2010 Mercedes-Benz AMG C63

Recalls

2 recalls name the 2010 Mercedes-Benz AMG C63. Newest first.

• Air bags › Frontal › Passenger side › Inflator module

  Jan 9, 2019NHTSA 19V010000288,779 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and…

  Risk and remedy

  Risk

  An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

  Remedy

  MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

  Full recall details →

• Air bags › Frontal › Passenger side › Inflator module

  Jan 10, 2018NHTSA 18V043000132,167 vehicles

  Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of…

  Risk and remedy

  Risk

  An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

  Remedy

  MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

  Full recall details →

Owner complaints

Latest complaints

• Dec 10, 2018TX
  Exterior lighting

  Mercedes benz c class. Consumer writes in regards to rear tail light bulb carrier safety recall. *Ld the consumer stated the manufacturer exceeded a reasonable amount of time completing the recall repair. *js

Service bulletins

Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.

• 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
• 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
• 11008873Complaint Tension-releasing impact of the propeller shaft with the force-free in D "KID" function, after vehicle has stopped. Cause The tension-releasing jolt in the drivetrain originates as a result of the "release" of energy stored when braking through the force-free switch after stopping. It is suspected that the longitudinal bearing is being placed under tension here as a result of the vehicle "dropping off". Remedy 1. Mark the installation position of the joint prior to the removal (picture a+b). This is important for vehicles with a weighted drivetrain ex factory to ensure correct installation after operations have been completed. 2. Clean and degrease propeller shaft toothing. The toothing must be free of grease, e.g. through the use of a brake cleaner. Do not use wire brushes, else the surface could be damaged (picture c). 3. Coat propeller shaft toothing with A 000 989 16 08 Antifriction coating. Coat the entirety, ensuring that the subsurface is no longer visible. When doing so, only coat the outer toothing. Ensure that the coat is not too thick, otherwise the coating could chip (picture d). 4. Observe the drying time of at least 1 hour. 5. Lightly grease the propeller shaft toothing at the outer and inner toothing with A 001 989 44 51 12 Grease (picture e).
• 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
• 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
• 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
• 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
• 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
• 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
• 10252770As previously reported, to enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a Settlement regarding claims relating to allegations that the 590 Mars Red paint available as an original, exterior color option for certain models of Mercedes-Benz vehicles may experience peeling, flaking, or bubbling of the exterior paint or clear coat. This Mars Red paint is sometimes referred to as Fire Opal. The purpose of this update is to alert you that: 1. The Settlement has received final approval. The Settlement will go into effect on March 11, 2024. As of that date, customers are eligible to receive extended warranty coverage under the Settlement. 2. Under the Settlement, an eligible customer might receive extended warranty coverage as of the date the vehicle is presented to your dealership OR certain customers might have validated Qualified Future Repair claims, making them eligible for a different level of coverage. To determine if a customer: (a) is eligible for extended warranty coverage; and (b) what level of warranty coverage is available to them, please refer to the Service Packages section in VMI/Netstar. 3. Damage code 21800 (damage type 00) must be used for warranty claims covered pursuant to the Settlement. Please note that you should only claim for the percentage of warranty repair cost reflected in VMI/Netstar (see below, e.g., for Period Two, claim only 50% of warranty repair cost). 4. Before the dealership agrees to perform any work: The customer should be given a Repair Order containing: (1) an estimate for the repair, (2) the portion covered under the extended warranty; and (3) the customers contribution amount for the repair, if applicable. The customer must agree to pay their contribution amount for the repair and sign the Repair Order before the repair is performed.
• 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
