2014 Mercedes-Benz AMG CLA45
Safety record from NHTSA: recalls, owner complaints, investigations and service bulletins.
Have the VIN?
Vehicles › Mercedes-Benz › AMG CLA45 › 2014
These records cover every 2014 Mercedes-Benz AMG CLA45. To see whether one car still needs a recall repair, decode its VIN or check it with NHTSA.
Recalls
5 recalls name the 2014 Mercedes-Benz AMG CLA45. Newest first.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014-2020 C-Class, CLA, GLA, S-Class, GLC, and GLE vehicles. Please refer to MBUSA's recall report for specific vehicle details. The front roof panel located between the windshield and the panoramic sunroof may not have been bonded correctly to the vehicle during a prior repair, allowing the front panel…
Risk and remedy
Risk
A detached roof panel can become a road hazard, increasing the risk of a crash.
Remedy
Dealers will replace the front panel, free of charge. Owner notification letters were mailed on August 2, 2024. Owner notification letters will be mailed in phases, on, March 22,2024, and August 2, 2024. Owners may contact MBUSA customer service at 1-800-367-6372. This recall is an expansion of NHTSA recall number 21V-197.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2017-2020 C300 Coupe, C43 Coupe AMG, C43 AMG, 2015-2020 C300, GLA250, 2016-2018 C350e, CLA45 Coupe AMG, 2015 C400, S65 AMG, 2015-2019 C63 AMG, 2016 C450, 2015-2016 GLA45 AMG, S600, 2016-2020 GLC300, 2017-2019 GLC43 AMG, GLE43 Coupe AMG, 2014-2019 CLA250 Coupe, 2014-2015 CLA45 AMG, 2018 GLC63 AMG, 2014-2017…
Risk and remedy
Risk
The adhesive bonding of the front panel might deteriorate, possibly causing the front panel to detach from the vehicle and become a road hazard, increasing the risk of a crash.
Remedy
Mercedes-Benz dealer will remove the bonded panel and will install a new front panel by following the detailed repair instructions and using the approved primer, cleaner and adhesive, free of charge. Owner notification letters were mailed on September 3, 2021 and October 26, 2021. Owners may contact MBUSA customer service at 1-800-367-6372.
Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit…
Risk and remedy
Risk
An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.
Remedy
MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.
Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec…
Risk and remedy
Risk
If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.
Remedy
MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.
Mercedes-Benz USA, LLC (MBUSA) is recalling certain model year 2014 CLA 250C vehicles manufactured September 10, 2014, to September 11, 2014, 2014 CLA 250C 4Matic vehicles manufactured September 13, 2014, to September 25, 2014, and 2014 CLA 45 AMG 4Matic vehicles manufactured September 10, 2014, to September 25, 2014. The affected vehicles have fuses that…
Risk and remedy
Risk
If the fuses were not properly installed, they may lose electrical contact. In the event of a loss of electrical contact, certain systems may be impacted, including the function of the front passenger seat occupancy recognition system, the passenger side air bag indicator lamp, the instrument cluster and the windshield wipers. Should the function of the front passenger seat occupancy recognition system or the passenger side airbag indicator lamp be affected, the risk of injury for passengers in the event of a crash would be increased. Should the function of the instrument cluster and the windshield wipers be affected, the risk of a crash would be increased.
Remedy
MBUSA will notify owners, and dealers will inspect the position and orientation of the fuses, and if necessary, replace the fuse box, free of charge. The recall began on August 18, 2015. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2015060007.
Owner complaints
16 complaints
What owners report most
Latest complaints
- Structure
The contact owns a 2014 Mercedes-Benz AMG CLA45. The contact stated that while driving approximately 65 MPH, the glass panel between the front windshield and the sunroof suddenly detached. The contact inspected the vehicle and found information on NHTSA Campaign Number: 23V854000 (Structure). The…
The contact owns a 2014 Mercedes-Benz AMG CLA45. The contact stated that while driving approximately 65 MPH, the glass panel between the front windshield and the sunroof suddenly detached. The contact inspected the vehicle and found information on NHTSA Campaign Number: 23V854000 (Structure). The dealer was contacted and informed the contact the VIN was not included in the recall. The vehicle was not repaired. The manufacturer was informed of the failure and confirmed that the VIN was not included in the recall. The failure mileage was approximately 75,000.
