2007 International 7700
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › 7700 › 2007
These records cover every 2007 International 7700. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
3 recalls name the 2007 International 7700. Newest first.
On certain 6X4 or 6X6 trucks with air brakes or tractors with air brakes and equipped with bendix SR-7 spring brake modulating valves, the internal rubber check valve may leak causing a delay in the application of the spring brakes to park the vehicle after the operator pulls the dash valve button.
Risk and remedy
Risk
This could delay or failure in applying the parking brakes which could result in a vehicle roll away, increasing the risk of a crash.
Remedy
International IS working with bendix to repair these vehicles (please see 07e-037). bendix will install a check valve repair kit for the affected SR-7 spring brake modulating valve free of charge. the recall began on september 28, 2007. Owners may contact bendix at 440-329-9000 and international at 1-800-448-7825.
On certain trucks equipped with chalmers rear suspensions, the adjustable torque rod end castings may be brittle. a brittle rod end casting may fracture without warning, causing the vehicles' rear axles to become misaligned.
Risk and remedy
Risk
This misalignment can cause the vehicle to lose directional stability at speeds that may result in a vehicle crash.
Remedy
Dealers will inspect the vehicles to determine if they were manufactured with a suspect torque rod end. if a suspect torque rod end IS found, the entire torque rod will be replaced. the recall began on october 6, 2006. owners may contact international at 1-800-448-7825.
On certain trucks equipped with SR-7 bendix brake valves, the check valve inside the valve cavity may not properly set, causing internal air leakage. if the check valve does not properly seat, the resulting leakage can cause a delay in the application of the spring brakes to park the vehicle after operator pulls the dash valve button.
Risk and remedy
Risk
The delayed parking brake application can occur without warning, leading to unintended vehicle rollaway increasing the risk of a crash.
Remedy
Dealers will inspect the valves and replace it free of charge. the recall began on july 21, 2006. owners may contact international at 1-800-448-7825.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10240193Snap-On torque wrench requirement for all big bore engine connecting rod bolts; A26, MaxxForce 13, N13 engines
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10227455J1939 Data link source address information
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10209487Calculating pulses per mile (speedometer setting); only models equipped with International engines
- 10208432ECM Calibration for DPF Replacement; Applies to MaxxForce Engines
- 10208431J1939 Data Link Source Address Information
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10204137J1939 Data Link Troubleshooting
- 10201758Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
- 10199915General wheel speed sensor troubleshooting
- 10198708Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- 10189743Suggested alignment target values when performing a vehicle axle alignment
- 10189741Frame Rail Straightness Inspection Procedure
- 10185108ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10. 2010-2012 MaxxForce DT/9/10, 2007-2009 MaxxForce V8, 2008-2009 MaxxForce 11/13 engines
- 10181960Cab Lean Concern
- 10179296Codes 141, 142, and 621 in a 2-box ECM/IDM; only models with 2-box ECM/IDM from 2003-2007
- 10179294Driveline Information Center and Troubleshooting Procedures
- 10179289Repair Procedures for Vehicles Struck by Lightning
- 10177096A/C Refrigerant and Oil Capacities
- 10173025Cleaning and Disinfecting Trucks and Buses
- 10172045J1939 Data Link Troubleshooting
- 10169879Key Codes and Key Cutting Information (Not for CV Series)
- 10169867Power Distribution Center (PDC) Replacement; 7000 (Workstar) Model Series with Allison or Manual Transmissions
- 10165643Oil Capacities; All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10163416Suspension Lean Diagnostics; All models
- 10162034J1939 Data Link Source Address Information
Every International 7700 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.