2019 Mercedes-Benz A 220
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › A 220 › 2019
These records cover every 2019 Mercedes-Benz A 220. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
14 recalls name the 2019 Mercedes-Benz A 220. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2020-2021 CLA, 2019-2022 A-Class, 2022-2023 C-Class, 2024 CLE, 2020-2026 GLA/GLB, and 2023-2024 GLC vehicles. Please refer to MBUSA's recall report for specific model information. The micro-switch in the driver's door lock may corrode and fail to detect an open door, preventing the electronic parking brake…
Risk and remedy
Risk
A vehicle rollaway increases the risk of a crash or injury.
Remedy
Dealers will replace the driver's door lock, free of charge. Owner notification letters are expected to be mailed September 18, 2026. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Owners may contact MBUSA customer service at 1-800-367-6372. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning July 31, 2026.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2020 A220, 2020 CLA250, GLB250, AMG A35, AMG CLA45, AMG CLA35, and 2021 GLA250 vehicles. The vehicles may not be equipped with an inspection gauge to check the wear of the rear brake pads. In addition, information for using this inspection gauge might not be included in the owner's manual. As such…
Risk and remedy
Risk
Driving with worn brake pads can reduce braking ability, increasing the risk of a crash.
Remedy
Dealers will install an inspection gauge and provide supplemental owner's manual information, free of charge. Owner notification letters were mailed on February 29, 2024. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2022 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, AMG GT-Class, C-Class, E-Class, S-Class, SL-Class, GLC-Class, CLS-Class, GLB-Class, and G-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. An error in the communication module's SIM card…
Risk and remedy
Risk
A disabled eCall system would prevent a vehicle occupant from contacting the emergency services call center in an emergency, potentially delaying emergency responders and increasing the risk of injury.
Remedy
The communication module software will be updated through an Over-the-Air (OTA) update or by a dealer, free of charge. Owner notification letters were mailed July 8, 2022. Owner notification letters will be mailed in phases, on July 8, 2022, May 17, 2024, July 29, 2024, and September 27, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's numbers are for this recall is 2022060005 and 2023110006.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2018-2021 CLA-Class, GLE/GLS-Class, A-Class, C-Class, E-Class, E-Class Coupe/Convertible, GLA/GLB-Class, GLC-Class, and CLS-Class vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The rearview camera may not display the rearview image due to a software error. As such…
Risk and remedy
Risk
An inoperable rearview camera display reduces the driver's rear view, increasing the risk of a crash.
Remedy
Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed July 15, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022060007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2021 AMG GLB35, 2019-2020 A220, and 2020 GLB250 vehicles. The integral carrier that supports the front axle may corrode, causing it to fail.
Risk and remedy
Risk
Front axle carrier failure may result in a loss of steering control, increasing the risk of a crash.
Remedy
Dealers will inspect and replace the integral carrier, as necessary, free of charge. Owner notification letters were mailed July 29, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2022070009.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 AMG G63, C300, E300, G550, AMG GT63, AMG GT53, 2019-2020 A220, GLA250, GLC300, 2016 C300, 2020 AMG A35, AMG C43, AMG C63, CLA250, E350, E450, GLB250, GLE450, GLS450, GLS580, S560, and SL550 vehicles equipped with a gasoline engine. During the manufacturing process, particles may have been trapped…
Risk and remedy
Risk
A fuel leak in the presence of an ignition source, such as hot engine or exhaust components, can increase the risk of a fire.
Remedy
Dealers will replace the fuel rail and fuel injectors, free of charge. Owner notification letters were mailed April 22, 2022. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for the recall is 2022030003.
Mercedes-Benz LLC (MBUSA) is recalling certain 2018-2020 C300, 2019-2020 A220, AMG C43, AMG C63, 2020 GLE580, GLB250, 2020-2021 GLE450, GLE350, 2021 AMG GLE63, and AMG GLE53 vehicles. The LED headlights may have been incorrectly adjusted during a vehicle repair. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety…
Risk and remedy
Risk
Incorrectly adjusted headlights may reduce visibility, increasing the risk of a crash.
Remedy
Dealers will replace the LED headlights, free of charge. Interim letters notifying owners of the safety risk were mailed August 13, 2021. A second notice will be sent once the remedy is available. Owner notification letters were mailed January 2022. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019-2021 CLA-Class, GLE/GLS-Class, A-Class, E-Class, E-Class Coupe and Convertible, GLA/GLB-Class, GLC-Class, CLS-Class, and AMG GT-Class 4-door Coupe vehicles. Please refer to MBUSA's recall report for specific vehicle model details. The MBUX multimedia system software may cause the display to remain…
Risk and remedy
Risk
A backup camera that displays a blank image reduces the driver's rear view, increasing the risk of a crash or injury.