- Visibility/wiper
The ‘Sunroof shade’ malfunctioned. Just randomly came off-track. Yes, it is still available to inspect. Shade now hangs down and rises a safety concern for visibility. Not inspected by a dealer or other representative yet. No warning lights or failure notices are present.
- Electrical system · Fuel/propulsion system · Unknown or other
Vehicle appears to be a different vehicle or possibly a cloned vehicle according to fbi records . Safety does not match up nor specs with the vehicles vin report or carfax . Possibly a duped vehicle. Claims rear cam no camera specs show vehicle to be electric or blue liquid propeled . App do not work sat says its connected to the vehicle but not this one.
- Tires · Tires › Pressure monitoring and regulating systems
New tire replacement after a faulty tire. TPMS not registering correctly, rim leak from imporper sealing and now tire had a small tear had to be pluggled
- Electrical system · Engine · Fuel/propulsion system
.I purchased brand new vehicle from carmax of oaklawn , who imported the vehicle from naperville il it came with 90 day gaurantee or money back.i then drove to florida 2 weeks after purchase of the vehicle of which my boyfriend [xxx] at the time can attest the vehicle drove amazing.upon my arrival…
.I purchased brand new vehicle from carmax of oaklawn , who imported the vehicle from naperville il it came with 90 day gaurantee or money back.i then drove to florida 2 weeks after purchase of the vehicle of which my boyfriend [xxx] at the time can attest the vehicle drove amazing.upon my arrival I was having electrical issues with the eco drive and the computer coded and disappeared 3 times. I contacted carmax 800 number they advised me to bring it to the daytona beach automall carmax who then ref me to the daytona automall mercedes benz dealer to be serviced. Mercedes serv rep "said we dont deal with carmax" and sent me back to carmax after my serv rep instructed me to bring the vehicle there. So then I went to carmax who then delivered the vehicle to mercedes benz of daytona. I was given a loaner vehicle of which my personal items disapeared from "conviently legal documents and files" they replaced both batteries in the vehicle and (4)tires claiming it would fix the prob . Soon as I picked up the vehicle I informed them that it was not right and needed the advisor to contact me asap. I continued to have multiple electrical, fuel and computer indications. The vehicle IS not the same car. I also compared my vin number through mercedes and expressed a different model of vehicle. They claimed that it was do to system being outdated and that there IS no update for it. So why do my emergency safety items show an electric car ? Different model the car states its a cla 45 AMG. Fuel burns very quickly engine IS louder and I am noticing a graying in my hands after excess driving almost like blistering , the engine sound IS not correct and the computer keeps jumping hundreds of miles saying its over the package in an excess of 200 miles per day at times . Tpm system IS not working correctly. Mileage IS not recording accurately, pass air bag safety goes off, of which I addresed the poss recall I found. they refused to speak with me or return calls. Information redacted pursuant to the freedom of information act (fo
- Tires › Pressure monitoring and regulating systems
Tire tread tore from the inseam of tire causing me to be stranded out of state for 2 days waiting on means of a new tire . The vehicle pulls and now has needed a second tire replacemnt on same side. Consistant warning from tpm rim bent causing rim leak on current tire. Yes a tire service center replaced the tire completely failed to acknowledge bent rim .
- Electrical system · Engine · Structure › Body
I purchased my vehicle early March from Carmax. They offer a 90 day guarantee on anything that will go wrong with the vehicle full coverage. My daughter was having my grandchild so what a great opportunity but to drive my new vehicle from Chicago to Florida to give it a good run when I arrived I…
I purchased my vehicle early March from Carmax. They offer a 90 day guarantee on anything that will go wrong with the vehicle full coverage. My daughter was having my grandchild so what a great opportunity but to drive my new vehicle from Chicago to Florida to give it a good run when I arrived I was having problems with the Eco drive, which is the start stop enabler. The car would die out. Also, there were a few alarms as far as the temperature of the vehicle and the service mechanism being that I had left at the dealership at 9:30 PM at night and hit the road immediately I had to notice until the morning, but there was some cracking on the exterior of the driver side tire. Upon arriving to Florida. I brought the car directly to Mercedes at the Daytona auto Mall soon as I walked in they service representative stated we don’t deal with Carmax and I said well they said the car is covered under warranty to go ahead and bring it into you guys and they will take care of the bill. They made a big fuss about it saying that it needed to go to Carmax then Carmax needed to bring them the vehicle even though I had all of my stuff located in the vehicle for traveling then they proceeded to tell me that they would not give me a loaner car during the time of my service. The Carmax representative that I spoke with in service his name was Al when I had addressed all of my concerns he had mentioned due to the tire issue. They would be replacing all four tires and that they would address the issues with the Start stop control the computer reacting and then disappearing, and also a safety recall that I had noticed about the airbags because the passenger side airbag kept displaying a blinking needless to say, after being totally inconvenienced, they have my vehicle for over a week. The second I went to pick up the car. I had to pick it up in the afternoon due to having to work in the evening they had it ready in the express. There was multiple damages to the vehicle, physical eng tire
- Structure › Body
While driving on the freeway the glass piece between the windshield and sunroof flew off of the car, causing a major safety hazard.
