2017 Mercedes-Benz AMG C43
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › AMG C43 › 2017
These records cover every 2017 Mercedes-Benz AMG C43. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
10 recalls name the 2017 Mercedes-Benz AMG C43. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 - 2021 CLA-Class, GLA-Class, GLE-Class, GLS-Class, SLC-Class, A-Class, GT-Class, C-Class, E-Class, S-Class, CLS-Class, SL-Class, B-Class, GLB-Class, GLC-Class, and G-Class vehicles. Please refer to the Part 573 report for specific vehicle model details. The software design of the communication…
Risk and remedy
Risk
Failure of the eCall system may result in emergency responders being dispatched to the wrong location, increasing the risk of injury following a crash.
Remedy
MBUSA will notify owners, and the communication module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. The recall began March 12, 2021. Owners may contact MBUSA customer service at 1-877-762-8267. MBUSA's number for this recall is 2021020025.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2021 C300, 2017-2020 AMG C43, and AMG C63 vehicles. The front seat belts might not fully retract to their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection."
Risk and remedy
Risk
If the seat belt does not fully retract, the occupant may find the operation of the seat belt inconvenient and not wear it, increasing the risk of injury in the event of a crash.
Remedy
MBUSA will notify owners, and dealers will check the retraction function of the front seat belts and adjust the damping foam within the B-pillars, as necessary, free of charge. The recall began February 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2021020010.
Mercedes-Benz USA, LLC (Mercedes) is recalling certain 2017-2018 Mercedes-Benz C300 Cabriolet, C300 Coupe, AMG C43 Coupe, C300 4MATIC Cabriolet, C300 4MATIC Coupe, AMG C43 Cabriolet, AMG C63 Cabriolet, AMG C63 Coupe, AMG C63 S Cabriolet and AMG C63 S Coupe vehicles and 2018 Mercedes-Benz E400 Coupe, E400 Cabriolet, E400 4MATIC Cabriolet and E400 4MATIC…
Risk and remedy
Risk
If the seatback does not properly lock, in the event of a crash, the seatbacks may fold forward, increasing the risk of injury.
Remedy
Mercedes will notify owners, and dealers will inspect the locking of the seatback on the affected vehicles and replace the seatback lock, as necessary, free of charge. An interim owner letter was mailed on April 12, 2019 to notify owners. Owners will receive a second notification when the remedy is available. Owners may contact Mercedes-Benz customer service at 1-800-367-6372. MBUSA's number for this recall is 2019040007.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 Mercedes C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63S AMG Cabriolet, and C63 AMG Cabriolet vehicles. Due to a bonding issue introduced in the production process, the rear beltline trim may separate from the vehicle.
Risk and remedy
Risk
If the beltline trim were to separate from the vehicle while driving, it could become a road hazard, increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will inspect the rear beltline trim and replace the trim if necessary, free of charge. The recall began on September 21, 2018. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2018 C43 AMG 4Matic Coupe, C300 Coupe, C300 4Matic Coupe, C300 4Matic Cabriolet, C300 Cabriolet, C43 AMG 4Matic Cabriolet and C63S AMG Cabriolet, 2017 C63 AMG Cabriolet, C63S AMG Coupe and C63 AMG Coupe, 2018 E400 Coupe and E400 4Matic Coupe vehicles. The seatbacks of the front seats may not properly…
Risk and remedy
Risk
If the seatback does not properly lock, in the event of a crash, the seatbacks may fold forward, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will inspect the locking of the seatbacks, replacing the seatbacks lock, as necessary, free of charge. The recall is expected to begin May 25, 2018. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2018040007.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC. (MBUSA) is recalling one 2017 C43 AMG, one E300 4Matic sedan, one GLC300, and one E43 AMG 4Matic sedan. These vehicles have electrical power steering control units with improperly welded contact pins.
Risk and remedy
Risk
The improperly welded pins may lose contact, deactivating the power steering assist and increasing the risk of a crash.