Remedy
The multimedia system software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed beginning June 28, 2021. Owners may contact MBUSA customer service at 1-800-367-6373. MBUSA's number for this recall is 2021050012.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2019 A220 vehicles. Certain labels containing important information such as tire pressure may not have been installed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Risk and remedy
Risk
If the tires are inflated to an incorrect tire pressure, the tires may be overloaded, and increase the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the vehicle for the labels and apply them, as necessary, free of charge. The recall began March 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020019.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 vehicles. The air conditioning condensation drain hose may not be installed properly. This may allow water to enter the driver and passenger foot wells and the center tunnel area, potentially damaging certain electrical components.
Risk and remedy
Risk
Water entering electrical components, can result in malfunctions of the supplemental restraint system (SRS), failure to start, activation of the limp-home mode while driving, and an impairment of other features, increasing the risk of injury or crash.
Remedy
MBUSA will notify owners, and dealers will inspect the air conditioning drain hose installation, correcting it if necessary, free of charge. The recall began August 31, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020070013.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 and A220 4MATIC vehicles. In certain operating conditions, the rearview camera software may cause a delay in displaying the rearview camera image. As such, these vehicles fail to comply to Federal Motor Safety Standard (FMVSS) number 111, "Rearview Mirrors."
Risk and remedy
Risk
A delayed rearview camera display can reduce the driver's view of what is behind the car, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will update the rearview camera software, free of charge. The recall began April 8, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020030018.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019-2020 A 220 and A 220 4MATIC, 2020 CLA 250, CLA 250 4 MATIC, GLC 300 Coupe 4MATIC, GLC 300 and GLC 300 4MATIC vehicles. The driver's side front airbag modules may not have been properly bolted down.
Risk and remedy
Risk
In the event of a crash necessitating deployment of the driver's front airbag, the airbag may not deploy properly, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the driver airbag module and replace it, as necessary, free of charge. The recall began October 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019100001.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2019 A220 and A220 4MATIC vehicles. Due to improper welding, the pedal plate may bend, impairing the operation of the brake pedal.
Risk and remedy
Risk
Impaired operation of the brake pedal may increase the risk of crash.
Remedy
MBUSA will notify owners, and dealers will inspect the welding of the brake pedal, replacing it as necessary, free of charge. The recall began May 31, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019050002.
Owner complaints
48 complaints
What owners report most
Latest complaints
- Engine
I am filing a vehicle safety complaint regarding my 2019 Mercedes-Benz A220 equipped with the M260 engine. While driving on a public street, my vehicle experienced an unexpected loss of engine power and stalling. The engine also exhibited significant shaking, misfiring, and activation of the…
I am filing a vehicle safety complaint regarding my 2019 Mercedes-Benz A220 equipped with the M260 engine. While driving on a public street, my vehicle experienced an unexpected loss of engine power and stalling. The engine also exhibited significant shaking, misfiring, and activation of the check-engine warning light. The unexpected loss of power while driving created a dangerous situation because I could have been involved in a collision with another vehicle. I was extremely concerned for my safety and the safety of other motorists. My mechanic subsequently diagnosed the vehicle with a cylinder head failure and advised me that continuing to drive could be dangerous. Because of the seriousness of the mechanical problem and the safety risks involved, I had the vehicle repaired. The repair cost approximately $3,800 and was performed by an independent mechanic using genuine Mercedes-Benz parts purchased from an authorized Mercedes-Benz dealership. I later learned that Mercedes-Benz had reportedly extended warranty coverage for certain M260 engine cylinder head failures to 15 years or 150,000 miles. I am concerned that other Mercedes-Benz vehicles equipped with the same engine could experience similar failures, potentially resulting in unexpected engine stalling or loss of power while driving. I respectfully request that NHTSA investigate whether this cylinder head failure represents a broader vehicle safety defect that could endanger drivers, passengers, and other motorists.
- Unknown or other
This recall has not been made available in a timely manner, which has resulted in the inability to register my car
- Latches/locks/linkages
The contact owns a 2019 Mercedes-Benz A-220. The contact received notification of NHTSA Campaign Number: 26V481000 (Latches/Locks/Linkages). The dealer was contacted and confirmed that the part to do the recall repair was on back order.