- Visibility › Sun/moon roof assembly
The contact owns a 2014 Mercedes-Benz CLA45. The contact stated while entering the vehicle, he noticed that the sunroof slider was damaged. The vehicle was not diagnosed or repaired. The manufacturer was not notified of the failure. The approximate failure mileage was 70,000.
- Power train › Driveline › Differential unit
The contact owns a 2014 Mercedes-Benz AMG CLA45. The contact stated while driving 30 MPH, the contact heard a grinding sound coming from underneath the rear of the vehicle. The contact stated no warning light was illuminated. The contact pulled over safely but found no issues. The contact took the…
The contact owns a 2014 Mercedes-Benz AMG CLA45. The contact stated while driving 30 MPH, the contact heard a grinding sound coming from underneath the rear of the vehicle. The contact stated no warning light was illuminated. The contact pulled over safely but found no issues. The contact took the vehicle to the local dealer, where it was diagnosed with needing the rear differential to be replaced. The dealer changed the differential fluids but did not replace the rear differential. The contact drove the vehicle home and noticed that the vehicle was leaking fluid. The vehicle was not repaired but was pending repairs. The manufacturer had not been informed of the failure. The failure mileage was approximately 60,000.
- Power train
I just replaced the valve body in my vehicle and the problem IS still there I was a mercedes-benz technician and some friends advise me to do this but then I got the code that said that the Y3/14 which IS listed in the 2016 models. This was the same problem I was having as described in the…
I just replaced the valve body in my vehicle and the problem IS still there I was a mercedes-benz technician and some friends advise me to do this but then I got the code that said that the Y3/14 which IS listed in the 2016 models. This was the same problem I was having as described in the campaign. I have uploaded a photo which shows the same white 3/14 from the scanner. Mileage 49K euro motorcar would not warranty trans. Please advise [xxx] mercedes-benz USA, llc 303 perimeter center north, suite 202 atlanta, ga, 30346 phone: (770) 705-0600 fax: (770) 705-0117 mbusa.com to: mercedes-benz dealer principals, general managers, sales managers, service managers, parts managers from: [xxx], department manager, vehicle compliance and analysis, engineering services re: recall campaign 2016060005 model 117 (cla), model year 2016 replace dual clutch date: june 20, 2016 important recall launch information this recall campaign IS being launched today and the 1 affected vehicle IS flagged in vmi. Given this notice, it IS a violation of federal law for a dealer to sell or lease any of these new model year 2016 GLE coupe vehicles covered by this notification in dealer inventory until the vehicle has been repaired. Parts: parts are available. What should customers do: customers may continue to drive their vehicles until the recall IS completed. What's the issue: daimler ag has determined that on certain cla-class AMG vehicles (117 platform), a potentially defective weld between the clutch disk and hub may develop a crack. If the entire weld cracks through no traction would result at this clutch. The gearbox could then either shift into 'neutral' or go into a partial gearbox limp home mode. In the event of a shift into 'neutral' there would be no torque from the powertrain and the vehicle would coast to a stop. information redacted pursuant to the freedom of information act (foia), 5 u.s.c. 552(B)(6).