Remedy
MBUSA will notify owners, and dealers will replace the electric power steering rack, free of charge. The recall is expected to begin November 10, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017 C300, C300 4Matic, C300 Coupe, C300 Coupe 4Matic, C43 AMG, C43 AMG Coupe, C43 AMG Cabrio, C63 AMG, C63 AMG Coupe, C63S AMG, C63S AMG Coupe, C63S Cabrio, GLC300, GLC300 4Matic, GLC43 AMG, S550, S550 4Matic, S550e, S600, S63 AMG 4Matic, S65, Mercedes-Maybach S550 4Matic, and Mercedes-Maybach S600…
Risk and remedy
Risk
If the front seat seatbelt pretensioners do not function properly, the seat occupants may not be adequately restrained in the event of a crash, increasing the risk of injury.
Remedy
MBUSA will notify owners, and dealers will replace the front seat belts, free of charge. The recall began October 13, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.
Owner complaints
23 complaints1 involved a crash
What owners report most
Latest complaints
- Seat belts
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that the front driver’s side seat belt failed to retract as intended. No warning light was illuminated. The vehicle was taken to a local dealer for diagnosis but was not repaired due to the cost. Upon further investigation, the…
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that the front driver’s side seat belt failed to retract as intended. No warning light was illuminated. The vehicle was taken to a local dealer for diagnosis but was not repaired due to the cost. Upon further investigation, the contact related the failure to NHTSA Campaign Number: 21V032000 (Seat Belt); however, the VIN was not included. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline for assistance. The failure mileage was approximately 70,000.
- Seat belts
Both front seat belts on the driver and passenger side fail to retract. Looking up my car model I found the following: Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2021 C300, 2017-2020 AMG C43, and AMG C63 vehicles. The front seat belts might not fully retract to their stowed position.…
Both front seat belts on the driver and passenger side fail to retract. Looking up my car model I found the following: Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2021 C300, 2017-2020 AMG C43, and AMG C63 vehicles. The front seat belts might not fully retract to their stowed position. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 208, "Occupant Crash Protection." However my vin number was not marked for the repair and the dealer refused to cover it. I ended up paying for the repair out of pocket for safety.
- Seat belts · Structure
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that after the dealer performed an unknown recall repair and Honda of Newnan (391 Newnan Crossing Bypass, Newnan, GA 30265) replaced the ball joints and axles, the contact noticed that the roof panel had detached, causing the front…
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that after the dealer performed an unknown recall repair and Honda of Newnan (391 Newnan Crossing Bypass, Newnan, GA 30265) replaced the ball joints and axles, the contact noticed that the roof panel had detached, causing the front panel to loosen, and the driver's side air bag was visible. Additionally, the front driver's side seat belt failed to retract. The dealer was made aware of the failure and referred the contact to the manufacturer. The vehicle was not diagnosed or repaired. The manufacturer was made aware of the failure and advised the contact to file a complaint with the NHTSA Hotline. The contact related the failure to NHTSA Campaign Numbers: 21V197000 (Structure) and 21V032000 (Seat Belts) however, the VIN was not included in the recalls. The failure mileage was approximately 58,237.
- Structure
The contact owns a 2017 Mercedes-Benz C43 AMG. The vehicle had previously been serviced under NHTSA Campaign Number: 21V197000 (Structure). The contact stated while driving 60 MPH, the sunroof glass was rattling. The contact pulled off the exit to check the sunroof. The vehicle was not diagnosed…
The contact owns a 2017 Mercedes-Benz C43 AMG. The vehicle had previously been serviced under NHTSA Campaign Number: 21V197000 (Structure). The contact stated while driving 60 MPH, the sunroof glass was rattling. The contact pulled off the exit to check the sunroof. The vehicle was not diagnosed nor repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure, and the contact was awaiting a callback. The failure mileage was approximately 85,000.