- Latches/locks/linkages
The contact owns a 2019 Mercedes-Benz A220. The contact stated that while the vehicle was parked, the front driver's door failed to latch as intended. The dealer was notified of the failure, but no assistance was provided. The vehicle was not diagnosed or repaired. The contact received notification…
The contact owns a 2019 Mercedes-Benz A220. The contact stated that while the vehicle was parked, the front driver's door failed to latch as intended. The dealer was notified of the failure, but no assistance was provided. The vehicle was not diagnosed or repaired. The contact received notification of NHTSA Campaign Number: 26V481000 (Latches/Locks/Linkages); however, the part to perform the recall repair was not yet available. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 77,000.
- Unknown or other
I was driving home from work down the hwy, when the sun visor shade fell down and hit me in the head and covered my face, temporarily blinding me, like a blanket was pulled over my face. It's very difficult to see the road or other drivers when you are blinded at 70mph! Car only had 15,500 miles on it...
- Engine
Thermostat failed making car over heat also sunroof failed due to cheap rolling up shade device getting stuck , when car was less than 4 years old with very little use.
- Engine · Forward collision avoidance › Automatic emergency braking · Service brakes
Vehicle: 2019 Mercedes-Benz A220 VIN: [XXX] Dealer: Mercedes-Benz of Walnut Creek (Walnut Creek, CA) I am reporting multiple safety defects involving federally regulated systems. The vehicle has repeatedly activated emergency braking at freeway speeds without reason, posing a significant risk of…
Vehicle: 2019 Mercedes-Benz A220 VIN: [XXX] Dealer: Mercedes-Benz of Walnut Creek (Walnut Creek, CA) I am reporting multiple safety defects involving federally regulated systems. The vehicle has repeatedly activated emergency braking at freeway speeds without reason, posing a significant risk of collision. The brake assist warning appears frequently, and both the front and rear proximity/collision sensors display a full red warning state with continuous audible alerts. These alerts cannot be cleared without manually disabling the safety system each time the vehicle is started. One of the sensors physically detached from the vehicle. Backup and parking assist features do not function correctly, and the vehicle repeatedly shows malfunction warnings. The dealer verbally stated that a “manufacturer-covered engine repair” was needed, but would not disclose the nature of the repair or whether it relates to these safety issues. After two weeks in their possession, the dealer refused to provide written documentation of any diagnostics or repairs performed. They attempted to return the vehicle without confirming whether it is safe to operate and threatened storage fees when I requested written confirmation. These issues involve systems covered under FMVSS 101, 111, 126, and 135, including electronic stability control, braking, rear visibility, and driver-interface warnings. The failures pose a clear safety risk to the driver and other motorists. I am requesting NHTSA review these defects for potential investigation or recall. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
- Air bags
Srs light on Mercedes told me no recalls
- Fuel/propulsion system
While driving the car shuts off and unable to restart. It will turn over but not remain started enough to move the vehicle. I did notice it jerk when speed was increased a few times before. Fuel pump was replaced less than a year ago according to Mercedes in Tuscaloosa Alabama. . After a certified…
While driving the car shuts off and unable to restart. It will turn over but not remain started enough to move the vehicle. I did notice it jerk when speed was increased a few times before. Fuel pump was replaced less than a year ago according to Mercedes in Tuscaloosa Alabama. . After a certified Mercedes mechanic inspected the vehicle I was told it was the fuel pump once again. $4000+ later and I am having the same issue. Very frustrating to be stranded with my kids in the car.
- Electrical system · Engine · Unknown or other
I have had numerous issues with my 2019 A220. At 92k mi my cylinder head had to be replaced. My check engine light came on and they said there was a cylinder head leak. At 108k miles I had to have it replaced yet again because my car lost power driving uphill when shifting between 4th and 5th gear.…
I have had numerous issues with my 2019 A220. At 92k mi my cylinder head had to be replaced. My check engine light came on and they said there was a cylinder head leak. At 108k miles I had to have it replaced yet again because my car lost power driving uphill when shifting between 4th and 5th gear. Now at 112k mi the check engine light came on and sure enough they need to replace all 4 ignition coils… Additionally, I have issues with my air vents. They will frequently send air out of a section I have turned off (ex. turn air on my upper body and it sends air to my feet instead). Somewhat related but whenever I turn my car off it makes a lot of strange noises on the inside of the car by my entertainment center, almost similar to a stomach grumbling/farting noises. Lastly, I’ve had issues with trying to close my windows and they’ll close fully but then drop down half an inch or so afterward.
