2008 International 7000
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › 7000 › 2008
These records cover every 2008 International 7000. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
2 recalls name the 2008 International 7000. Newest first.
Navistar IS recalling 51,588 heavy trucks, commercial buses and school buses manufactured between november 21, 2000 and may 21, 2008, equipped with one or more remote power modules. the potting material that encapsulates the circuit board of the vehicle's remote power module may not sufficiently seal the circuit board from water and contamination…
Risk and remedy
Risk
A fire could cause personal injury or death.
Remedy
Navistar will notify owners and repair the vehicles free of charge. the recall began on july 10, 2008. owners may contact navistar at 1-280-461-1890.
International IS recalling my 2008-2009 4000, 5000, 7000, 8000, 9000 and prostar tractor/trucks equipped with bendix MV-3 dash control valves. the molded valve body has an incorrect core pin in the injection mold causing the valve body to be oversized in the double check valve area. this condition can allow the rubber double check valve to become lodged…
Risk and remedy
Risk
If the double check valve becomes lodged, in the event of a primary reservoir failure, air pressure can leak past the lodged double check valve thereby depleting the secondary reservoir, causing reduced ability for modulating the service emergency brakes increasing the risk of a crash.
Remedy
Dealers will replace the bendix MV-3 dash control valves free of charge. the recall began on may 9, 2008. owners may contact international at 1-800-448-7825.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10253979This document is to guide users to eliminate brake pedal rattle noise.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10240193Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10227455J1939 Data link source address information
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10209487Calculating pulses per mile (speedometer setting); only models equipped with International engines
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10204137J1939 Data Link Troubleshooting
- 10201758Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
- 10199915General wheel speed sensor troubleshooting
- 10198708Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- 10189743Suggested alignment target values when performing a vehicle axle alignment
- 10189741Frame Rail Straightness Inspection Procedure
- 10185108ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10. 2010-2012 MaxxForce DT/9/10, 2007-2009 MaxxForce V8, 2008-2009 MaxxForce 11/13 engines
- 10181960Cab Lean Concern
- 10179294Driveline Information Center and Troubleshooting Procedures
- 10179289Repair Procedures for Vehicles Struck by Lightning
- 10177096A/C Refrigerant and Oil Capacities
- 10173025Cleaning and Disinfecting Trucks and Buses
- 10172045J1939 Data Link Troubleshooting
- 10169879Key Codes and Key Cutting Information (Not for CV Series)
- 10169867Power Distribution Center (PDC) Replacement; 7000 (Workstar) Model Series with Allison or Manual Transmissions
- 10165643Oil Capacities; All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10163416Suspension Lean Diagnostics; All models
- 10162034J1939 Data Link Source Address Information
- 10160941Suggested alignment target values when performing a vehicle axle alignment
- 10156576Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
Every International 7000 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.