- Seat belts
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that the driver’s and passenger’s side front seat belt retractors had malfunctioned, and the seat belts would not retract after unlocking. The vehicle was taken to the local dealer who performed the recall repair under the NHTSA…
The contact owns a 2017 Mercedes-Benz AMG C43. The contact stated that the driver’s and passenger’s side front seat belt retractors had malfunctioned, and the seat belts would not retract after unlocking. The vehicle was taken to the local dealer who performed the recall repair under the NHTSA Campaign Number: 21V032000 (Seat Belts). The contact indicated that after retrieving the vehicle, the failure was still present. The cause of the failure was not yet determined. The manufacturer was notified of the failure. The failure mileage was 50,000.
- Seat belts
The contact owns a 2017 Mercedes-Benz C43 AMG. The contact received a recall notification for NHTSA Campaign Number: 21V032000 (Seat Belts) however, the dealer informed the contact that the part for the recall repair was not yet available. The contact stated that the manufacturer had exceeded a…
The contact owns a 2017 Mercedes-Benz C43 AMG. The contact received a recall notification for NHTSA Campaign Number: 21V032000 (Seat Belts) however, the dealer informed the contact that the part for the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was notified of the issue but provided no assistance. The contact had not experienced a failure. Parts distribution disconnect.
- Engine · Power train
Vehicle jerks very violently when accelerating or using paddle shifters (in manual mode). other owners seem to encounter same issue
- Wheels
Wheel lips on this vehicle deform with little provocation resulting in rapid air loss, loss of handling and in extreme cases a crash. the shape of these wheels deviates from other alloy wheels in a way that promotes this behavior. the curve of the rim barrel between the lips (also know as the…
Wheel lips on this vehicle deform with little provocation resulting in rapid air loss, loss of handling and in extreme cases a crash. the shape of these wheels deviates from other alloy wheels in a way that promotes this behavior. the curve of the rim barrel between the lips (also know as the bell) IS much shallower than many other wheels. the result IS that the angle at which the barrel meets the lips IS closer to a right angle than common. the barrel meeting the lip at an angle closer to parallel with the pavement greatly increase the risk that sudden deflation could occur resulting in the aforementioned safety issues.
- Unknown or other · Wheels
Documentation errors and omissions misinformation regarding proper replacement wheel. this misinformation could result in wheels with improper fit being install potentially resulting in abnormal handling, diminished braking performance and in extreme cases possible separation of the wheel from…
Documentation errors and omissions misinformation regarding proper replacement wheel. this misinformation could result in wheels with improper fit being install potentially resulting in abnormal handling, diminished braking performance and in extreme cases possible separation of the wheel from the vehicle at high speed. mercedes parts web site, https://mbparts.mbusa.com, lists parts 205-401-11-00-7x23 front and 205-401-12-00-7x23 rear as the proper replacement wheels. the selling dealer, mercedes-benz of flemington, nj insists that these are not the proper wheels but parts 205-401-48-00-7x23 front and 205-401-72-00-7x23 rear are the proper wheels. all these wheels are available from numerous resellers. purchasing and installing the https://mbparts.mbusa.com listed wheels could result in the aforementioned safety issues.
- Wheels
The wheels on my tires will crack at the slightest stress from the road. it could be a bump, a tiny pot hole, even a stick, and these tires will become defective, either by cracking, becoming flat or the wheel becoming completely immoblized. I have been stranded on the road in the middle of the…
The wheels on my tires will crack at the slightest stress from the road. it could be a bump, a tiny pot hole, even a stick, and these tires will become defective, either by cracking, becoming flat or the wheel becoming completely immoblized. I have been stranded on the road in the middle of the night for hours because of these defective tires. I've come into work un-showered with no sleep, because I was stranded for sometimes up to 12 hours before I would get help. its happened at least once a month for the past 4 years. there IS no way these tires passed even basic inspection. they are danger to anyone using them.
- Visibility › Sun/moon roof assembly
TL* the contact owns a 2017 mercedes-benz C43 AMG. The contact stated that while driving at 50 mph, there was an abnormal sound coming from the top of the vehicle. The contact inspected the vehicle and became aware of a massive fracture in the sun roof. The contact called an unknown dealer and was…
TL* the contact owns a 2017 mercedes-benz C43 AMG. The contact stated that while driving at 50 mph, there was an abnormal sound coming from the top of the vehicle. The contact inspected the vehicle and became aware of a massive fracture in the sun roof. The contact called an unknown dealer and was informed that the vehicle was not covered under warranty. The vehicle was not repaired. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was 32,929.