- Unknown or other
The tow hook and strap used when necessary to tow a car and that is stowed under the car or behind the rear bumper and accessed through a small door on the bumper spontaneously deployed while I was driving. It flew up against the side of the car, causing minor damage, damaged and partially…
The tow hook and strap used when necessary to tow a car and that is stowed under the car or behind the rear bumper and accessed through a small door on the bumper spontaneously deployed while I was driving. It flew up against the side of the car, causing minor damage, damaged and partially dislodged the rear bumper, and the hook embedded in the right rear tire, causing it to go flat. I am waiting to learn whether there is additional damage to the underside of the car such as to a brake line. The parts are available for inspection. This is not a problem to be reproduced! I have photos showing the car and the hook in my tire. The only warning light appeared after the tire started losing pressure, but the thump sound as the hook and strap hit my car, and as the tire rotated and drove over the hook alerted me first. The weather was clear, there was no immediate traffic, no obstacles in the road. No sign of a bullet or something to cause it to deploy.
- Unknown or other
The sun roof not working since 2023 The roller shade needs to be replaced very BAD design . I took to the dealer to diagnose the problem cost me $200.0 to diagnose no money back I thought it was an electronic issue not because used very cheap rolling shades very under used accessories. Yes I can drive the car paid probably $4,000 for sunroof does not work.
- Fuel system, gasoline
The contact owns a 2019 Mercedes-Benz A220. The contact stated that while driving at an undisclosed speed, the vehicle briefly began to shake and vibrate violently, after which there was an abnormal odor inside the vehicle. The vehicle returned to normal functionality, but the failure became a…
The contact owns a 2019 Mercedes-Benz A220. The contact stated that while driving at an undisclosed speed, the vehicle briefly began to shake and vibrate violently, after which there was an abnormal odor inside the vehicle. The vehicle returned to normal functionality, but the failure became a regular occurrence. The check engine warning light was illuminated. The vehicle was taken to an independent mechanic, who diagnosed failures with the fuel injectors and the crankcase ventilation system. The contact was provided the following OBD codes; P1CEF85 and P1CE577. The vehicle was not repaired. After investigating the failure, the contact related the failure to NHTSA Campaign Number: 21V961000 (Fuel System, Gasoline); but the VIN was not included. The manufacturer was notified of the failure but provided no assistance. The failure mileage was 59,000.
- Fuel/propulsion system
The car shakes, vibrates and has rough idling. My engines stalls when it is at low rpm. I am afraid that if this is not fixed a fuel leak could occur in the presence of an ignition source, such as hot engine or exhaust components, which could increase the risk of a fire
- Fuel/propulsion system
The car shakes, vibrates and has rough idling. My engines stalls when it is at low rpm. I am afraid that if this is not fixed a fuel leak could occur in the presence of an ignition source, such as hot engine or exhaust components, which could increase the risk of a fire
- Electrical system
My screens have gone black and will no longer turn on. I cannot see how much gas I have or how fast I am driving.
- Back over prevention › Sensing system › Camera · Electrical system · Visibility › Defroster/defogger/hvac system
The component or system that failed was the MBUX Hard Disk Drive (Part#: A0009062711). My car is available for inspection upon request. My safety and the safety of others were put at risk because when the MBUX Hard Disk Drive malfunctioned the following happened: 1) The defogger was spontaneously…
The component or system that failed was the MBUX Hard Disk Drive (Part#: A0009062711). My car is available for inspection upon request. My safety and the safety of others were put at risk because when the MBUX Hard Disk Drive malfunctioned the following happened: 1) The defogger was spontaneously disabled hindering the driver's view of the road 2) The rear camera was spontaneously disabled while in active use of reversing the car risking hitting someone or something 3) Content from Satellite radio some of which was vulgar language would spontaneously blast through the car speaker on the highest volume causing the driver to become alarmed/distracted from the road with the inability to power off, mute or lower the volume because the volume, mute and power off button for the radio would malfunction. This incident caused me to slighty loose control of wheel because I was caught by suprise or shock of loud music or content coming through the speaker uninvited. Lastly, in the year 2021 a recall/remedy for this component was to be replaced by Mercedes Benz on other specific models. I do not understand why my vehicle was not added to the list of cars that required a remedy. I should NOT had to learn and experience similar impairments 3 years after a known issue. I should had been made aware of this defective part 3 years ago.