- Air bags
On 12/26/19 contacted benz dealer in west caldwell, nj. Explained to rep. That there was a recall on my vehicle for faulty airbags that when they are deployed had metal and could cause harm or death to passengers. the rep indicated that they do not know when my airbags would be replaced. she put…
On 12/26/19 contacted benz dealer in west caldwell, nj. Explained to rep. That there was a recall on my vehicle for faulty airbags that when they are deployed had metal and could cause harm or death to passengers. the rep indicated that they do not know when my airbags would be replaced. she put in a call to service dept. so me and my family, including grandchildren have to ride around in a very unsafe vehicle and the benz dealer seem as though they just don't care. they should be made to give you another safe SUV to use until the one you have IS fixed. this IS a horrific situation. I want to stop payment, due to the situation.
- Power train
While driving on the highway approximately 65 mph in 7TH gear in the automatic 'drive' transmission mode the car switched itself into neutral for a couple of seconds (losing all power/throttle) until switching itself directly back into 7TH gear. Then did the same thing again approximately 5 seconds later. Each episode of having no access to power in neutral lasted approximately 2 seconds.
- Air bags
Still waiting from november 2017 to now february 2018. No replacement no notice no nothing. Please help
- Air bags
Takata recall
- Unknown or other
I was driving south on us 41 in lake forest il when the sunroof suddenly exploded. The fabric sunscreen was on and prevented the glass from hitting the driver or passengers.there were no bridges in the area. Nothing hit our windshield either. Photos of the damage showed no evidence of rocks or…
I was driving south on us 41 in lake forest il when the sunroof suddenly exploded. The fabric sunscreen was on and prevented the glass from hitting the driver or passengers.there were no bridges in the area. Nothing hit our windshield either. Photos of the damage showed no evidence of rocks or other objects mixed in with the glass fragments.copies of the photos are available by request. we are concerned the sunroof was defective and IS a safety hazard...updated 10/27/15 *bf updated 11/22/2017*cn
Defect investigations
NHTSA’s Office of Defects Investigation opened these reviews into vehicles including this one.
- Desiccated Air Bag Inflator Rupture
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant…
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
- Front Roof Panel Detachment
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class…
On January 8, 2021, after ongoing review with Mercedes Benz, the National Highway Traffic Safety Administration (NHTSA) Office of Defects Investigation (ODI) opened PE21-001 to assess allegations of front roof panel detachments while driving at highway speeds in certain 2015 Mercedes-Benz (Mercedes) C-Class vehicles.The subject front roof panel is a stationary panel composed of polycarbonate and is attached to the vehicle via adhesive at the time of manufacture. The panel is found on subject vehicles equipped with panoramic sunroofs. Over time, the subject panels may exhibit cosmetic degradation leading to replacement of the panel, a procedure which entails: removal of the old panel and adhesive, site preparation, and installation of a replacement panel with new adhesive.The consumer complaints that prompted the opening of PE21-001 all described detachments of front roof panels that had been replaced after the vehicle was put into service.Mercedes' internal investigation identified a broader scope of affected vehicles (2014-2020 CLA, GLA, C, S, GLC, and GLE class) and found the following potential service procedure- related causes of front roof panel detachments:- Improper surface pretreatments such as the use of the wrong primer or cleaner or scoring of the surface; or - Use of the incorrect adhesive.These conditions lead to a front roof panel bond that, even if sound at the time of repair, cannot maintain its strength over time and environmental exposure.Mercedes updated its service and parts ordering systems to reinforce the proper use of specified kits and procedures via webinars, shop foreman meetings, and explicit reference to the risks incurred by diverging from the repair procedures. Mercedes is also furnishing parts ordering assistance, and will hold dealerships accountable for improper repairs.ODI's analysis of the ten complaints it has received from the public (VOQ's) and MBUSA's complaint data submitted in response to the information request letter for PE21-001 identified a total of 57 non-duplicative reports alleging incidents in which the front roof panel detached from the vehicle while in motion. Included within the 57 reports are incidents where consumers state the panel detached ...and flew off into traffic.On March 19, 2021, Mercedes notified NHTSA that it would recall subject vehicles with front roof panels known to have been replaced after the original sale of the vehicle. In total, the recall (designated as Recall 21V197) covers 15,099 vehicles that were ever registered in the United States. Based on Recall 21V197 and the remedy implemented by Mercedes, further investigation does not appear to be warranted at this time.Accordingly, this investigation is closed.The ODI complaints cited above can be viewed at www.nhtsa.gov under the following ODI identification numbers: 11376425, 11352686, 11351629, 11349158, 11341541, 11337594, 11324100, 11311591, 11222127, 11404183
Service bulletins
Technical service bulletins and other communications the manufacturer sent dealers about this vehicle. Ask a dealer for the full document by its number.