- Electrical system · Steering · Steering › Electric power assist system · Vehicle speed control
TL* the contact owned a 2017 mercedes benz C43 AMG. The contact stated that while driving at 63 mph in the rain, loss control of the vehicle as it sled to the left and crashed into the guard rail. The incident of march 12TH did not feel like I had hydro-planned. The contact stated that several…
TL* the contact owned a 2017 mercedes benz C43 AMG. The contact stated that while driving at 63 mph in the rain, loss control of the vehicle as it sled to the left and crashed into the guard rail. The incident of march 12TH did not feel like I had hydro-planned. The contact stated that several warning lights illuminated such as air bags failure, shock failure, suspension failure and track failure. There were no injuries and no police report was filed. The vehicle's driver's side was damaged under the front bumper and the frame was damaged beyond repair. The vehicle was towed to an auto body repair facility where the contact was informed that the steering was extensively damaged and a failure cause could not be determined. The contact researched the failure on-line and believes that the electric steering was defective and may be a cause of the failure. The contact mentioned that the vin was not included in a recall for electrical steering. During the inspection of the vehicle by penske auto collision center, the technician could not tell if the steering damage was sustained during the collision or as a result of a defect. They also found damage to the rear drive unit although, as very visible in the photos, the vehicle struck the barrier with the front left (driver's side) portion of the front bumper. The rear of the car never slammed into the barrier but did scrape along the driver's side momentarily but there was no impact. The collision center could not account for the damage to the rear drive unit. In research, I found a few mentions and complaints of the rear axle disengaging which could cause loss of control. The vehicle was totaled by the contact's insurance company. The dealer and manufacturer had been contacted. The failure mileage was 32,000. *Dt*jb
- Seats
2017 mercedes benz C43. Consumer writes in regards to front seatback lock safety recall. *Ld *js
- Seats
TL* the contact owns a 2017 mercedes-benz c43a4. The contact received notification of nhtsa campaign number: 19v130000 (seats). The contact stated that mercedes-benz of danbury (located at100 federal rd, danbury, ct 06810, (203) 778-6333) exceeded a reasonable amount of time for the recall repair.…
TL* the contact owns a 2017 mercedes-benz c43a4. The contact received notification of nhtsa campaign number: 19v130000 (seats). The contact stated that mercedes-benz of danbury (located at100 federal rd, danbury, ct 06810, (203) 778-6333) exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The part was not available for the repair. The contact had experienced a failure. Parts distribution disconnect.
- Wheels
In regard to continental tires.the wheels crack at the slightest resistance. the wheels constantly need air placed in them sometimes twice a week. in a year I have had to replace 12 tires due to cracking at the slightest impact. the wheels do not last 50 miles after being flat they are destroyed the minute they hit impact. these are dangerous tires for anyone and these need to be recalled.
- Tires
TL* the contact leased a 2017 mercedes-benz C43 AMG equipped with pirelli p zero all season tires, size: p225/40/r19 (na). On several occasions, the low tire pressure warning indicator illuminated. Also, the front driver and passenger tires experienced blowouts and cracked rims. The vehicle was…
TL* the contact leased a 2017 mercedes-benz C43 AMG equipped with pirelli p zero all season tires, size: p225/40/r19 (na). On several occasions, the low tire pressure warning indicator illuminated. Also, the front driver and passenger tires experienced blowouts and cracked rims. The vehicle was taken to mercedes-benz of nanuet (99 ny-304, nanuet, ny 10954, (845) 624-1500) to be diagnosed, but no assistance was offered. The contact stated that both front tires were replaced eleven times. The vehicle manufacturer was notified. The tire manufacturer was not contacted. The approximate tire and vehicle failure mileage was 3,997.