• 10246055In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the warranty coverage on the fuel filter unit for Partial Zero Emission Vehicles (PZEV) from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 15 years/150,000 miles (whichever occurs first), and applies to the vehicle regardless of ownership. Why the warranty extension? On certain Model Year 2010 2011 C / E / GLK Class Mercedes-Benz vehicles, a potential fuel seepage from the fuel filter flange could result in the fuel odor and/or an activation of the check engine Malfunction Indicator Lamp (MIL). . Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. If your preferred authorized Mercedes-Benz dealership performs a diagnosis and confirms that your vehicle has the issue, the repair will be covered under this extended warranty and performed at no cost to you. This extended warranty does not apply to any other components or conditions beyond the ones mentioned above, and standard warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet.
• 10235996Additional information around the recent recall announcement affecting approximately 705,983 Mercedes-Benz passenger vehicles involving Takata driver-side airbags containing PSDl-5 type inflators
• 10235978Recall Campaign announcement for Takata driver airbags.
• 10235972Enclosed for your information and pursuant to part 579.5, please find our latest Service and Warranty Bulletins for March, 2016
• 10233796Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the even the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10233780Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) WIS reference 2005 - 2011 SLK-Class (R171) AR35.10-P-0010V 2012 - 2017 SLK-Class (R172) AR35.10-P-0010V 2012 - 2016 CLS-Class (C218) AR35.10-P-0010EW 2013 - 2016 SL-Class (R231) AR35.10-P-0010RK 2008 - 2015 C-Class Sedan/Coupe (W/C204) AR35.10-P-0010CW 2010 - 2015 GLK-Class (X204) AR35.10-P-0010CW 2010 - 2016 E-Class Sedan/Wagon (W/S212) AR35.10-P-0010EW 2010 - 2017 E-Class Coupe/Cabrio (C/A207) AR35.10-P-0010CW All models require cavity preservation on the rear axle carrier after the replacement according to AR35.10-P-0010-03A.
• 10232321Mercedes-Benz USA, LLC (MBUSA) has extended the warranty for the rear subframe on the vehicles listed below, from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 20 years/unlimited miles, and applies to the vehicle regardless of ownership. This warranty extension applies to the replacement of the rear subframe under the standard warranty terms and conditions in the event the subframe experiences corrosion with perforation (holes). The extended warranty is applicable to the following vehicles: Model Year Model (platform) Model Year Model (platform) 2005 - 2011 SLK-Class (R171) 2008 - 2015 C-Class Sedan/Coupe (W/C204) 2012 - 2017 SLK-Class (R172) 2010 - 2015 GLK-Class (X204) 2012 - 2016 CLS-Class (C218) 2010 - 2016 E-Class Sedan/Wagon (W/S212) 2013 - 2016 SL-Class (R231) 2010 - 2017 E-Class Coupe/Cabrio (C/A207) Only the following damage code can be claimed for the replacement of the rear subframe due to corrosion with perforation: Damage Code: 35441 47 Always check VMI to determine if a vehicle is covered under this 20 years/unlimited miles extended warranty. Please
• 10207199Complaint The range of the integrated garage door opener (GTO) is too short. Cause 1. Vehicles equipped with infrared windows and/or a heated windshield may suffer from complaints involving low transmission power. 2. When comparing the range between the integrated GTO and the garage door hand transmitter, the garage door hand transmitter is tested outside the vehicle. 3. The garage door hand transmitter is being aimed towards the garage door, but the vehicle is in a different position. 4. The garage door drive is old. Remedy 1. The lower level of transmission power is mainly perceived by customers who did not have any infrared windows (code 595) or all-round infrared windows (code 596) or heated windshield (code 597) in their previous model or who have another model without this special equipment in their fleet. The loss in transmission has technical reasons, i.e. a thin metal film is fitted in the windows. Please consider these codes and advise the customer accordingly! Replacing parts does not remedy the problem. 2. Perform the comparison test between the integrated GDO and the garage door hand transmitter under identical conditions. The garage door hand transmitter must be inside the vehicle and must be held at the height of the inside rearview mirror. 3. The customer instinctively aims the garage door hand transmitter towards the door. However, the transmission direction of the integrated GDO depends on the position of the inside rearview mirror, and thus depends directly on the position of the vehicle relative to the receiving antenna of the garage door drive.
