2016 Freightliner Sprinter 4500

Recalls

1 recall names the 2016 Freightliner Sprinter 4500. Newest first.

• Steering › Hydraulic power assist › Hose, piping, and connections

  Oct 28, 2020NHTSA 20V66300047,667 vehicles

  Daimler Vans USA, LLC (DVUSA) is recalling certain 2015-2020 Mercedes Benz Sprinter and Freightliner Sprinter vehicles. The hydraulic power steering return line hoses may detach at their connection points under certain operating conditions, causing hydraulic fluid to leak.

  Risk and remedy

  Risk

  The sudden loss of power steering assist and hydraulic steering fluid leaking onto the roadway may increase the risk of a crash.

  Remedy

  DVUSA will notify owners, and dealers will check the return line connections of the power steering system, correcting it as needed, free of charge. The recall began December 23, 2020. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA's number for this campaign is NV3LETULPE.

  Full recall details →

Defect investigations

NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.

• Desiccated Air Bag Inflator Rupture

  EA21002Opened Sep 17, 2021Open
  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…

  From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11011223SMOG/Emissions Test fail due to one or more Readiness Monitors not set Complaint: The vehicle has failed the State Emissions Certification because one or more of the OBDII readiness monitors are not completely set. Cause: One or more of the following Readiness Monitors are not fully set within XENTRY: Misfire Monitoring - Injection System Fuel System Monitoring - Injection System, Fuel System, EGR Valve, O2 Sensor NMHC Catalyst Monitoring - NMHC/Diesel Oxidation Catalyst NOx Aftertreatment Monitoring - SCR Catalyst System Boost Pressure System Monitoring - Turbocharger, Charge Air System Exhaust Gas Sensor Monitoring - O2 Sensor, NOx Sensors Diesel Particulate Filter Monitoring - Diesel Particulate Filter System Exhaust Gas Recirculation System Monitoring - EGR Valve and system Remedy: Please complete the required driving conditions to fully set the incomplete Readiness Monitor. DO NOT: - Erase any fault codes. If fault codes are present, process these and allow the readiness drives to clear fault codes. - Flash or SCN code the CDI or SCR control units. - Perform a manual DPF regeneration, unless instructed below. - Disconnect the main battery.
• 11001114Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the desired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.
• 10228805Problem: Vehicle fails smog test Cause In the event the Engine Control Module (CDI) detects a fault with the Water Pump Short Circuit to Battery diagnostic, Fault Code P260312 and/or P260315 may set and prevent the readiness monitor from running. Even following a successful repair and/or clearing the Fault Code(s), the readiness monitor remains deactivated and self-healing is not possible. This deactivation may prevent the vehicle from passing state emissions inspection and SMOG Test and is only resolvable by installing new engine control unit software. Remedy 1. Perform XENTRY Quick Test. 2. Check for the presence of Fault Code P260312 and/or P260315 in the CDI control module. 3. If relevant Fault Codes are present, resolve fault using standard dealer procedures. Once fault is resolved, proceed to step 5. 4. If no relevant Fault Codes are present, or the fault has been previously repaired and Fault Codes erased, proceed to step 5.
• 10228611Software Update - Water Pump Diagnostics
• 10227139SMOG Test will not complete successfully. NOTE: Customers may come to dealership as instructed by ISP (Independent Service Provider) based on instructions from a TSB (Technical Service Bulletin). Access to the TSBs can be found via https://www.obdclearinghouse.com/ or by viewing the TSBs in the attachments area of this LI. Cause In the event the Engine Control Module (CDI) detects a fault with the Water Pump Short Circuit to Battery diagnostic, Fault Code P260312 and/or P260315 may set and prevent the readiness monitor from running. Even following a successful repair and/or clearing the Fault Code(s), the readiness monitor remains deactivated and self-healing is not possible. This deactivation may prevent the vehicle from passing state emissions inspection and SMOG Test and is only resolvable by installing new engine control unit software. Remedy 1. Perform XENTRY Quick Test. 2. Check for the presence of Fault Code P260312 and/or P260315 in the CDI control module. 3. If relevant Fault Codes are present, resolve fault using standard dealer procedures. 4. If no relevant Fault Codes are present, or the fault has been repaired and Fault Codes erased, proceed to check and install new Engine Control Unit SW
• 10212902Modification to the emission control system.
• 10212897Modification to the emission control system.
• 10181196Mercedes-Benz USA, LLC (?MBUSA?) has entered into an agreement with the United States Department of Justice (DOJ), the Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and the California Attorney General?s Office (CA AG) regarding the emission control system in certain MercedesBenz diesel vehicles. As part of this agreement, MBUSA will offer field measures referred to as the Approved Emission Modification (?AEM?) for the affected vehicles. As a result, certain vehicles covered under this notification cannot be sold or caused to be sold, or leased or cause to be leased, or introduced into commerce, or exported from the United States to another country, until after the AEM described in this notification is performed. An authorized Mercedes-Benz dealer will install the AEM at a later date at no cost to the Owner/Lessee.

Every Freightliner Sprinter 4500 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.