- Tires › Sidewall
TL* the contact owns a 2017 mercedes-benz C43 AMG equipped with continental tires. The front tires were size: 225/40/r19 93Y and the rear tires were size: 255/35/r19 96Y (na). The contact stated that the sidewalls of the tires were so thin that the tires would blow out while driving over small…
TL* the contact owns a 2017 mercedes-benz C43 AMG equipped with continental tires. The front tires were size: 225/40/r19 93Y and the rear tires were size: 255/35/r19 96Y (na). The contact stated that the sidewalls of the tires were so thin that the tires would blow out while driving over small potholes. The contact experienced six tire failures over the last fifteen months. The vehicle was taken to mercedes-benz of union (2585 US-22, union, nj 07083, (908) 379-7200) and the tires were replaced at the contact's expense. The tire manufacturer acknowledged the tire failures, but offered no assistance. The mercedes-benz manufacturer also acknowledged the failures, but blamed the contact for not purchasing the extra tire insurance at the time of purchase. The manufacturer initially offered a discount to purchase the tire insurance. The contact was later offered to end the lease of the vehicle and the manufacturer offered a discount on leasing or purchasing another mercedes-benz vehicle. The contact wanted the tires and rims replaced with standard 18-inch tires, but the manufacturer refused because the cost was too high. The tire lines, dot numbers, vin, and tire and vehicle failure mileages were not available.
- Service brakes
The parking brake won't release sometimes after doing everything that the manual and mercedes benz recommends. I've been stranded for over 30 minutes. I've pulled the brake release for over 10 seconds and put the car in gear and turned if off and on. twice the parking brake light has come on when driving.
- Service brakes
At start-up, the parking brake light comes on and can't be turned off. This happened several times. The parking brake light comes on while driving one day at start-up the brake would not release for 30 minutes while trying various methods recommended by mercedes benz support and the operators…
At start-up, the parking brake light comes on and can't be turned off. This happened several times. The parking brake light comes on while driving one day at start-up the brake would not release for 30 minutes while trying various methods recommended by mercedes benz support and the operators manual. the brake light has come on when it starts up and the parking brake could not be released preventing the car from moving. Also the warning light comes on when driving. I will upload a picture of this.
- Wheels
Tire failure while driving. Tread separated from sidewall. Maybe related to pirelli recall 16t018000. Tire manufactured 05-17 and dot ce X2 T120 and ece homologation symbol IS E4 0271937.
- Air bags
Vehicle has insufficient electrical grounding that can lead to an inadvertent deployment of the driver airbag. mercedes refuses to inform me of a date that the vehicle will be repaired. I was sent a letter from mercedes dated november 2017 and the dealers and the manufacture will not give me a…
Vehicle has insufficient electrical grounding that can lead to an inadvertent deployment of the driver airbag. mercedes refuses to inform me of a date that the vehicle will be repaired. I was sent a letter from mercedes dated november 2017 and the dealers and the manufacture will not give me a date. I am unsure as I drive the auto that the airbag will deploy causing and accident and injury to myself. why can't the vehicle be repaired in a timely manner? I am now in the 5TH month and wondering if I am driving a time bomb.
- Electronic stability control (esc) · Engine · Power train
The car enters limp mode in the highway where it looses all the power and warning pops up as active brake assist IS inoperative, traction control lights come on as well. If you manage to glide the car to a stop and restart the car, the car starts to back up as normal. took the car for service…
The car enters limp mode in the highway where it looses all the power and warning pops up as active brake assist IS inoperative, traction control lights come on as well. If you manage to glide the car to a stop and restart the car, the car starts to back up as normal. took the car for service several times, intake airflow sensor was replaced but the car still has the same issue. Upon searching online, this IS a very well known issue with the newer mecedes cars where the car goes into a safety mode where the engine cuts all the power turning the situation into a even more dangerous scenario. As part of the safety mode, if the car looses all the power, then there IS few things that can be done to come out of it. this IS a major safety concern as repeated occurence of this problem has the ability to cause a severe accident.