- 11010818Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy It is important that LI54.15-P-057373 is processed before replacing any component parts (transmission 722.9). After processing and complying with the above documents, perform a reset on the transmission control unit Y3/8n4 (VGS) (ignition reset), check that the transmission connector is seated correctly and inspect the PINs for concerns. If communication with the VGS cannot be established afterwards, the component part 'electrohydraulic controller unit (EHS)' must be replaced, as it is not possible to transfer the valve characteristics under the above-mentioned conditions. Installation of a VGS repair kit is not permitted in this case.
- 11010755Complaint After a control unit replacement of "N112/9 - control unit for telematics services (HERMES)" or the "N112/2 - control unit for telematics services (RAMSES)", the Digital Extras (previously Mercedes me) cannot be activated. The DTC B15CE00 is active or active+saved. In vehicles with "N112/9 - control unit for telematics services (HERMES)": The message "SOS - service not activated" permanently lights up in the instrument cluster AND the actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/9 - control unit for telematics services (HERMES)", the registration error "CEP Invalid VIN/UniqueID combination" is displayed. In vehicles with "N112/2 - control unit for telematics services (RAMSES)": The actual value "Error when replacing certificate (CEP.36)" is displayed in the actual values for the activation status under "Registration status" (see picture 1). In the control unit log of the "N112/2 - control unit for telematics services (RAMSES)", the registration error "CEP_ VIN_UNIQUEID_INVALID" is displayed. The emergency call is not impaired. Cause In the event of a control unit replacement, sporadic problems in the back end could result in data from the new control unit not being updated in the back end system. Remedy Please create a TIPS case. In some cases, the problem rectifies itself on its own after a little while.
- 11010494Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress). Note: -If no reduction in the degree of fogging is visible, the rear lamp is defective and must be replaced. -It is not physically possible to defog the headlamps completely some residual fogging may remain. Fogging does not impair the functionality or the service life of the rear lamps. -Simultaneous fogging of multiple component parts indicates extreme climatic conditions and also does not impair the functionality or the service life of the rear lamps. Remedy 2: You can recognize a defective rear lamp as follows: 1. Check the rear lamps to ensure that no external damage is present, and that the differential aeration cells and the diaphragm are present and correctly seated. -> If there are signs of external damage on the rear lamp, the component parts must be replaced as per WIS instructions. 2. Check the electrical connectors of the plugs and pins. -> If moisture/corrosion/etc. is present, the component part must be replaced as per WIS instructions. 3. Check for leak tightness -> Close all openings with Terostat IX or similar and establish and stabilize via an overpressure (4050 mbar) via the plug. -> In the event of a sudden pressure drop, the component part must be replaced as per WIS instructions. Note: External damage to the rear lamps does not constitute a warranty or goodwill case.
- 11009122Complaint Washer fluid system leaks Cause Various possible causes: 1. Washer fluid reservoir itself. 2. Seal on washer fluid pump/washer fluid reservoir. 3. Washer fluid pump. 3.1. Distributor housing leaks. 3.2. Pump fitting leaks. 3.3. Washer fluid hose cannot be snapped into place on pump fitting. 3.4. Washer fluid hose will not stay on pump fitting, although connector OK. 4. Washer fluid line. 4.1 Connector will not stay on pump fitting because it is broken. 4.2 Sealing ring in connector missing. 4.3 Sealing ring in connector fitted, but deformed and therefore leaks. 4.4 Damage to washer line by animal. 5. Seal on heating washer fluid reservoir/washer fluid reservoir. Remedy Replace defective component parts only. Do not replace any adjacent component parts that are intact. Note: Repair kits for washer line hoses do exist to allow patches for line damage.
- 11008323Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove headlamps. 2. Remove all grommets from outlet openings. 3. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation diaphragm to work properly! 4. Remove existing service cover. 5. Place desiccant packs into the new service covers and bolt down (Picture_01). 6. Glue the new diaphragm onto the intended surface at the service cover (Picture_02). Note: The bonding surface must be clean and dry. 7. Attach service cover with desiccant pack at headlamp. 8. Install headlamp. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_03). 2. The new transparent diaphragm must be correctly bonded (Picture_04). 3. Check headlamp housing for any external damage.