- Engine
Unknown vehicle won’t go pass 20mph in first and second gear when in third gear it goes passes 20mph
- Electrical system · Unknown or other
The moonroof is not working properly the shade part gets stuck and won’t open completely it gets to certain point and stop and shade part bunches up. I have noticed all lot of owners online with this same A220 2019 make and model and year are having the same issues. I taken it Mercedes and was told it’s no longer under warranty and that it would cost me $265 just if diagnosed.
- Unknown or other
While turning on my Rear defrost to defrost my windshield I heard a explosion then my rear windshield started crackling and shattering all over. I then turned the rear defrost off. Got out to see my whole windshield has shattered from each edge corner spreading from top to bottom. But I don't smell anything burning it sounded like something had blown out but it was extremely loud.
- Electrical system
On 03/10/23, I contacted the Mercedes-Benz service department regarding the black screen on the driver's side display. The Mercedes-Benz service personnel informed me that the screen needed to be replaced, with an estimated cost of around $2000. I agreed to their suggestion and authorized the…
On 03/10/23, I contacted the Mercedes-Benz service department regarding the black screen on the driver's side display. The Mercedes-Benz service personnel informed me that the screen needed to be replaced, with an estimated cost of around $2000. I agreed to their suggestion and authorized the replacement. Later, the Mercedes-Benz service personnel contacted me again, stating that the black screen issue was not resolved and recommended replacing the computer mainframe, which would cost over $6500. I refused their suggestion as the cost exceeded what I was willing to pay. When I went to pick up my car from the Mercedes-Benz dealership, I noticed that the central control display screen was also blacked out. I confronted them about it, and they admitted that they were responsible for the damage. However, they stated that they were not liable for compensation because I did not pay the initial $2000 for the replacement of the screen. My argument is that I was willing to pay for the replacement, but they failed to fix the screen. Why should I be held responsible for the payment? Additionally, they did not even replace the screen, so why should they use the excuse of the unpaid replacement cost to avoid compensating me for the damage they caused to my central control display? It is unfair to expect a fair exchange when they neither replaced the screen nor fixed it. I feel that this situation is an act of consumer mistreatment.
- Electrical system
The display screen of the driver's seat was damaged due to the automatic update last month. The dealer told me to replace the display screen for US$2,000. After I agreed to pay, I was told that the central control display screen was broken again and needed to be replaced for nearly US$7,000. I…
The display screen of the driver's seat was damaged due to the automatic update last month. The dealer told me to replace the display screen for US$2,000. After I agreed to pay, I was told that the central control display screen was broken again and needed to be replaced for nearly US$7,000. I refused the dealer. However, the central control display screen was still good originally. Now the main driver does not have a display screen, and even the central control screen is damaged. The central control screen is damaged due to their operation. How should I protect my rights in this situation?
- Visibility › Sun/moon roof assembly
The contact owns a 2019 Mercedes-Benz A220. The contact stated while driving approximately 30 MPH, there was a loud banging sound coming from the roof of the vehicle. The contact stated that after stopping to inspect the vehicle it was discovered that the glass sunroof had shattered. The contact…
The contact owns a 2019 Mercedes-Benz A220. The contact stated while driving approximately 30 MPH, there was a loud banging sound coming from the roof of the vehicle. The contact stated that after stopping to inspect the vehicle it was discovered that the glass sunroof had shattered. The contact stated that there was no impact to glass sunroof to cause the glass sunroof to shatter. The cause of the failure was not yet determined. The local dealer and manufacturer were not notified of the failure. The failure mileage was approximately 28,000.
- Engine
The contact owns a 2019 Mercedes-Benz A220. The contact stated that the engine check warning light was illuminated. The vehicle was taken to the dealer and PCV and purge valve and other unknown valves were replaced but the failure persisted. The vehicle was taken back to the dealer and a software…
The contact owns a 2019 Mercedes-Benz A220. The contact stated that the engine check warning light was illuminated. The vehicle was taken to the dealer and PCV and purge valve and other unknown valves were replaced but the failure persisted. The vehicle was taken back to the dealer and a software updated was performed; however, the failure reoccurred. The vehicle was taken to the dealer and the contact was informed that the vehicle needed another software update. The vehicle was not repaired. The manufacturer was not contacted. The approximate failure mileage was 25,000.