• 10207198Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3. When the handheld remote control is initialized with the integrated GDO, the distance between the handheld remote control and the GDO is too long or too short. 4. The maximum programming time of the hand transmitter was exceeded. The hand transmitter switches itself off after 10s to 20s. However, the garage door opener needs up to 30s to learn the code. 5. The maximum programming time of the integrated GDO was exceeded. The integrated GDO has aborted programming unsuccessfully. 6. The GDO cannot be programmed after replacement (See #9). 7. The batteries of the hand transmitter are too weak. 8. A part of the signal was not registered correctly. 9. The GDO is not programmed to US standards. 10. Errors with Chamberlin MyQ, Liftmaster MyQ, or Craftsman AssureLink systems causing loss of synchronization. Remedy Note: The numbering of the remedies refers to the numbering of the causes. 1. Installation of a universal receiver. Order via the Homelink Hotline. 2. In the case of garage door drives with rolling code system, synchronization of the garage door drive must also be performed. 3. Keep the correct distance when initializing! This can vary between 5 and 20 cm depending on the system. If the initialization attempt is unsuccessful, repeat the initialization process, changing the distance between the hand transmitter and the mirror.
• 10205790After starting the engine, the instrument cluster shows the "EBD not available, diagnosis/test stand" message in yellow.
• 10205265Outside mirror fogged.
• 10205239"Anti-theft protection activated".
• 10205237The COMAND unit does not start or the display remains dark.
• 10205234Software update of COMAND Online control unit.
• 10205233Mobile phone cotacts are not transferred completely.
• 10205225Headlamps fogged.
• 10205150Engine sound change after recent software updates.
• 10186141NTG5.5: Incorrect time shown on instrument cluster, COMAND display, and analog clock
• 10186135If the customer brakes sharply from a speed of > 30mph, without ABS intervention, there is a single cracking noise from the area of the ESP hydraulic unit
• 10181124Harsh engagement when changing gear range from P to D or R
• 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
• 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
• 10167564Customer experiences low battery conditions, resulting in jump starts, and eventually requiring battery replacement.
• 10167563The COMAND unit does not start or the COMAND display remains dark. The COMAND unit cannot be operated. Note: The problem disappears after a lengthy idle period (>6h) or after interrupting the power supply (circuit 30).
• 10167560Fault message in display - Right rear turn signal light inoperative
• 10167554Engine diagnosis warning lamp activated. Fault code P045600 "Very fine leak" or P044200 "Fine leak" stored in engine control unit.
• 10167552Engine does not start, or various fault messages in instrument cluster immediately after engine start and servo assistance is reduced. The following display messages may appear: - Red message "Power Steering Malfunction - See Operator's Manual" including acoustic warning - Red or yellow message "ESP / ABS Currently Unavailable - See Owner's Manual", sometimes with acoustic warning - White message about tire pressure monitor or run flat indicator: "Tire Pressure Loss Warning Defective" or "Tire Pressure Monitor Defective" In addition, the indicator lamps of the following systems may light up: - Brakes / ABS / ESP / ESP Off / engine diagnosis Furthermore: - The chassis CAN is partially or completely disrupted - Several control units (e.g. the electric power steering, ESP, engine etc.) cannot be interrogated or are not listed in the quick test - Various CAN communication errors from other control units may be logged (see list "Control unit / Fault code")
• 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
• 10167546FC 2783 (Friction power of torque converter lockup clutch is too high) or FC 0741 (Actuation of torque converter lockup clutch not possible) stored in transmission control unit. One possible additional customer complaint could be "poor acceleration" e.g. due to engine intervention. This can affect all NAT2FE+ (7G-TRONIC PLUS) vehicles with engines OM651, OM642LS and M278 in the production period from 04/2011 to 02/2012 and with more than 10,000 km. The two fault codes can also occur in combination with rpm sensor faults (see also GI27.50-P-035556). The rpm sensor fault is not connected with this complaint.

Every Mercedes-Benz AMG C63 model year

Bars are owner complaints, dots mark years with recalls. Select a year to open its report.