- Air bags
Takata recall I recieved the notification from takata airbag inflators at home. I called my dealer and they didn't agree that my car have a recall for airbags. I called the mercedes benz principal office and they also denied I have problmes with airbags. The website of airbagrecall.com showed…
Takata recall I recieved the notification from takata airbag inflators at home. I called my dealer and they didn't agree that my car have a recall for airbags. I called the mercedes benz principal office and they also denied I have problmes with airbags. The website of airbagrecall.com showed active recalls when I put my vin number it showed that I have the problem.oct 6 2017 recall number 17v627.manufactures recall number 2017100005. I feel in risk to drive my car and I need it urgent. Please I need help.
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010907Complaint The flap of the reversing camera opens and closes by itself during forward travel. This happens several times during the trip. The customer notices the sound of opening and closing. No camera image is displayed in the head unit. The reversing camera or the 360 system functions normally when activated manually or by engaging drive range "R". This behavior occurs again during each driving cycle. Cause This is not a malfunction, but an intended system behavior: Calibration of the reversing camera is in progress. For this, the cover on the camera is opened for max. 5 cumulative minutes in forward travel. The calibration can be performed if the vehicle speed is < 35 km/h and the steering wheel angle is < 10 (for early vehicles from MFA2 facelift model series such as A-Class, CLA, etc., the 35 km/h (~22 MPH) opening limit may only be reached after the SCN coding is replaced). If the speed of 35 km/h (~22 MPH) is exceeded, the camera retracts and the calibration is therefore aborted. The sequence is started again once the speed returns to the range of 18 km/h (~11 MPH). Remedy Complete the calibration successfully. For this, the vehicle must be driven forwards for a certain time (usually significantly less than one minute) at a speed < 35 km/h (~22 MPH) and a steering wheel angle < 10. This should occur during daylight and without a vehicle following too closely (the camera must be able to see the asphalt). When calibration is successful, the camera flap closes automatically at an unchanged speed. For the rest of the driving cycle, the camera now only opens if the customer requests this, for example by applying the reverse gear. When starting a new driving cycle (ignition change), another calibration is required. The customer can generally perform calibration at the first attempt when a speed in the range between 15 km/h (~9 MPH) and 35 km/h (~22 MPH) is briefly maintained and can therefore play a significant role in reducing the actuation frequency and therefore also the noticeability of the noise to a minimum. In the case of early MFA2 facelift vehicles (A-Class, CLA, etc.), the parking control unit may have to be SCN-coded again to have the complete speed window available for the calibration.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11010455Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case according to WIS specifications After please complete all transfer case Tech-in processes located under VG control unit Adaptations tab - Resetting the oil service data - Calibration of N15/7 Perform road test of vehicle to bring transmission to operating temperature ( >60C ) Operate vehicle in full circle with steering at full lock - 5x to the left - 5x to the right Reassess the vehicle following the oil change and teach in If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008880Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008064In our continuing efforts to ensure the proper performance and quality of your vehicle, we are writing to inform you that on certain Model Year 2011-2018 C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. Therefore, an Emission Service Campaign is being conducted to remedy the situation. Our records indicate that your vehicle is included in the affected population of vehicles.