- Fuel system, gasoline
The contact owns a 2019 Mercedes-Benz A220. The contact stated that upon attempting to refuel the vehicle, the gas cap failed to open. The vehicle was towed to the dealer, where the fuel door intermediate lid was opened, and the contact returned to the gas station to refuel the vehicle; however…
The contact owns a 2019 Mercedes-Benz A220. The contact stated that upon attempting to refuel the vehicle, the gas cap failed to open. The vehicle was towed to the dealer, where the fuel door intermediate lid was opened, and the contact returned to the gas station to refuel the vehicle; however, the failure recurred. The vehicle was taken to the dealer, where it was diagnosed that the fuel door release motor needed to be replaced. The vehicle was repaired. The manufacturer was notified of the failure, but no assistance was provided. The failure mileage was approximately 10,000.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010438Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 01.06.2023 (Send to Body/Chassis/Entertainment Inbox) - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 01.06.2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009549Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. Cause This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Remedy Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case for vehicles from production date 6/1/2023 - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] - Add alarm history of anti-theft alarm system [N26/6], alarm siren [H3/1] and front signal acquisition and actuation module [N10/6] 3. Remedy for vehicles prior to production date 6/1/2023 - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008712Complaint Check engine light on. One of the below fault codes is current in the engine control module (N3/10). P04DB29, P04DB31, P04DB79 Cause Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for the relevant vent line contact switch noted below. Refer to attached photos of connection locations. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found. The circuit from ME provides 5V and is pulled to 0V when the ground connection is intact. M260 P04DB31- S88/15 P04DB79- S88/16 M264 P04DB31- S88/15 P04DB79- S88/16 P04DB29- S88/17 M270/M274 P04DB79- S88/5 Note: This repair is not warrantable if the connection was left loose during previous repair/maintenance.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008093Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008056Complaint Check engine light on. Fault code P207273 - "Throttle actuator valve is blocked due to ice" stored. Engine may crank and not start. Fault code P210185 may also be stored. Cause Moisture freezing on throttle actuator during extreme low ambient temperatures. Remedy Update software of engine control module. Software increases throttle valve flapping after engine turned off to prevent moisture buildup.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007972Complaint After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Cause Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation.
- 11007796Complaint Individual functions such as sliding sunroof or roller sunblind can no longer be operated using the gesture recognition system. Cause Gesture recognition system control unit software N168 Remedy For vehicles before modification year 23/2: A remedy is currently being developed. Replacing parts will have no effect. For vehicles as of modification year 23/2: Considered to be a series production configuration. A change will not be possible in future.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11006700Complaint Once the head unit A26/17 is updated to the FUP4 software release E445.0, it may be the case that online connectivity is no longer available Cause E445.0 FUP4 software release Remedy Update the A26/17 - MBUX multimedia system (Head unit) software to E445.2 FUP4 Optimized or newer version to resolve the complaint.
- 11005313Complaint Check engine light on and fault code P019185 current or stored in MED41 control unit. Adaptation and misfire faults may also be stored. Vehicle may enter limp home mode. Cause False detection of rail pressure sensor out of range. Remedy Update software of engine control module N3/10. Reset mixture adaptation and clear fault codes.
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11005292Complaint Vibrations in steering at speeds lower than 50 km/h when turning left and right or while at a stop. May be perceived as a noise from the transmission. Cause Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Remedy Software A 247 902 11 16 available in Xentry with latest add-ons.
- 11005288Complaint Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Cause Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, 247476 247747, 247646 247647 the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, 247751 247753, 274651 the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part.
- 11005284Complaint Check engine light is illuminated Fault code stored in MED41 control unit- P013300 Oxygen sensor 1 has a delayed reaction. Cause MED41 software Remedy Perform software update of MED41 control unit.
- 11000596Instrument cluster message "4MATIC inoperative". The following fault code may be present in all-wheel drive control unit N15/17: P147354 - Erroneous adaptation of the transfer case. The calibration is missing. P14759A - The coupling of the transfer case has malfunctioned. The operating conditions for the component or the system have not been fulfilled. Coupling of the rear axle differential has reached the wear limit or a coupling defect is present. Remedy Please read off the installed part number of the rear axle differential. For model designations (flat model series and not AMG 35 variants) 118345; 118347; 118613; 118615; 118647; 177013; 177015; 177045; 177047; 177145; 177147; 177188; 177945; 247013; 247045; 247047, the following applies: If part number A2473502702 is not installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If part number A2473502702 is installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced. For model designations (high model series and AMG 35 variants) 177151; 177051; 118351; 118651; 177951, the following applies: If one of the part numbers A2473502702; A2473502503; A2473504504 has not been installed, the coupling package can be replaced. To this end, a repair kit has been added as a replacement part. If one of the part numbers A2473502702; A2473502503; A2473504504 has been installed, the installation of the coupling package repair kit is not permissible and the rear axle differential should be replaced.
