2009 Hino 268

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11000898This article will provide dealership technicians with information on how to open a tech assist case and discuss what is required when opening a Tech Assist Case.
• 11000897After connecting to a truck using DX3, it may be necessary to review or create a DX Diagnostic Report for review.
• 10185585The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 10184170Hino Quick Reference Guide 2005-2010 Model Years
• 10119458TT-16-013 The procedure for installing the rocker shaft bolts into the cam housing has been updated. It is recommended to lightly lubricate the threads and flange of the bolts with clean engine oil before installing them. The torque specification has also been reduced as a result of adding lubricant to the bolts.
• 10119455Tt-16-010 air spring shield
• 10119452TT-16-005 The purpose of the tech tip is to provide information for a low power concern possibly relating to the brake switch. Hino Trucks are equipped with two brake switches. First, a stop lamp switch that is designed to activate stop lamps on the truck. Second, a brake switch that is designed to send brake application input for modules to monitor brake activation. When monitoring DXII with the brake applied, the switches should both read ON and when the brake pedal is released, they should both read OFF. If the brake is not applied (typically when accelerating) and if one switch reads ON while the other reads OFF when the brake pedal is not applied, a brake switch correlation concern is the likely cause. Perform the following to identify the switch with this concern.
• 10119447TT-15-013 To provide a better determination of a DPF?s internal condition, a Special Service Tool (SST) has been developed. An explanation of SST-HDT-650590 and a brief DPF inspection follows below.
• 10118109TT-15-016 The purpose of this publication is to communicate the standard measuring positions on the Hino chassis. In some cases, the customer may report a visual chassis posture concern where the chassis appears to be leaning more towards the driver side or passenger side. The following publication can be referenced to obtain the manufacture?s measurement positions and specifications. Should the truck not meet the specifications, you should consider the following potential causes noted in the inspection guideline section below.
• 1011810507 - 006 voltage drop test
• 10118099SB-13-009 This bulletin is to inform dealers and workshops of proper paint codes for all Hino models. ALL MODELS
• 10118085Sb-11-002 requirements of biofuel usage for 2008my thru 2012my vehicles all applied models
• 10117748SB-16-010 Correction of the inspection of the DPR filter.
• 10117728TT-14-029 A subject vehicle at 200,000 miles may exhibit a "DPR Maintenance" message displayed on the Instrument Cluster message center. The following procedure will instruct how to check the DPF and reset the displayed message.
• 10117723TT-14-021 This procedure illustrates a worst case scenario repair procedure, the process and materials being used are the same for all repairs. Depending on the location of the repair, access may be limited in some cases. Ensure that the repair area extends at least 2 inches on either side of the cracked area.
• 10117680SB-15-026 A subject vehicle may exhibit an engine oil leak or engine coolant leaking externally from the engine head gasket sealing area on the exhaust manifold side of the engine. An improved head gasket has been made available as a service part and should be used if replacement of the head gasket is necessary. Improvement of the head gasket includes the addition of rubber seals around the engine oil and engine coolant port holes.
• 10117678SB-15-022 In the rare event that a subject vehicle equipped with the 23k Comfort Ride air suspension experiences a premature main leaf failure, a 23k HD Comfort Ride air suspension may be installed with PRIOR APPROVAL from HMM QA.
• 10117673SB-15-017 New parts are available to prevent repeat exhaust manifold stud failures on the J05 engine. This bulletin provides instructions for an exhaust manifold attachment modification at the #1 and #4 cylinder locations. Modifications to the manifold insulator shield and the turbocharger water return pipe have also been made to accommodate the longer studs.
• 10117671SB-15-015 Information of Troubleshooting Procedure for Engine Lacked Power during the DPR Automatic Regeneration
• 10117655SB-14-003 The following is to inform you of the revision of the inspection procedure for the DTC?s P0340 and P0341. You are kindly requested to attach this service data to the relevant pages of the workshop manuals for maintenance and to use for servicing.
• 1011603013-008 Injection Pump Drive Case. Please note the following part number changes to the Injection Pump Bearing Case. Not replacing the correct replacement parts WILL result in major engine damage. The Hino Ordering system has been modified to make the below changes into a kit that consist of the correct parts when ordering the kit ID number. The below information illustrates the kit components per engine and date ranges.
• 10116025PTB 01-08 Complete Engine Assembly Part Numbers

Every Hino 268 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.