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11007728Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LIs before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case number if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to confirm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the same repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after adaptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack. IF more than 3 are red and NOK replace transmission (include printout with warranty claims) **** FOR 167 chassis with M264 engine B08 may be red and NOK, IGNORE this, B08 is still okay **** Shift complaints: Note: AMG variants are known to have a harsher shift see LI27.60-P-075147 It is always worth comparing to a like vehicle if possible to see if shift is uncharacteristic Perform Valve flushing procedure Perform 5 Torque Converter adaptions in a row (Save the results page) Perform standstill adaptions (Save the results page) Drive adaptions if necessary: Drive C mode keep RPM between 2000-2200rpm and lightly let off pedal to force shift wait 2-3 sec then roll on throttle to rpm back up to 2000-2300 rpm repeat for gears 1-3 *For gears 4-8 allow rpm up to 2700 and let off slightly to force upshift = repeat x 10 *For downshift - highest gear possible 8 or 9 - allow decel with light brake drag (allow at least 5s between downshifts for trans to adapt. Go down to 2nd and repeat x10 *Change to sport mode and repeat process again *Lock car to allow sleep at least 10min and restart and road test for quality. After adaptions a new EEPROM should be recorded and included with the original if opening a case Understand shift complaints need to be reproducible to address. If needed drive with client to reproduce the complaint. If shift complaint is intermittent a CAN trace of the issue occurring will be useful (see attached instructions) Shudder: If there is a shudder monitor torque convertor actual values to see if it occurs during slipping, Additionally can lock up convertor and drive to see if issue is resolved Jolting/Shudder: If the vehicle is AWD: unplug AWD control unit or drive vehicle in dyno mode to see if transfer case is causing the jolt/ harsh shift If located from transfer case check fluid and perform a flush if needed to try to rectify the issue. Vibrations: NVH trace is needed, what level vibration is being experienced and where is it located? Is the Vibration felt in neutral? Dyno mode? Does it change with speed? Etc. Noise complaint: Isolate the noise location using chassis ear. MUST attach a sound recording or video of the noise. Describe when the noise is present: Does it change with gear or speed? Does it occur with vehicle in neutral or in glide mode? Does operating temperature effect noise? Does incline/decline or steering angel effect noise?
- 11006658Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz vehicles, has determined that on certain Model Year (MY) C-Class, E-Class, S-Class, G-Class, CL, CLS, ML, GL, GLE, GLS, GLC, SL, and AMG GT (204, 205, 207, 212, 213, 217, 221, 222, 463, 216, 218, 166, 292, 253, 231, and 190 platforms) vehicles with 6 and 8 cylinder gasoline engines, the software of the engine control unit may not meet current specifications. Under certain conditions, the catalyst heating might not work. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will update the engine control unit software on the affected vehicles. Affected customers will be notified via First Class letter to have the update performed on their vehicle.
- 11005344Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process. Cause As part of the on-going quality monitoring process and associated quality and damaged part appraisals, a high number of ineffective repairs have been discovered. Such ineffective repairs have a negative impact on all those involved. For the customer, it means high costs and long repair times and for the dealer, it may result in the warranty claim being rejected. Remedy General note: IPR is available for: NAG3 Classic (automatic transmission 725.0) NAG3 - AMG sports models (AMG 43 and AMG 53 with converter) NAG3 - AMG 63 NAG3 - Hybrid
- 11005331Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain' (PTCU) control unit Y3/8 - Transmission control for 9-gear transmission (VGS) N3/10 - Engine electronics for combustion engine If faults are present, process them as per the guided test in Xentry If no faults are present: Check the oil level of the transmission If the oil level is correct: Unplug the connector for the transfer cases control unit Reassess the vehicle on a subsequent test drive If the complaint no longer occurs: Perform an oil change of the transfer case Reassess the vehicle following the oil change If the problem continues to occur with the plug removed or after the oil change has been carried out: Create a TIPS case with the following data Initial quick test with fault freeze frame data EEPROM data from Y3/8 Transmission control unit EEPROM data from N45 All-wheel drive Injector performance data
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 11000598Complaint Noticeable vibrations at the steering wheel: At speeds between 40mph and 75mph On straight stretches of road and in long corners With driver assistance systems switched on Cause Control oscillations in the electric power steering. Remedy Perform software update of electric power steering (N68). Note: Please ensure newest Xentry release software is installed and all addons are updated. After the software update, teach in the steering limitations of the electric power steering again: 1. Start engine 2. Turn steering wheel all the way to the left and briefly hold at the steering limitation 3. Turn steering wheel all the way to the right and briefly hold at the steering limitation 4. Perform a test drive in which you drive at approx. 5-10 km/h in an "8" shape, alternately turning the steering wheel to the steering limitations on the left and right. If vibrations can still be felt following the software update: 1. Connect XENTRY and select control unit N68 - Electric power steering (ES) 2. Switch to the "Adaptations" menu item, then under the "Teach-in processes" item, run the "Special function" in full. With this function, parameters of the software are adapted to reduce vibrations in the steering wheel. If vibrations continue to occur in the steering wheel despite this action, please create a TIPS case.
