Mack Trucks, Inc. (Mack) is recalling certain model year 2011-2016 Mack MRU and LEU trucks manufactured June 25, 2010, to April 30, 2015, and 2015-2016 LR6 trucks manufactured from December 18, 2014 through March 6, 2015. Excessive engine crankcase pressures may cause the 90-degree elbow of the vent tube assembly to detach from the crankcase ventilation…
Risk and remedy
Risk
If engine oil comes into contact with a hot surface, there could be an increased risk of a fire.
Remedy
Cummins will notify owners on behalf of Mack, and Cummins service centers will administer the repairs which include securing the ends of the 90-degree elbow and reprogramming the electronic control module (ECM) with software that can adjust the engine output under misfire conditions to limit crankcase pressures. These repairs will be performed free of charge. The recall began on June 12, 2015. Owners may contact Mack customer service at 1-800-528-6586 or Cummins Inc. at 1-800-343-7357. Mack's number for this recall is SC0391.
Mack Trucks, Inc. (Mack) is recalling certain model year 2015 Mack LEU trucks manufactured March 31, 2014, to December 12, 2014. In the affected vehicles, a component of the door opening mechanism may be too short and as a result, the door may not be able to be opened by someone inside the truck.
Risk and remedy
Risk
If the door cannot be opened from the inside, egress from the vehicle could be hindered which would increase the risk of injury in the event of an emergency.
Remedy
Mack will notify owners, and dealers will replace the inner door latches, free of charge. The recall began March 27, 2015. Owners may contact Mack customer service at 1-800-528-6586. Mack's number for this recall is SC0388.
Mack Trucks, Inc. (Mack) is recalling certain model year 2015 and 2016 CXU and LEU trucks manufactured May 20, 2014, to March 24, 2015, equipped with certain Haldex Life Seal Type 30/30 Long Stroke Air Brake Actuators manufactured from January 9, 2014, through February 3, 2015. The affected actuators may have an incomplete attachment of the internal rubber…
Risk and remedy
Risk
If the diaphragm is not completely attached, there may be internal leakage from the service section past the diaphragm, potentially trapping air pressure in the parking brake section. This air pressure in turn, if not vented, may prevent full release of the actuator unit, and may induce brake drag and may result in overheated wheelend service brakes, increasing the risk of a fire.
Remedy
Mack will notify owners, and dealers will inspect the brake actuator and replace, as necessary, free of charge. The recall began March 20, 2015. Owners may contact Mack customer service at 1-610-709-2131. Mack's number for this recall is SC0387.
Mack Trucks Inc. (Mack) is recalling certain model year 2014-2015 CXU, 2010-2015 LEU, and 2011-2015 MRU vehicles manufactured with certain Cummins Westport Model ISL G and ISX12 G engines. Condensation in the intake manifold may freeze during cold weather conditions and interfere with the proper operation of the intake manifold pressure sensor.
Risk and remedy
Risk
The improper operation of the sensor could induce elevated exhaust temperatures or flames from the exhaust pipe, increasing the risk of a vehicle fire or burn injury to a person near the exhaust pipe.
Remedy
Cummins and Cummins Westport will notify owners, and authorized Cummins service facilities will upload a new ECM calibration, free of charge. The recall began on March 12, 2014. Customers may contact Mack at 1-336-393-2000 or Cummins Inc. at 1-800-343-7357. Mack's number for this recall is SC0377.
Mack Trucks, Inc. (Mack) is recalling certain model year 2010-2015 LEU vehicles manufactured May 14, 2009, through February 14, 2014, and equipped with a Cummins ISL engine. In the affected vehicles, the exhaust pipe may disconnect from the muffler/catalyst.
Risk and remedy
Risk
If the exhaust pipe separates from the muffler on a twin-steer configured vehicle where the vehicle is operated from the right side, the operator may be exposed to carbon monoxide levels which may cause personal injury.
Remedy
Mack will notify owners. The recall began on April 21, 2014. The recall is expected to begin in late April 2014. Owners may contact Mack Trucks at 1-336-393-2000. Mack's number for this recall is SC0376.
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
11010857Vehicles may present with oil leak coming from the clutch/flywheel housing and observation of burned clutch smell or clutch slipping. These symptoms can be mistaken as a crankshaft rear main seal leak, when the actual cause is the crankshaft adaptor O-ring.
11008366CBR: To correct the MID136 SID 66 FMI 7 fault code the latest Bendix VCP fi le will need to be downloaded.
11006925CBR: 11L, 13L, And 16L Engine Oil Analysis Specifications - US10 And Newer Emissions
11000831CBR: Vehicles built with an 11 liter engine may experience a complaint of excessive fuel in the oil. It is possible that the source of the fuel is the rear fuel galley plug in the cylinder head. A new and improved fuel galley plug has been developed to resolve this issue.
10253804CBR: Equipped With An Automated Manual Transmission Model D or F ( AMT-D, AMT-F, mDrive) Missing X1 Value In VDA And Default Settings Guidelines, ParameterP1AOB; Fault Code P1052-54, Error 40,Or Error 18 Encountered During Clutch Or Tran.
10251331CBR - Active "Set Park Brake" Message On Drivers Information Display (DID).
10251329CBR - Automated Manual Transmission ( AMT ) Flywheel Pilot Bearing Wear On Input Shaft.
10251328CBR - Driveline Noise, Suspension Ride Height Too High, Suspension Will Not Exhaust - Chassis Built 2016w01 And Newer.
10249553CBR: TGW Will Not Connect After SIM Card Replacement
10248108Emissions Campaign: Mack Trucks has determined that certain 2014 - 2018 commercial model year CXU, GU, LEU, LR, MRU Vehicles require a replacement Diesel Particulate Filter (DPF) along with updated software.
10246086TSB: Mack Trucks now offer an improved HD Inter-Axle Through Shaft for the CRD 125, 150, 180, and 200 family carriers. The new HD shaft went into production on January 23rd, 2023 for 2.54 - 3.50 axle ratios and April 1st, 2023 for 3.56 - 3.98 ratios. The new HD through shaft is an upgrade over the current standard shaft and can now be used as a replacement part instead of the standard shaft. The new HD shaft has a new design to increase strength, longevity and life over the standard shaft.