- 11000546Vibrations in steering at speeds lower than 50 km/h, possible when turning both in and back, also partly noticeable after changing to winter tires. Controller instability of steering software, caused by reduced friction in steering (tolerance for production + running-in characteristics). Software A 247 902 11 16 available in Xentry with latest add-ons.
- 10253715Check engine light active and FC P146364 Temp. and pressure sensor B4/7 is stored in Engine control unit and Fuel pump control unit. Software parameter in Fuel pump control unit. Perform software update for Fuel System Control Module (FSCM) N118. New software is A0009026661.
- 10253708In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2019 - 2021 A/CLA/ GLA/GLB/ GLE and GLS-Class vehicles, the FSCM software for the fuel pressure sensor and temperature plausibility checks may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ('MIL') might illuminate. Any repair: under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. We hope you are enjoying your Mercedes-Benz vehicle and we apologize for any inconvenience this may have caused.
- 10253706IMPORTANT EMISSION EXTENDED WARRANTY INFORMATION In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC ("MBUSA") is extending the warranty coverage on the Fuel System Control Module (FSCM) software in certain Model Year ("MY") vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first) due to the following condition: Under certain circumstances, the FSCM software for the fuel pressure sensor and fuel temperature plausibility check may not meet specifications. As a result, the check engine Malfunction Indicator Lamp ("MIL") might illuminate. Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information and may be audited. P146264 The sensor Low fuel pressure and fuel temperature has a malfunction. There is an implausible signal. -and/or- P146364 This error code can be ignored and erased. 'OR' Sensor Low fuel pressure and fuel temperature has a malfunction during calculation of the fuel pressure. There is an implausible signal. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 47045 90 Control Unit, Fuel Pump - Software Parts (Software): A0009026661 Please note that damage incurred from abuse, accidents, vandalism or other non-warrantable causes that are not covered by the New Vehicle Limited Warranty are similarly not covered by this Extended Warranty. No part replacement is covered by this extended warranty.
- 10253703This is to notify you of the Service Campaign OTA update for the MBUX system software in 750,313 Model Year (MY) MY19-24 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles. The vehicles will not be visible or flagged in VMI or EVA. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-24 A-Class, C-Class, CLA, CLS, E-Class, EQB, GLA, GLC, GLE, GLS, GT 4-door (177, 118, 257, 213, 238, 243, 247, 253, 167, 290 platform) vehicles, the MBUX system software does not correspond with the latest series production configuration. The MBUX system will receive an OTA update that includes general product improvements and robustness enhancements for the Line Traffic Information and Point of Interest (POI) features. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer's vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10252777Tailgate opens unintentionally. Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. The recoding can be carried out as follows: 1. Add AO code O19 in VeDoc (O as in the letter "O" for Oscar, not the number "0"/zero) 2. EZS N73: Perform SCN coding 3. Deactivate the vehicle key (a successful deactivation is indicated by the LED lighting up 2x briefly and then 1x for a long period). 4. Place the vehicle key on the key symbol in the storage compartment and then switch on the ignition. All other vehicle keys must be outside of the vehicle when doing this! Perform steps 3 and 4 successively for all vehicle keys. Notes: 6th, 7th and 8th generation keys can be deactivated as follows: Up to modification year 22/1, by double-clicking on the locking button
- 10251356The radio station favorites list is no longer present after bus idle Saving process during download Perform software update in control unit HU6 in the head unit (A26/17) to version E871.1 (A 247 904 53 00).
- 10251118After clicking on the "Radio" selection function, the radio does not start and instead a permanent loading wheel is displayed. See attached picture for example. Software version Remedy A26/17 - MBUX multimedia system (Head unit) unit must be replaced. When the head unit is in this condition, a software update will not remedy the situation. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 10249540Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an OTA update to improve system stability and availability of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. A letter will be mailed to all customers informing them of this OTA software update.