- 11008091Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21) in the headliner. C. Dirt inside the microphone housing Remedy 1. Press finger on rear of microphone (on adhesive tape) 2. Remove microphone cap from the front 3. Eliminate protruding material residues of the microphone cutout at the headliner, e.g. with a soldering iron. The microphone must be seated in the headliner as shown in picture "2". 4. Push microphone from behind until it is firmly pressed into the headliner 5. Maintain pressure and press/clip cap into microphone from the front. Note: The cover cap must be clearly heard and felt to engage. 6. This procedure must be carried out on both microphones (B25/20 and B25/21) Note: It is recommended to replace the cover caps. The non-woven cloth in the cover cap protects the microphone from soiling and must not be removed. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicles warranty in any way.
- 11008032Complaint Noises/ squealing from the service brake in various driving situations and ambient conditions Cause Frictional vibrations Remedy AMG brake systems are designed for high loads. This can result in noises under certain operating conditions. These are dependent on speed, brake pressure or ambient conditions such as temperature and air humidity. (Extract from the owner's manual) If customer complaints are received, please proceed as follows: Check whether, apart from this document, an additional document exists for the model series in question, and if so, work through it Check whether the complaint can be reproduced and at which axle the noises occur (ideally together with the customer while driving) Check the friction pairings of the affected axle for wear, mechanical damage or localized overheating damage. a) If this is the case, replace the damaged component parts and assess the brake again with regard to noise. b) If there no obvious visible or technical problems with the brake system, we recommend bedding in the brakes by following the procedure below: Before trip, the mileage incurred must be clarified with the customer (approx. 50 km) Select a suitable route Brake the vehicle 15 times with a brake pressure of approx. 30 bar (have the passenger read it out using XENTRY) from 100 km/h to 50 km/h (no emergency stops and no braking in the ESP control range). Maintain a cooling distance of approx. 1.5 km between brake applications Finally drive approx. 5 km to allow the system to cool Reassess the problem If this action fails to deliver the desired success, create a TIPS case with the following information: Observe SI00.00-P-0086A Have parts already been replaced? If yes, when and which parts (date, mileage)? How is the customer's driving profile, and when/where is it reproducible? Create a video/ sound file Attach usable pictures of the brake components on the affected axle (important: including the back of the lining)
- 11007974Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front Fog Lamps Leaking or Fogged". 1. Prepare headlamp/check for external damage: For headlamps with a closed system 1. Check the headlamps for any external damage and check also for correct seating of the Gore-diaphragm/correct latching of the cover caps. 2. If the headlamp exhibits any external damage, replace the headlamp. For headlamps with an open system 1. Check the headlamps for any external damage and seal off the vent then make sure the cover caps are latched correctly into place. 2. If the headlamp exhibits any external damage, replace the headlamp. Note: A headlamp with external damage is not a warranty or goodwill case. 2. Leak test of headlamp with overpressure: Connect test adapter to pressure tester. (Figure 1) Check test adapter for leak tightness. To do so, connect plug and coupling (picture 2) and apply a maximum overpressure of 30 mbar. The pressure must remain constant. If the pressure does not remain constant, use a new adapter. Seal all the outlet openings using sealing compound and the given diaphragm with the plunger (picture 3). (Picture 4) Make allowance for the different headlamp variants here (there are different outlet openings). Check if the headlamp needs to be removed to gain access to the diagnostic socket on the headlamp housing. Plug the adapter onto the diagnostic socket on the headlamp housing. (Picture 5). Apply a maximum of 30 mbar overpressure to the headlamp housing. Note: If the maximum overpressure of 50 mbar is exceeded the headlamp seal will be damaged. If a pressure drop of less than 10 mbar is measured within 30 seconds, the headlamp is not leaky and the problem is down to natural physical fogging. If a pressure drop of more than 10 mbar is measured within 30 seconds, the headlamp is leaky. Note: The leaky position can be localized with the aid of soap suds. Replace any leaky headlamps. Note: Desiccant packs can be installed for headlamps that are not leaky. See: LI82.10-P-064766 Fogged headlamp, desiccant pack installed - open ventilation system LI82.10-P-078304 Fogged headlamp, desiccant pack installed - closed ventilation system
- 11007790Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation. Moisture is either absorbed by the plastic material and, when the light source is switched on, it is released from the plastic by desorption, or the moisture penetrates through the plastic materials of the headlamp from outside (permeation). This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check headlamps for natural fogging or condensation as per LI82.10-P-078301. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. Note: Order service covers and desiccant packs based on the validity description. 1. Remove existing service cover with diaphragm (Picture_01 (1)). 2. Insert desiccant packs (Picture_01 (2)) into new service covers with diaphragm and seal with protective grille and bolt down (Picture_01 (3)). Note: One desiccant pack is required for each small service cover, and two desiccant packs are required for each large service cover. 3. Stick the supplied diaphragm onto the new service cover and attach at the headlamp. Note: The bonding surface must be clean and dry. 4. If the headlamp housing has an additional 2nd diaphragm, this must be covered over with masking tape. Note: The bonding surface must be clean and dry. To ensure that the desiccant pack (absorption) acts effectively, the headlamp has to be air-sealed. Observe or check the following points for this: 1. Seals at the central connector must all be present and correctly fitted (Picture_02). 2. The new transparent diaphragm must be correctly bonded (Picture_03). 3. Check headlamp housing for any external damage.
