2001 Geo Prizm

Owner complaints

What owners report most

1. Structure3
2. Engine and engine cooling1
3. Power train1
4. Electrical system1
5. Suspension1
6. Visibility1
7. Wheels1

Latest complaints

• Mar 23, 2006MI63,000 mi
  Structure › Body › Hood › Hinge and attachments

  Dt*: the contact stated while traveling 40 mph on a busy highway the hood on the vehicle blew up and busted the windshield. the vehicle was pulled off to the side of the road and the hood was tied down. the vehicle was taken to the dealership, where it was determined the hinges on the hood were rusted. *ak

• Jun 22, 2004PA
  Engine and engine cooling › Engine

  While driving check engine light came on and remained on. consumer took vehicle to dealership numerous times in the past year for repairs. Each time a repair was done. a couple of days later, check engine light reappeared, and came on at various speeds. Problem was not resolved. *ak

• Apr 5, 2004MN
  Structure

  Interior- front driver side, side of dashboard panel and door frame panel rubbing together that causes interior paint to deteriorate. *nm

• Jun 3, 2003OH
  Electrical system › Wiring › Fuses and circuit breakers

  While the vehicle was in gear, the consumer was able to remove the key from the ignition. The key could not be removed after the fuse was replaced. *ak *cb *jb

• Jun 24, 2002CA
  Power train › Manual transmission

  The transmission IS a manual transmision. Once awhile, when the gear IS shift to rear gear while the car IS in complete stopped. The car move forward instead backward. It happen many times since I purchased new 10 months ago.

• Feb 22, 2002WICrash
  Structure › Frame and members · Suspension › Rear · Visibility › Power window devices and controls · Wheels

  The dealer did not repair the car the right way . And I do not know what to do? No safety defect listed. *Ak

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11006621Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers.
• 11004761This service bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 11004557This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 11002312This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information.
• 10251890This technical bulletin advises of a new fuel injection cleaner kit used for decarbonizing the intake valves to correct conditions of rough idle, Crank no start, extended crank or misfire, MIL with DTCs, and explains how Top Tier fuels should be used to reduce carbon build-up.
• 10250775This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10249590This bulletin provides information for use on a Product Assistance Claim (PAC), which is formerly known as a Product Allegation Resolution (PAR) claim.
• 10249579This PI bulletin advises the technician on the proper way to install the pistons in an engine.
• 10249011This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage.
• 10248444Vehicle Recalls
• 10247681Information On Requests To Add OnStar Bluetooth Option.
• 10247552This service bulletin provides information on Concerns or Questions Regarding Installation of Dealer Installed Accessories.
• 10246952Programming And Activation Of Replacement OnStar Modules.
• 10246951Programming And Activation Of Replacement OnStar Modules.
• 10246631Expanded Availability for Remanufacture and Return (R&R) Electronic Control Modules
• 10245951Canadian Customers Unable To Place Calls And Turn By Turn Inoperative In The United States.
• 10245950Canadian Customers Unable To Place Calls In The United States
• 10244274This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10244201This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
• 10242843The service bulletin advises the tech of a normal transmission shift condition and the delay in throttle response when the throttle plate is opened rapidly and advises the customer that it is normal for the delay.
• 10242262This service bulletin provides graphics, information and guidelines for engine component wear to assist service personnel as a guideline to perform necessary engine repairs and prevent unnecessary engine replacement.
• 10235799This service bulletin provides information about the Hunter wheel Road Force balancers that should be utilized for all repairs requiring balance and Road Force measurement.
• 10234110This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10232287This warranty administration bulletin provides information regarding the field action courtesy transportation policy.
• 10232136This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines.
• 10228888This service bulletin provides diagnostic tips/steps on testing for possible EVAP leaks in the system to correct a customer concern of an MIL Illuminated with DTCs P0442 and/or P0455 Set.
• 10227056This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10225615This service bulletin provides information on Module Harvesting.
• 10224820This service bulletin provides information for dealers on how to submit a product information report (PIR) (Canada Only).
• 10222839This service bulletin provides information on Handling Requests for Modifications to Permanently Import/Export Vehicles Between the U.S. and Canada.
• 10222796This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10220319This diagnostic tip advises the tech not to separate the flexplate from the torque convertor or damage my occur if the engine is started while diagnosing for noise from the engine or transmission.
• 10219266This bulletin provides information on tools available to find an intake vacuum leak or exhaust leak to correct a condition of MIL Illuminated with Multiple Fuel Trim and/or Oxygen Sensor Codes Set.
• 10214869This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10209980This service bulletin provides service information to technicians on guidelines to replace Oil Cooler, Oil Cooler Lines and Oil Tank if the engine was replaced where large amounts of debris has flowed throughout the oiling system.
• 10209921This service bulletin provides service information on new torque specification and installation procedure for ACDelco Spin-On Oil Filters.
• 10190934Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190933Underbody Component Corrosion The following information may be helpful when addressing underbody component corrosion with customers. Some customers may comment that one or more of their vehicle's underbody components are showing some form of corrosion. This corrosion may be red in appearance (rust) if the component is steel, forged iron or cast iron. This corrosion may also be grey or white in color if the component is constructed of an aluminum alloy.
• 10190932Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.
• 10190931Refinishing Aluminum Wheels This bulletin updates General Motor's position on refinishing aluminum wheels. GM does not endorse any repairs that involve welding, bending, straightening o re-machining. Only cosmetic refinishing of the wheel's coatings, using recommended procedures, is allowed. Evaluating Damage In evaluating damage, it is the GM Dealer's responsibility to inspect the wheel for corrosion, scrapes, gouges, etc. The Dealer must insure that such damage is not deeper than what can be sanded or polished off. The wheel must be inspected for cracks. If cracks are found, discard the wheel. Any wheels with bent rim flanges must not be repaired or refinished. Wheels that have been refinished by an outside company must be returned to the same vehicle. The Dealer must record the wheel ID stamp or the cast date on the wheel in order to assure this requirement. Refer to Refinisher's Responsibility Outside Company later in this bulletin.

Every Geo Prizm model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.