- 10249537Complaint Customer complains about anti-theft alarm system triggering without obvious cause when the vehicle is parked and/or when entering the vehicle. All MFA2 and 167 derivates with code 882 may be affected. This is caused by a sporadic loss of communication to the anti-theft alarm system [N26/6]. In many instances there are one or more FCs U110D87, U001988, U016787 stored in the control units anti-theft alarm system [N26/6] and/or signal acquisition and actuation module [N10] / [N10/6]. The alarm system memory may contain several alarm sources. Please process all following points in succession: 1. Check - Power supply of the overhead control panel [N70] - Ground points of the overhead control panel [N70] Model series 118, 177, 247: W78 Model series 167: W15/2 Model series 243: W78/2 - LIN lines between overhead control panel [N70] and alarm siren [H3/1] - CAN lines between overhead control panel [N70] and signal acquisition and actuation module [N10] or [N10/6] 2. Open TIPS case - Open a TIPS case for vehicles: As of manufacturing date 01.02.2022, except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa As of manufacturing date 01.08.2022 and production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa - Attach photo of overhead control panel label (see example images) - Add control unit log of anti-theft alarm system [N26/6] 3. Remedy for vehicles prior to manufacturing date 01.02.2022 (except production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) or 01.08.2022 (production plant 4831 Aguascalientes Mexico or 1380 Tuscaloosa) - If the problem cannot be reproduced, the overhead control panel [N70] (anti-theft alarm system [N26/6] is integrated) must be replaced.
- 10249495Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel, re-align the MRSM/SCCM, and re-fasten the screws (see WIS). Sometimes there is stress at the MRSM/SCCM and noises occur. - If noises continue to occur, swap the MRSM/SCCM into a vehicle without any (noise) complaints. - If the noises occur with the MRSM/SCCM complained about when it is in the vehicle without a complaint (donor vehicle), the MRSM/SCCM can be replaced. - If noises also occur in the customer vehicle with the MRSM/SCCM from the reference vehicle, the MRSM/SCCM is not the cause and must not be replaced. Notes: - When installing the MRSM/SCCM, make sure that no damage occurs! - Only disassemble and mount all component parts in the "straight-ahead position" (see also WIS). - Please refer to this LI in the "Notes" section of the warranty claim!
- 10249482The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for the damaged part analysis: 1. Grinding noise | pot. cause: steering wheel | see attachment: Lenkrad-Schleifgerusch_SteeringWheel-GrindingNoises. mp4 2. Creaking/cracking noise | pot. cause: steering column switch module | see attachment: MRSM-Schleifgerusch_ SCCM-GrindingNoises.MOV If the noise is due to the steering column switch module, please use LI46.10-P-077314. Check for grinding areas on the steering wheel: Please check the covers on the rear for protrusion and, if necessary, remount. 1. Mask off openings on back of steering wheel with adhesive tape 1. Mark the back of the steering wheel with colored chalk (see Picture 1) 2. Mount steering wheel on steering column switch module and turn the steering wheel from left lock to right lock ten times. 3. The chalk will now have disappeared in the areas where there is rubbing (see Picture 2) Warning: Ensure that no cables and visible areas of the steering wheel are damaged. The abrasive excess material on the back of the steering wheel must be carefully removed with a Dremel tool. Tip: You will need to remove approx. 0.1 mm to 0.3 mm of material (example: Picture 3) Make sure that none of the ground-off material gets into the steering wheel. After removing the material, clean the entire back of the steering wheel with a 1% soap solution.
- 10248203Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service for the navigation system. Additional product improvements including infotainment system robustness will be implemented. The software update will be downloaded in the background. The subsequent installation takes roughly 45 minutes and requires the customer's consent in the vehicle. During installation, the system can be used without restriction. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248195Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge and do not require a dealer visit. No customer letter will be mailed for this OTA software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10241534In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA, LLC (MBUSA) is extending the warranty coverage on the exhaust valve system in certain Model Year (MY) vehicles listed below from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 15 years/150,000 miles (whichever occurs first). This extended warranty applies to the condition described below that may necessitate the repair or replacement of components related to the exhaust valve assembly (e.g. exhaust valve, cylinder head). The valve guide and/or seat ring may wear over time due to increased lateral forces during operation. This could potentially cause combustion misfire for cylinder 1 through 4, resulting in an activation of the check engine Malfunction Indicator Lamp (MIL). Please be advised that all repairs being claimed under this extended warranty must have a Quick Test uploaded with the following fault code information, and may be audited. P030085 Combustion misfire has been detected P030x85 Cylinder x misfire detected. (x = the affected cylinder) P1CEF85 - Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at atleast one cylinder. P1CE577 - Injector injection quantity adjustment for uniform mixture formation has detected an excessively lean mixture at atleast one cylinder. All repairs found to be functioning properly or without proper documentation will be returned and the claim debited in full. Only the following damage codes and parts may be claimed for the aforementioned repairs: Damage Codes: 01201 Cylinder Head 05202 Exhaust Valve 01205 Valve seat ring exhaust valve 01206 Valve Guide Exhaust Valve
Every Mercedes-Benz A 220 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.