- 11007753Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear lamps: 1. Drive vehicle into workshop (temperature higher than +18 C/+64.4 F) and connect the exhaust extraction. Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the hood or trunk. 4. Switch on the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Clearing fogged/condensed halogen/xenon headlamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4F). Note: Do not perform an engine wash before the defogging test. 2. Switch off the engine. 3. Open the hood. 4. Switch off the lights. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation, a significant reduction in the formation of condensation must be clearly recognizable (thawing progress). Note: If there is no visible reduction in the formation of condensation, check the headlamp for a defect. (See Remedy 2) It is not physically possible to defog the headlamps completely. Fogging does not impair the operation or the service life of the headlamp. Remedy 2 A Damaged headlamp can be identified as follows: 1. Check the headlamp for external damage and that the cover caps and the diaphragm are correctly seated. 2. Check the electrical connectors of the plugs and pins. 3. Check for leak tightness in accordance with LI82.10-P-078307. The test can only be conducted on headlamps. 4. If the headlamp or the rear lamp has any external damage, replace the component part in accordance with the WIS instructions. Note: External damage to the headlamp/rear lamp or faulty seating of the cover caps does not present a warranty or goodwill case. With headlamps, it is possible to install desiccant packs if the problem occurs repeatedly. Open ventilation system: LI82.10-P-064766. Closed ventilation system LI82.10-P-078304
- 11005294Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 C/+64.4 F) Note: Do not wash the vehicle or subject it to high-pressure cleaning before the defogging test. 2. Switch off the engine and connect battery support via a charger. 3. Open the trunk. 4. Switch on the exterior lighting. 5. Leave the vehicle in this state for 60 minutes. 6. Check for formation of condensation -> a significant reduction in the formation of condensation must be clearly recognizable (defogging progress).
- 10248162Crease formation on genuine leather seat covers in vehicles with low mileage Objects left on the seats for extended periods of time (pressure marks). Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). Light initial creases due to vehicle handling. Light creases in the outer covers originating from the production process (missing finish). Heat treatment of the seat covers using heat gun and plastic wedge. Be very careful to not overheat the seat material!
- 10241790The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a software update as well as coding. The fault will be rectified by the newly included coding. As a result of the software update to the current software of the control unit N112/9 - Control unit for telematics services (HERMES), this fault will no longer occur in future.
- 10205841Spare wheel.
- 10205200Parktronic inoperable.
