorized user must go to FMCDealer.com > Parts and Service > Parts Product Line Information > Keys/Entry Devices > Aftermarket Keyless Entry Keypad Code Access. Follow the instructions on the screen to obtain the master code for the accessory keypad.
• 10254133Some 2022 F-Super Duty vehicles equipped with a 12.3 inch center display screen and 2023-2024 F-Super Duty vehicles may exhibit DTCs B1D08 and/or B1D09 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Disconnect connector C4099 from the back of the trailer tow connector (14489). Inspect connector C4099 and the mating socket on the back of the trailer tow connector for signs of corrosion or damage. If corrosion or damage is present at either connector, replace both the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 13A576 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual.
• 10254127Some 2023-2024 F-Super Duty/F-53 Motorhome/F-59 Commercial Stripped Chassis or 2023-2025 E-Series/F-650/F-750 vehicles equipped with a gas engine may exhibit an illuminated MIL with ignition system DTC(s) P0352, P0353, P0354, P0355, P0357, P2303, P2306, P2309, P2312, P2318, P2304, P2307, P2310, P2313, P2319, and/or P2322 set in the powertrain control module (PCM). This may be due to incorrect cylinder to DTC mapping within the PCM. This means the DTCs listed may set against the incorrect cylinder. Even though the cylinder to DTC mapping is incorrect in the PCM, the presence of these DTCs means that a real ignition system concern is present that requires diagnosis and repair. Prior to performing a pinpoint test for one of the listed DTCs, it will be necessary to identify the correct cylinder that has the issue. Do this by using the Ford diagnosis and repair system (FDRS) to perform a cylinder power balance test. If the results show two cylinders dropping out, begin diagnosing the ignition system components for the cylinder that is dropping out and not setting an ignition related DTC. Due to the incorrect incorrectcylinder to DTC mapping, the PCM will shut off fuel to the cylinder that the PCM has triggered a DTC against. Diagnosing the cylinder that does not set an ignition DTCand drops during the power balance test, will verify the identity of the cylinder that has the concern. If only onecylinder is dropping out, start diagnostics with that cylinder. Refer to the Workshop Manual, Section 303-07A/C.
• 10253682Some 2023-2024 F-Super Duty vehicles equipped with a perimeter alarm and built on or before 27-Mar-2024 may exhibit a false alarm activation intermittently. This may be due to the software in the body control module (BCM). Monitor the BCM alarm event parameter identifications (PID). If ALARM_EVT_1/2/3/4 show a value of Intrusion Sensor, reprogram the BCM using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 15604 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10253557Some 2024 F-Super Duty non-Tremor vehicles equipped with four-wheel drive (4WD) may exhibit a slight rotational grinding noise from the front axle while driving in two-wheel drive (2WD). If the noise does not occur with the vehicle driven in 4WD, this may be due to the non-selectable right side hublock on the front axle. To correct the condition, replace the right front hublock with a selectable hublock, service part number PC3Z-3B396-A. Refer to Workshop Manual (WSM), Section 307-07A. Vacuum lines with service base part numbers 3C125 and/or 3C124 may need to be installed if not present on the vehicle. Refer to the parts catalog. Suspension modifications may contribute to the concern. Inspect the vehicle for aftermarket levelling or lift kits as well as aftermarket caster/camber adjusting sleeves. If any vehicle modifications are present, this is not a warrantable repair. Do not submit a claim. Use the Report a Vehicle Concern link at the bottom of the OASIS report to submit a report detailing the presence or lack of aftermarket equipment with photos attached to the report. Reference this article by number in the text of the report.
• 10253556Some 2023-2024 F-Super Duty vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2122, P2123, P2127, P2128, and/or P2138 stored in the powertrain control module (PCM). The vehicle may or may not exhibit a perceived lack of power intermittently. Perform a wiggle test of connector C1580 at the left rear of the engine compartment while the engine is at normal operating temperature. Perform a visual inspection of pins 18 through 29 as well as a terminal fit test using the appropriately sized flex probe. Repair as necessary. Refer to Wiring Diagram Cell 005. If no concerns are found, refer to Workshop Manual (WSM), Section 310-02 for normal diagnostics.
• 10252647Some 2022-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) U3012 stored in the PCM. If no drivability concerns or other DTCs are present, perform normal diagnostics per the Workshop Manual (WSM). If diagnostics lead to the powertrain control module (PCM) or body control module (BCM), the replacement of the PCM and/or the BCM will not resolve this concern. This illuminated MIL with DTC U3012 does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
• 10252627Some 2023-2024 F-Super Duty vehicles equipped with a trailer brake control module may exhibit a Trailer Disconnected message after cycling the ignition off and back on with a trailer connected. This may be due to the presence of an integrated battery charger on a trailer equipped with electric over hydraulic brakes. If trailer functionality is restored after unplugging and plugging the trailer connector back in while the ignition is on, this condition can be corrected by downloading and performing the Trailer Brake Configuration application using the latest version of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. For claiming, use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10252626Some 2021-2024 Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may exhibit water coolant pump leaks. This may be due to contamination in the coolant system. To correct this condition and prevent recurrent water pump failures, perform a coolant system flush. Refer to the Workshop Manual (WSM), Section 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures > Engine Cooling System Flushing > Steps 1-8. Then replace the coolant pump. Refer to the WSM, Section Engine Cooling - 1.5L EcoBoost > Removal and Installation. Fill and bleed the coolant system properly. Refer to the WSM, Section 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures > Engine Cooling System Draining, Vacuum Filling and Bleeding. Note: Repeat steps 10-12 a total of 10 times to remove any remaining air trapped in the system.
• 10252546This TSB supersedes article 24-2036 to update the vehicles affected. Some 2023-2024 F-Super Duty pickup vehicles built on or before 02-Jan-2024 equipped with a 6.7L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0133, P0139, and/or P0145 stored in the powertrain control module (PCM). This may be due to the software in the PCM and does not affect vehicle operation.
• 10251956Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
• 10251952For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
• 10251947Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
• 10251934During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.

Every Ford F-600 SD model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.