2007 International 9400
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › International › 9400 › 2007
These records cover every 2007 International 9400. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
1 recall names the 2007 International 9400. Newest first.
On certain trucks equipped with caterpillar C10, C11, C12, C13, C15 or C16 engines, the positive battery cables that supply power from the batteries to the starter may rub against an electrical ground cable between the engine and the starter, an electrical ground cable between the frame rail and the starter, or the frame rail itself.
Risk and remedy
Risk
This rubbing may cause an electrical short or a fire which can result in property damage, personal injury or death.
Remedy
Dealers will inspect the battery cables to determine if any rubbing has occurred. new battery cables will be replaced as necessary. dealers will also reroute the battery cables between the starter and battery box using new brackets. the recall began on april 20, 2007. owners may contact international at 1-800-448-7825.
Owner complaints
2 complaints1 involved a fire
What owners report most
Latest complaints
- Service brakes, air
2007 international 9400. Unit #1 was eastbound on IR80 (the ohio turnpike). Unit #1 had a brake system issue that started a fire, blew out the tires, and engulfed the vehicle. *Ln according to the police report, the brakes were set and then release. It appeared the brakes became extremely hot and blew a tire. A second tire blew out and the fire increased. (Ohio traffic crash report # 10-0255-89)*jb
- Engine and engine cooling › Exhaust system › Manifold/header/muffler/tail pipe
2007 international 9400 exhaust stack came off and struck another vehicle. *kb (ohio traffic crash report)*jb
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010428This article addresses chassis lean conditions on all chassis. This does not include any diagnostics for body leans such as a cab lean. Keep in mind that a chassis lean may cause or accentuate a cab lean. Filling out the printable form and using the notes in blue will help you to determine the source of the lean and identify the action and parts required to correct the lean.
- 10251414Starter Diagnostics and warranty claim procedure; all engines EXCLUDING Cummins ISB engine with Allison transmission or PSI engine.
- 10251409Suggested alignment target values when performing a vehicle axle alignment.
- 10246231J1939 Data Link Source Address Information
- 10243610How to request a horsepower quote; all International and Cummins engines
- 10243596General Wheel Speed Sensor Troubleshooting
- 10243595Diagnosis of chassis wander complaints.
- 10241555J1939 Data Link Source Address Information
- 10241554J1939 Data Link Troubleshooting
- 10234000Starter diagnostics and warranty claim procedure for all engines and all chassis EXCLUDING vehicles equipped with PSI engines or Cummins ISB engine with Allison transmissions
- 10227455J1939 Data link source address information
- 10222490Pico Scope CCOS (Crankcase Separator Test)
- 10219330PicoScope Test One Channel RCT
- 10219325PicoScope Test Resistance and Ohmmeter
- 10219319PicoScope Test for Datalink (CAN) Health Shorts & opens
- 10219314PicoScope Test - Battery Loss of Charge - Parasitic Draw Test
- 10219307PicoScope Test 5V & 12V Intermittent Open and Short circuit diagnostics
- 10204139Power Steering Diagnostics Flow / Pressure Specifications For Power Steering Gears and Power Steering Pumps
- 10201758Engine Oil Capacities. All International electronic engines 1994 to present and Cummins ISB, ISM, or ISX engines
- 10199915General wheel speed sensor troubleshooting
- 10198708Aftertreatment Clamp Corrosion; Single Can Aftertreatment Systems
- 10189743Suggested alignment target values when performing a vehicle axle alignment
- 10189741Frame Rail Straightness Inspection Procedure
- 10185108ECM Calibration for DPF Replacement; only trucks and busses built with 2007- 2009 MaxxForce DT/9/10. 2010-2012 MaxxForce DT/9/10, 2007-2009 MaxxForce V8, 2008-2009 MaxxForce 11/13 engines
- 10181960Cab Lean Concern
- 10179294Driveline Information Center and Troubleshooting Procedures
- 10179289Repair Procedures for Vehicles Struck by Lightning
- 10177096A/C Refrigerant and Oil Capacities
- 10173025Cleaning and Disinfecting Trucks and Buses
- 10172045J1939 Data Link Troubleshooting
- 10169879Key Codes and Key Cutting Information (Not for CV Series)
- 10165643Oil Capacities; All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10163416Suspension Lean Diagnostics; All models
- 10160941Suggested alignment target values when performing a vehicle axle alignment
- 10156576Engine Emission Label Replacement, Certificate of Conformance and Clean Idle Sticker Addition Procedure
- 10156324Driveline Information Center and Troubleshooting Procedures
- 10156305Tool Instruction - BCM Programming Harness
- 10145721A/C Refrigerant and Oil Capacities
- 10145715Engine Oil Capacities All Electronic International Engines 1994 - Present. Cummins ISB, ISM & ISX
- 10145711Radio Diagnostics and Information
Every International 9400 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.