- 10249726Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration. This free of charge update includes quality-enhancing optimizations for the communication module to improve the system stability and better availability of the Mercedes me services. The update is downloaded and installed in the background. This process takes approx. 15 minutes. During the installation, the system can be used without restrictions. The new software will be active after the vehicle has been switched off. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customers vehicle free of charge without an additional workshop visit via the data link of the communication module. All customers will be mailed a letter informing them of this software update.
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10244837The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
- 10238437Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (MY) 2016 2021 C-Class (205 platform), E-Class (213 platform) and GLC (253 platform) vehicles, the air conditioning control unit software may not meet production specifications. There is a possibility that a stuck open thermostat may wrongly be detected causing the check engine Malfunction Indicator Lamp (MIL) to illuminate. MBUSA will conduct an Emission Service Campaign. An authorized Mercedes-Benz dealer will perform a software update to the air conditioning control unit on the affected vehicles.
- 10233783Complaint Loads induced at the steering wheel through pushing and pulling actions may cause creaking and cracking noises in the mechanical steering column. Cause Insufficient grease lubrication in the clamping area of the mechanical steering column. Remedy Grease the clamping area.
- 10231031Staining on door trim strips and top and bottom trim elements on rear side windows. Cause Damage to protective coating of door beltline trim strips, door upper trim strips and side window trim element. Remedy 1. Check if the problem cannot be rectified by polishing the trim bars with the polishing paste. 2. If the complaint cannot be rectified, replace the door beltline trim bars, door upper trim bars and rear side window with trim element with optimized protective coating.
- 10217162Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10217157Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
- 10217154Complaint Thumping noise on rear axle shock absorber on rough road. Cause Until now the rear axle shock absorber support bushing was only available together with the rear axle shock absorber as a replacement part. In future, the rear axle shock absorber support bushing will be available individually as a replacement part to avoid any unnecessary shock absorber noise. Remedy For noise problems on the rear axle shock absorbers, please always make a noise diagnosis, for example using Chassis Ear to localize any sources of noise on shock absorbers or support bushings. If the noise originates from the upper part of the shock absorbers, it is enough to replace the support bushings. Otherwise the complete shock absorber including support bushing have to be replaced. The modified support bushings must be replaced in pairs the first time so that any mixed installation of old and new is reliably ruled out.
- 10215212Complaint Customer may have one or more of the following complaints: Vehicle location is shown incorrectly in the Navigation Display Navigation destination search is not possible Street names are not shown in Navigation display Apple Carplay is inoperable Cause Improper installation of navigation map data Remedy Follow these steps to delete and re-install map data: Re-format an empty USB drive to NTFS (do not use quick formatting option) Unzip the attached map data deletion file directly to the USB drive. Do not add a folder, only the root files should be shown on the USB drive Generate a pin for the Navigation Delete Database in Vedoc (see attached screenshot) Plug USB drive with map data delete file into the vehicle's USB port and follow instructions in the COMAND Display to delete the installed map data Once the originally installed map data is deleted, then install the newest available map data in Download Manager
- 10209874Mercedes-Benz AG (MBAG), the manufacturer of Mercedes-Benz, has determined that on certain MY 2015-2018 C-Class and GLC-Class (205 and 253 platform) vehicles, the software for the powertrain control unit may not correspond to the current production specifications. It is possible that the next maintenance interval is displayed to the user as a negative distance reading in the instrument cluster. What Were Doing MBUSA will conduct a service campaign. An authorized Mercedes-Benz dealer will update the powertrain control unit software.
- 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
- 10206077"MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 Boost Pressure is Too High"" "
- 10205837Model series 190.4 Anti-theft alarm activates without obvious cause.
- 10205814Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
- 10205807The Weather App will not populate local weather data based on current vehicle position.
- 10205804Insufficient charging or no wireless charging with iPhone 12.
- 10205266Map pocket on front seat backrest trim does not close.
- 10205257Model indicator index.
- 10205241Navigation system permanently displays "Activating".
Every Mercedes-Benz AMG C43 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.