- 10179966Incorrect time and/or instrument cluster message "SOS, service not activated" and/or Mercedes Me connect services nonfunctional
- 10179904Implausible "service due" instrument cluster message, head unit pop-up, or Mmc message
- 10177571Lamp unit fogged or droplets forming. Due to the vent openings, the lamp unit is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate it. This can result in deposits on the diffuser and lens. Check housing cover of lamp unit for natural fogging or dew as per GI82.10-P-009047. . 1. If a reduction in the degree of fogging is visible, the desiccant packs can be used once the condensation has completely evaporated. 1.1. Order the required service covers by referring to the variant overview. 1.2. Remove lamp unit 1.3. Remove all grommets from vent openings. 1.4. Seal vent openings with sealing profile. Important: All openings must be sealed carefully for the pressure compensation membrane to work properly! 1.5. Remove existing service cover 1.6. Place desiccant packs in new service covers and bolt down 1.7. Stick new diaphragm onto specified surface on service cover [picture of service cover] Note: The bonding surface must be clean and dry. 06
- 10176670To enhance the satisfaction of our customers, avoid further costs of litigation and return focus to its core businesses, Mercedes-Benz USA, LLC (MBUSA) has entered into a settlement regarding claims relating to alleged mold and mildew type odors originating from the HVAC system in certain Mercedes-Benz vehicles. As part of the settlement, MBUSA has agreed to offer sliding-scale warranty coverage for certain vehicles diagnosed as having mold or mildew type odors originating from the HVAC system?although that coverage will not take effect until the settlement is judicially approved and other events occur; likely not until December 7, 2020 at the earliest (see below). If the settlement becomes effective, coverage will include cleaning of the evaporator and replacement of the HVAC filters
- 10171637Retrofitted front door exit lamps with logo projection flicker
- 10167551Vehicle wanders to the left or right.
- 10167550Single, throttle lift-off, clunking noise from the side shaft when starting off (audible at the wheel). The clunk is heard once when changing from forward to reverse (and vice versa).
- 10167518Creaking noises in area of center console
- 10167517The center stowage compartment does on close or open smoothly.
- 10167512ESP, BAS, PRE-SAFE, HOLD function, Hill-Start Assist and ESP trailer stabilization are unavailable due to a malfunction. Also the adaptive brake lights, Adaptive Brake Assist and/or ATTENTION ASSIST may have failed or be deactivated. The brake system continues to operate with normal effectiveness. The support functions listed may have failed, but are available again after an ignition off/on cycle. One or more of the faults relating to the accelerator pedal (B37) listed under 'Control unit / Fault code' are stored in the engine control unit. Consequential faults may be stored in the ESP; see also under 'Control unit / Fault code'.
- 10167511Engine diagnosis warning lamp is active. One or more of the faults listed under 'Control unit / Fault code' relating to the throttle valve actuator (M16/6) and/or oxygen sensor (G3/1 and/or G3/2) are stored in the engine control unit.
- 10167510The vehicle cannot be started The vehicle may start by itself shortly after the startup attempt with a delay, as the relay can be late closing. and/or The gear selection is displayed, but no gear is engaged. Gear selection is not possible. and/or Rear window wiper inoperative. and/or Various fault codes concerning disrupted communication paths are stored and/or the corresponding control units are not displayed in the quick test. Affected control units include the transmission control unit, electronic ignition lock, driver SAM, engine control unit, Lane Keeping Assist, Distronic.
- 10167495Coolant warning message in the instrument cluster although the coolant level is OK
- 10167492Engine diagnosis warning lamp active - check engine light (CEL) on. The fault code P052E71 is logged in the fault memory of the engine control unit.
- 10167018Blind Spot Assist may warn for no obvious reason (visual and then acoustic warning message).
- 10167000Surface damage on steering wheel trim
- 10166987Transmission intermittently fails to shift, vehicle jolts in higher gears. The dual clutch transmission (DKG) control unit contains the stored FC 92177 or 92100 - The shift valve of the internal shaft has a malfunction. The commanded position was not reached. In the extended fault freeze frame data it can be seen that this fault was set in 7th gear - see Figure 1 in attachment.
- 10166981Implausible coolant warning message in instrument cluster
- 10166976Message in instrument cluster "DISTRONIC PLUSCurrently Unavailable - See Owner's Manual"
- 10165847Diverse fault messages in instrument cluster. Distronic, ESP, tire pressure monitoring, engine indicator lamp Diverse CAN communication errors stored in quick test Possible malfunctions in Parktronic or Active Parking Assist. Possible malfunctions of PTC heater booster.
- 10165845Vehicle rocks or lurches once after sitting in park with engine running for roughly 10 minutes
- 10164810Throttle lift-off clunking noises at drive shafts of front axle
- 10160738Update engine electronics (ME-SFI) control unit software
- 10160735Update restraint system control unit software
- 10158340Lever for seat height adjustment worn
Every Mercedes-Benz AMG CLA45 model year
Bars are owner complaints, dots mark years with recalls. Select a year to open its report.